关于安装V5R4M5的怪问题 求救

zhangzx911

9406-520  0902的机器，4326的硬盘，原先是V5R3的系统，现全新安装系统，DM起安装完V5R4M5的微码，重启AM安装完B2984-01 02这两张盘，进入系统，准备安装LICPGM,发现基本的
LICPGM里QGPL 和QUSRSYS这两项状态变成了*BACKLEVEL，怎么回事啊！！！ 系统硬盘都已经初始化和重新做过RAID。另外装V5R4M0的微码也是这样！！

除了微码的光盘，其他光盘都是新ORDER过来的，是做V5R3升级得到的光盘。

不知道是不是升级拿到的系统光盘和全新安装系统的光盘有区别啊。

急。。。！！！

另外和大家分享：像此类机器用DM装V5R4M5的微码是不能用OP CONSOLE的，只能调用LAN CONSOLE或者 HMC才能找到CONSOLE。

还有现在机器有个错误B1814008  现在只能用 01 A M V=F  P 启动 ，如果把P改成T就报此错，郁闷中。。。。

居士

这个状态事正常的
安装完LIC,和base的OS后,下面继续装License program,  QGPL, QUSRSYS这2个必须选上.

zhangzx911

这两项是BACKLEVEL的状态的话不能安装OS和LICPGM啊！提示不能安装，找不到QPRINT，以前装系统第一次用AM进后，这两项都不是这样的状态的

居士

提示找不到QPRINT也是正常的

机器重启一下, END掉全部子系统, 再装(第一次几乎可能还会报找不到QPRINT),没事,再装一次就好了.

qingzhou

1. 
   
2. 另外和大家分享：像此类机器用DM装V5R4M5的微码是不能用OP CONSOLE的，只能调用LAN CONSOLE或者 HMC才能找到CONSOLE。
   
3. 
   

复制代码

V5R4M0可以支持OP CONSOLE方式安装，怎么到V5R4M5就不支持了呢？！

Oo懒觉熊...

   用DM 安装微码，三种方式的CONSOLE都好用的啊。

居士

LZ的机器有点怪

根据经验，比较妖的机器，会不停的出各种妖怪的问题，LZ节哀

arrike

请注意，v5r4m5的系统支持less－iop，因此，控制卡的位置就必须改变，比如说，需要将9733这张卡安放在C04的位置上，

v5r4m5的内码盘引导，用5544作控制方式是比较麻烦的事情

qingzhou

今天我也遇到在9406-i520上装好V6R1M1后,安装PTFs,结果机器IPL后就卡在B1814008了,后来查询手册才知道是因为机器的Firmware要打到SF230_150_120以上.否则就会出现类似故障.

http://ps-2.kev009.com:8081/rs6000-firmware/DescHist_CD.htm


SF230_150_120

Impact:  Function   Severity:  Special Attention
New function:

On i5 systems, added support for booting from a boot device attached to an IOP-less adapter.
Added support for the installation of two copies of the AIX operating system on one hard file.  This includes support in the SMS menus for booting from either one.
Added support for feature code 1812, the GX Dual-port 4x InfiniBand Host Channel Adapter, on model 52A systems.
Added support for feature code 1811, the GX Dual-port 4x InfiniBand Host Channel Adapter, on model 575 systems.  
Added support for moving the CUoD resources from one system to another system.
Added support for the capability to set up a backup shared ethernet so that the shared ethernet function can fail-over to a standby shared ethernet if the primary fails. This function is part of the virtual IO server.
Added support for redundant service processors with dynamic failover in models 570, 590, and 595.
Added support for modifying the number of On/Off CoD activations during the active period.
Added support for unattended HMC installation over a network, and to back up full HMC disk images onto a network server.
Added support for new models:  9131-52A, 9111-28 , 9133-55A, 9110-51A, 9115-505.
Various enhancements to the ASCII version of the Advanced System Management Interface (ASMI) menus were made.
Problems resolved:
Fixed a problem that was causing the user data in a service processor error log entry generated by the bulk power controller to be truncated to 2048 bytes.
Fixes a problem that caused unnecessary Service Agent calls because SRC B1816009 was being generated when the white power button was pressed before the power-on sequence was complete.
On model 590 and 595 systems, fixed a problem that was causing DDR II memory cards in slots C10 and C12 to fail the memory test during a slow-mode boot.
Fixed a problem that was causing a platform dump to be incomplete under certain circumstances.
Fixed a problem that was causing a hypervisor dump to be corrupted.
Fixed a problem that caused the location codes to be incorrect after the planar is replaced in a pSeries 7311-D20 drawer.
The timestamp from the bulk power controller was added into the serviceable event log entry.
Fixed a problem that prevented the "nvunalias" open firmware command from working.
Fixed a problem that kept the physical I/O description field on the HMC GUI from being updated after a "remove FRU and add FRU" operation.  
Fixed a problem that caused a service processor dump or a platform dump and SRC B1817201 or B7004400.  
Changed the firmware so that a modem attached to a system port will reconfigure to enable call-in following a power failure.
Fixed VPD-related command hangs (such as lsmcode, lsvpd, snap)
Fixed several problems associated with firmware installations:
SRC B1814008 or B181F131 was generated on reboot
A service processor dump occurred during a firmware installation
"lsmcode -c" command displayed all zeros for the firmware level on the T side after an installation

edna

回复 9# qingzhou


    请问如何升级固件？