HA 再次提问，谢谢告诉讲解

yongi

clver -c -V normal -O -t -r -e 100 -R /var/hacmp/log/autoclstrcfgmonitor.out -V normal -O     Mon Aug 18 00:09:30 2008

Verification to be performed on the following:
        Cluster Topology
        Cluster Resources

Retrieving data from available cluster nodes.  This could take a few minutes.........................................................................


Verifying Cluster Topology...





Verifying Cluster Resources...

ERROR: Logical volume datadbs_chk1 not found for VG appvg on node p570b.
ERROR: Logical volume datadbs_chk1_cs not found for VG datavg on node p570a.

WARNING: Application monitors are required for detecting application failures
in order for HACMP to recover from them.  Application monitors are started
by HACMP when the resource group in which they participate is activated.
The following application(s), shown with their associated resource group,
do not have an application monitor configured:

   Application Server                Resource Group
   --------------------------------  ---------------------------------
   app                               app_res                        
   data                              data_res                        
A corrective action is available for the condition reported below:

WARNING: The LVM time stamp for shared volume group: appvg is inconsistent
with the time stamp in the VGDA for the following nodes:
p570a

To correct the above condition, run verification & synchronization with
"Automatically correct errors found during verification?" set to either 'Yes'
or 'Interactive'.  The cluster must be down for the corrective action to run.

Corrective actions can be enabled for Verification and Synchronization in the
HACMP extended Verification and Synchronization SMIT fastpath "cl_sync".
Alternatively use the Initialization and Standard Configuration -> Verification
and Synchronization path where corrective actions are always executed in
interactive mode.
A corrective action is available for the condition reported below:

WARNING: The LVM time stamp for shared volume group: datavg is inconsistent
with the time stamp in the VGDA for the following nodes:
p570a

To correct the above condition, run verification & synchronization with
"Automatically correct errors found during verification?" set to either 'Yes'
or 'Interactive'.  The cluster must be down for the corrective action to run.

Corrective actions can be enabled for Verification and Synchronization in the
HACMP extended Verification and Synchronization SMIT fastpath "cl_sync".
Alternatively use the Initialization and Standard Configuration -> Verification
and Synchronization path where corrective actions are always executed in
interactive mode.
ERROR: The following tty devices are enabled in /etc/inittab
on the following cluster node(s):

Node Name                        Device            Identifier        Action
-------------------------------- ----------        ----------        -------
p570a                            /dev/tty0        tty0                respawn

RSCT will be unable to start until these entries are removed or disabled
within /etc/inittab.
Please remove these entries, or change the action to 'off' then run
'init q' to stop the getty or terminal processes.

Verification exiting with error count: 3

myciciy

还是那个问题
串口心跳有问题吧 重新配置测试一下吧

ERROR: The following tty devices are enabled in /etc/inittab
on the following cluster node(s):

Node Name                        Device            Identifier        Action
-------------------------------- ----------        ----------        -------
p570a                            /dev/tty0        tty0                respawn

RSCT will be unable to start until these entries are removed or disabled
within /etc/inittab.

myciciy

ERROR: Logical volume datadbs_chk1 not found for VG appvg on node p570b.
ERROR: Logical volume datadbs_chk1_cs not found for VG datavg on node p570a.

lv没同步

具体信息不够 无法判断啊

lsvg -l appvg
lsvg -l datavg

双机热备 ？互备？
建lv最好用cspoc做

yongi

谢谢