irix 6.5.10 图形系统不能启动？

tth0561

octane 2,配置双显示模块ESI双显示器,irix 6.5.10启动图形界面时，显示器闪烁两下，黑屏查看/var/adm/SYSLOG

Jul 17 19:53:06 4Actane unix: |$(0xa9c)WARNING: mgras: CTXSW timeout
Jul 17 19:53:06 4Actane unix: |$(0xa9e)WARNING: Graphics error
Jul 17 19:53:06 6Actane unix: gfx board #1
Jul 17 19:53:06 6Actane unix: irnode=0xa8000000212cb1b8,  active_rnode=0xa8000000212cb1b8
Jul 17 19:53:06 6Actane unix: busy_dma:       0x900000001a020200/0x200
Jul 17 19:53:06 6Actane unix: status: 0x900000001a020000/0xe4352
Jul 17 19:53:06 6Actane unix: fifo_status:    0x900000001a020008/0x47000000
Jul 17 19:53:06 6Actane unix: bfifo_status:   0x900000001a020100/0x0
Jul 17 19:53:06 6Actane unix: rebus_sync:     0x900000001a05821c/0x2
Jul 17 19:53:06 6Actane unix: window: 0x900000001a008000/0x100
Jul 17 19:53:06 6A:octane unix: hqpc:   0x900000001a056000/0x285
Jul 17 19:53:06 6A:octane unix: flag_set:       0x900000001a020010/0x40000100
Jul 17 19:53:06 6A:octane unix: hq_config:      0x900000001a011000/0x41085
Jul 17 19:53:06 6A:octane unix: gio_config:     0x900000001a011008/0x900f
Jul 17 19:53:06 6A:octane unix: re_status:      0x900000001a02c578/0x120
Jul 17 19:54:18 3B:octane xdm[1141]: Hung in XOpenDisplay(:0), aborting
Jul 17 19:54:18 3B:octane xdm[1141]: server open failed for :0, giving up
Jul 17 19:54:18 3B:octane xdm[1135]: Display :0 cannot be opened
请求帮助

sgi

你的显卡以前是好的吗?你对系统作了什么改动吗?
你用hinv看看,首先排除硬件的问题,再来看软件的问题!

tth0561

显卡以前是好的，用hinv查看正常，当我去掉第二块显卡，图形界面启动正常，后来重新插上第二块显卡，系统又好了。
我是在运行一个图形应用程序时，死机。冷起后出的故障。
未做任何改动

tth0561

正高兴呢，今天又停了。

sgi

硬件没有问题的话,可能是你运行的程序影响的,打打补丁吧!

race

OCTANE就是那毛病,把主板拔下来,再插上去,可能就好了.再不行就把显示卡也拔下来晒晒,再装上去

tth0561

君子所见略同，同意你的观点

phenix_chang

原来octane真的晒晒就好了

szh

常有的事情~！

En_route

Sounds very interesting especially when I am about to acquire a second-hand octane...

If you could kind enough to provide the following details:

1. What level of sunlight (laymen description would do, e.g. very bright sunlight, normal sunny day, overcast day, morning sun, evening sun etc.,):


2. What is the ambient temperature?

3. For how long?

4. Do you think that the cure relates to

(a)  ultraviolet on some electronic components

(b)  ultraviolet kills certain bacteria

(c)  warming of the board to correct certain tolerances (e.g. dimensions of contacts)

(d) any other reason you can acribe to this bizarre phenomenon

Thanks