- 论坛徽章:
- 89
|
感觉中文的编译速度有点慢,
我只是重新安装了一下latex-cjk,然后看了看,安装最后出现的提示,然后就搞定了。
1. To embed Type 3 fonts in PostScript/PDF files or to use DVIPDFMx
for TrueType fonts embedded and CID-keyed PDF files, use the
following basic font names:
\begin{CJK}{Bg5}{song}
\begin{CJK}{Bg5}{kai}
\begin{CJK}{GB}{song}
\begin{CJK}{GB}{kai}
2. By using "ccmap" with CJK, PDF generated by PDFTeX ("ccmap" does NOT
work with LaTeX, DVIPS, DVIPDFm, etc.) may be searched for Chinese
text, and may be copied Chinese text from, when viewed in Adobe Reader.
BIG5, BIG5+, GB2312, GBK, JIS and UTF-8 are supported (Korean is
supported ONLY in UTF-8 so far). This implementation is based on
PDFTeX's CID support.
Usage:
\usepackage{ccmap}
\usepackage{CJK}
...
The package "ccmap" is a part of "CCT", an alternative to CJK,
another excellent Chinese support package for LaTeX, developped
and maintained by Lin-bo Zhang <zlb@lsec.cc.ac.cn>, Institute of
Computational Mathematics and Scientific/Engineering Computing,
China Academy of Science. See:
http://lsec.cc.ac.cn/cgi-bin/viewcvs.cgi/cct/
ftp://ftp.cc.ac.cn/pub/cct/
The package "ccmap" is rewritten by Wen-chang Sun
<sunwch@nankai.edu.cn>, School of Mathematical Science, Nankai
University, based on "cmap" package by Vladimir Volovich
<vvv@vsu.ru>.
3. Except with DVIPDFM, you may use pseudo-italic Chinese fonts by:
\textit{...} or \textsl{...}
4. To use PDFTeX DIRECTLY with TrueType fonts for TrueType fonts
embedded PDF file, please run (see ATTENTION below):
cat `kpsewhich CJK-pdftex.map` >> `kpsewhich pdftex.map`
This command injects PDFTeX-specific configuration for TrueType
into PDFTeX's own configuration file.
See also the above introduction to "ccmap" for PDFTeX's CID support.
ATTENTION: Due to PDFTeX's bug (version < 1.30.0) against Arphic
free BIG5 TrueType fonts' bugs, PDFTeX exits abnormally when using
"AR PL Mingti2L Big5" ("ShanHeiSun-Light" and "AR PL KaitiM Big5"
("ZenKai-Medium". See
http://sarovar.org/tracker/index ... id=106&atid=493
NOTE: PDFTeX-specific configuration will be eliminated by running
"updmap" or "updmay-sys". After that, you MUST RE-RUN the above
command to do RE-INJECTING.
5. Use these font names in UTF-8 TeX files (if UTF-8 support is enabled):
\begin{CJK}{UTF8}{b5song} % Arphic Mingti, BIG5 glyphs covered
\begin{CJK}{UTF8}{b5kai} % Arphic Kaiti, BIG5 glyphs covered
\begin{CJK}{UTF8}{gbsong} % Arphic Songti, GB2312 glyphs covered
\begin{CJK}{UTF8}{gbkai} % Arphic Kaiti, GB2312 glyphs covered
6. If you want to use Type 1 fonts, use the following font names:
\begin{CJK}{Bg5}{t1song}
\begin{CJK}{Bg5}{t1kai}
\begin{CJK}{GB}{t1song}
\begin{CJK}{GB}{t1kai}
But to be honest, they look VERY BAD in Adobe Reader (but fine
in Xpdf and GhostScript), though they are REAL SCALABLE fonts
and may be enlarged by any ratio.
To see these tips again, run
pkg_info -D zh-CJK-\* | less
Happy CJKing!
*********************************************************************
* ATTENTION !!! ATTENTION !!! ATTENTION !!! *
* *
* Your old personal configuration files in $HOME/.texmf-var/ and *
* $HOME/.texmf-config/ may DISTURB this new port CJK. If you have *
* your specific settings in them, please: *
* 1. Backup your own configuration files in $HOME/.texmf-var/ and *
* $HOME/.texmf-config/ *
* 2. Run "updmap" *
* 3. Rewrite your specific settings into newly-generated files in *
* $HOME/.texmf-var/ and $HOME/.texmf-config/ *
*********************************************************************
===> Compressing manual pages for latex-cjk-4.8.2
===> Registering installation for latex-cjk-4.8.2 |
|