[VTL与磁带系统] netwoker 7.5sp1识别不到M2500带库(Sun StorageTek L100)的机械手？ [复制链接]

nimysun

版主

论坛徽章:: 7

发表于 2009-04-16 10:27 |显示全部楼层

10可用积分

root@backup # cfgadm -alv c3|c4

c3                            connected configured unknown
unavailable  scsi-bus    n       /devices/ssm@0,0/pci@1d,700000/scsi@2:scsi
c3::rmt/2                   connected configured unknown SEAGATE ULTRIUM06242-XXX
unavailable  tape       n       /devices/ssm@0,0/pci@1d,700000/scsi@2:scsi::rmt/2
c3::scsi/sequential/c3t1d0    connected configured unknown SEAGATE ULTRIUM06242-XXX
unavailable  tape       n       /devices/ssm@0,0/pci@1d,700000/scsi@2:scsi::scsi/sequential/c3t1d0
c4                            connected configured unknown
unavailable  scsi-bus    n       /devices/ssm@0,0/pci@1d,700000/scsi@2,1:scsi
c4::rmt/3                   connected configured unknown SEAGATE ULTRIUM06242-XXX
unavailable  tape       n       /devices/ssm@0,0/pci@1d,700000/scsi@2,1:scsi::rmt/3
c4::scsi/changer/c4t0d0       connected configured unknown ATL M2500
unavailable  med-changer  n       /devices/ssm@0,0/pci@1d,700000/scsi@2,1:scsi::scsi/changer/c4t0d0
c4::scsi/sequential/c4t2d0    connected configured unknown SEAGATE ULTRIUM06242-XXX
unavailable  tape       n       /devices/ssm@0,0/pci@1d,700000/scsi@2,1:scsi::scsi/sequential/c4t2d0

sgen.conf没有做任何改动，默认配置

root@backup # inquire
scsidev@0.0.0:FUJITSU MAN3367M SUN36G 1804|Disk, /dev/rdsk/c0t0d0s2
                                       S/N: 03X94694
scsidev@0.1.0:FUJITSU MAN3367M SUN36G 1804|Disk, /dev/rdsk/c0t1d0s2
                                       S/N: 03X94713
scsidev@3.1.0:SEAGATE ULTRIUM06242-XXX1527|Tape, /dev/rmt/2cbn
                                       S/N: HM00DEX
                                       ATNN=SEAGATE ULTRIUM06242-XXX HM00DEX
scsidev@4.2.0:SEAGATE ULTRIUM06242-XXX1608|Tape, /dev/rmt/3cbn
                                       S/N: HM009K8
                                       ATNN=SEAGATE ULTRIUM06242-XXX HM009K8

我的PMC、Jukebox、Tape Drivers的Microcode均已经升级到最新。

主机的OS的补丁为Solaris 10 u5 64-bits，  system patchset已经更新到今年4月份了
Legato Networker 7.5sp1也是最新的了。
安装了LGTOclnt， LGTOman LGTOnode LGTOserv LGTOnmc LGTOlic

现在的问题就是机械手死活认不到，比较了一下sgen.conf，之前的legato 7.1也是如此，但是就可以使用机械手。很奇怪昂。

朋友们帮分析一下，可能是哪个地方出现了问题？

自认为应该legato相关的参数需要调整，但是在资料中没有发现如何调整是好。

先谢过各位了。

[ 本帖最后由 nimysun 于 2009-4-16 10:51 编辑 ]

最佳答案

yddll

查看完整内容

inquire没结果也没关系on solaris os:Here is the solution: Change target=0 to target=1 in lus.conf and reboot machine If notinquire through these ways:#mt -f /dev/rmt/1cbn status //get the WWN Number#luxadm display /dev/rmt/1cbn //get the SN,WWN,etc#ls -al /dev/rmt/1cbn //get the WWN Number and SCSI portNote:if you had added tape drive or removed tape driver, ...

备份, 磁带, 备份, 磁带

文库|博客

yddll

荣誉版主

论坛徽章:: 1

发表于 2009-04-16 10:27 |显示全部楼层

inquire没结果也没关系

on solaris os:
Here is the solution: Change target=0 to target=1 in lus.conf and reboot machine
If not
inquire through these ways:
#mt -f /dev/rmt/1cbn status          //get the WWN Number
#luxadm display /dev/rmt/1cbn          //get the SN,WWN,etc
#ls -al /dev/rmt/1cbn                //get the WWN Number and SCSI port
Note:if you had added tape drive or removed tape driver, run lus_add_fp_devs again to save changes to Networker.