免费注册 查看新帖 |

Chinaunix

  平台 论坛 博客 文库
123下一页
最近访问板块 发新帖
查看: 10689 | 回复: 27

Sun V880 串口登录,能看到输出,但无法输入 [复制链接]

论坛徽章:
1
白羊座
日期:2014-05-04 17:53:33
发表于 2009-04-22 10:29 |显示全部楼层
Hi all,

Sun V880 串口登录,能看到输出,最大化自检没有报错,但到OK提示符后无法输入,为什么?

谢谢!

论坛徽章:
0
发表于 2009-04-22 10:33 |显示全部楼层
type "." or "Break" couple times.

论坛徽章:
1
白羊座
日期:2014-05-04 17:53:33
发表于 2009-04-22 10:41 |显示全部楼层

回复 #2 hlzhan 的帖子

谢谢这么快回复!:)

我试过敲入"." 或 "Break"很多次,但还是反应。:(

是不是和RSC有关?听说用过RSC后就会这样。如果是这样的话,如何再恢复成默认的串口?在OK下输入reset-all会不会奏效?

论坛徽章:
0
发表于 2009-04-22 11:49 |显示全部楼层
看一下你的输入和输出设备设得有没有错误。

论坛徽章:
1
白羊座
日期:2014-05-04 17:53:33
发表于 2009-04-22 12:07 |显示全部楼层

回复 #4 xiazhen9842 的帖子

都没有啊:

...

1:0>Basic Memory Test....Done
1:0>Full CPU Test....Done
1:0>Memory Block....Done
1:0>IO-Bridge Tests....Done
1:0>Full Memory Test....Done
1:0>Enable Errors....Done
1:0>INFO:
1:0>    POST Passed all devices.
1:0>POST:       Return to OBP.
POST Reset

Enabling system bus....... Done
Probing Memory............ Done
Initializing CPUs......... Done
Initializing boot memory.. Done
Initializing OpenBoot
Probing system devices
ChassisSerialNumber 003803
Probing I/O buses
Probing system devices
ChassisSerialNumber 003803
Probing I/O buses


Sun Fire 880, No Keyboard
Copyright 2005 Sun Microsystems, Inc.  All rights reserved.
OpenBoot 4.18.11, 8192 MB memory installed, Serial #51564264.
Ethernet address 0:3:ba:12:ce:e8, Host ID: 8312cee8.





Running diagnostic script obdiag/normal

Testing /pci@8,600000/network@1
Testing /pci@8,600000/SUNW,qlc@2
Testing /pci@9,700000/ebus@1/i2c@1,2e
Testing /pci@9,700000/ebus@1/i2c@1,30
Testing /pci@9,700000/ebus@1/i2c@1,50002e
Testing /pci@9,700000/ebus@1/i2c@1,500030
Testing /pci@9,700000/ebus@1/bbc@1,0
Testing /pci@9,700000/ebus@1/bbc@1,500000
Testing /pci@8,700000/scsi@1
Testing /pci@9,700000/network@1,1
Testing /pci@9,700000/usb@1,3
Testing /pci@9,700000/ebus@1/gpio@1,300600
Testing /pci@9,700000/ebus@1/pmc@1,300700
Testing /pci@9,700000/ebus@1/rtc@1,300070

{6}OK

显示到在这里想输入命令时就无法输入了。

论坛徽章:
1
白羊座
日期:2014-05-04 17:53:33
发表于 2009-04-22 12:10 |显示全部楼层
我接上显示器、键盘、鼠标后,输入以下命令还是不行:
ok diag-console ttya
ok setenv input-device ttya
ok setenv output-device ttya
ok reset-all

论坛徽章:
1
白羊座
日期:2014-05-04 17:53:33
发表于 2009-04-22 12:34 |显示全部楼层
晕哦,这下好了,串口还是用不了,接上键、鼠、显示器也什么都看不到了。

如何再复位成原来的状态啊,现在是最大化自检,按两个Power Button却关机了,那个钥匙也找不到了。

论坛徽章:
0
发表于 2009-04-22 12:43 |显示全部楼层
1. Press the power button to power up the system.

2. Once the maintenance LED starts to flash rapidly, immediately press the Power button twice (similar to double-clicking a mouse, but leave a short gap of around 1 second between presses, to have the action reliably registered.) The actual time when you do the double press of the power button is the point in POST when the maintenance LED (wrench light) rapidly flashes.

NOTE:

If you double press too late or too soon, the system will power off. Do not get confused with the earlier occurrences of the maintenance and OK to remove LEDs flashing together. This is a part of the system test to make sure the LEDs are functional.

If you're running POST even in MIN level, it will be several minutes depending upon your configuration, before the maintenance LED flashes rapidly.

论坛徽章:
0
发表于 2009-04-22 12:45 |显示全部楼层
多试两次  很有可能是你的串口线  或者终端设置问题  
如果不是  那可能是你的io板上的  ttya的rx部分有硬件故障。。。。。

论坛徽章:
1
白羊座
日期:2014-05-04 17:53:33
发表于 2009-04-22 13:03 |显示全部楼层
谢谢各位回复!

我拔掉了RSC卡,再用串口连上去,自检完成后还是在OK那里无法输入,我现在再改成键鼠显示器试试,如果不行就按ac220v的说法按两次power button去reset试试看。
您需要登录后才可以回帖 登录 | 注册

本版积分规则 发表回复

  

北京盛拓优讯信息技术有限公司. 版权所有 京ICP备16024965号-6 北京市公安局海淀分局网监中心备案编号:11010802020122 niuxiaotong@pcpop.com 17352615567
未成年举报专区
中国互联网协会会员  联系我们:huangweiwei@itpub.net
感谢所有关心和支持过ChinaUnix的朋友们 转载本站内容请注明原作者名及出处

清除 Cookies - ChinaUnix - Archiver - WAP - TOP