如何在freebsd假设无线AP?且使用WPA2认证?

qq830406

AP开启没问题,而且开启WPE没问题,但WPA搞不定,各种资料查了,官方的也看了下,似乎有问题,哪位有这方面的经验没?

macafee

http://cnsnap.cn.freebsd.org/doc ... twork-wireless.html

qq830406

别的都没问题,启动hostapd后ap就不work,搞不懂

macafee

不是所有网卡都支持HOSTAP功能的！

qq830406

原帖由 macafee 于 2009-6-9 10:15 发表
不是所有网卡都支持HOSTAP功能的！

注意: 目前还不支持使用 Windows 驱动和 NDIS 驱动包装的网卡做为 AP 使用。只有 FreeBSD 原生的无线驱动能够支持 AP 模式。

device          ath             # Atheros pci/cardbus NIC's

ath0=6783edcf<WEP,TKIP,AES,AES_CCM,FF,TURBOP,IBSS,HOSTAP,AHDEMO,TXPMGT,SHSLOT,SHPREAMBLE,MONITOR,TKIPMIC,WPA1,WPA2,BURST,WME,BGSCAN,TXFRAG>

已经相当原生了吧?

网卡是 TP-Link TL-WN650G

[ 本帖最后由 qq830406 于 2009-6-9 13:12 编辑 ]

qq830406

启动HOSTAP 客户端找不到网络
ath0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> metric 0 mtu 1500
        ether 00:0a:eb:a7:4f:5e
        inet 123.129.254.13 netmask 0xffffffff broadcast 192.168.0.2
        media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap>
        status: no carrier
        ssid freebsdap channel 1 (2412 Mhz 11g)
        authmode AUTO privacy OFF deftxkey 3 txpower 31.5 scanvalid 60 bgscan
        bgscanintvl 300 bgscanidle 250 roam:rssi11g 7 roam:rate11g 5
        protmode CTS burst dtimperiod 1

不启动HOSTAP状态
ath0: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> metric 0 mtu 1500
        ether 00:0a:eb:a7:4f:5e
        inet 123.129.254.13 netmask 0xffffffff broadcast 192.168.0.2
        media: IEEE 802.11 Wireless Ethernet autoselect mode 11g <hostap>
        status: associated
        ssid freebsdap channel 1 (2412 Mhz 11g) bssid 00:0a:eb:a7:4f:5e
        authmode AUTO privacy OFF deftxkey 3 txpower 31.5 scanvalid 60 bgscan
        bgscanintvl 300 bgscanidle 250 roam:rssi11g 7 roam:rate11g 5
        protmode CTS burst dtimperiod 1

hostap启动以后找不到无线网络,什么原因?



Jun 12 17:14:45 go kernel: ieee80211_load_module: load the wlan_xauth module by hand for now.
Jun 12 17:14:45 go hostapd: ath0: DRIVER Error enabling WPA/802.1X!
Jun 13 19:36:48 go kernel: ath0: ath_chan_set: unable to reset channel 6 (2437 Mhz, flags 0x490 hal flags 0x150), hal status 12
Jun 13 19:38:26 go kernel: ieee80211_load_module: load the wlan_xauth module by hand for now.
Jun 13 19:38:26 go hostapd: ath0: DRIVER Error enabling WPA/802.1X!
Jun 13 19:38:34 go kernel: ath0: ath_chan_set: unable to reset channel 6 (2437 Mhz, flags 0x490 hal flags 0x150), hal status 12
Jun 13 19:40:38 go kernel: ath0: ath_chan_set: unable to reset channel 6 (2437 Mhz, flags 0x490 hal flags 0x150), hal status 12
Jun 13 19:43:15 go kernel: ieee80211_load_module: load the wlan_xauth module by hand for now.
Jun 13 19:43:15 go hostapd: ath0: DRIVER Error enabling WPA/802.1X!
Jun 13 19:48:29 go kernel: ath0: ath_chan_set: unable to reset channel 6 (2437 Mhz, flags 0x490 hal flags 0x150), hal status 12
Jun 13 19:54:55 go kernel: ath0: ath_chan_set: unable to reset channel 6 (2437 Mhz, flags 0x490 hal flags 0x150), hal status 12
Jun 13 19:55:20 go kernel: ieee80211_load_module: load the wlan_xauth module by hand for now.
Jun 13 19:55:20 go hostapd: ath0: DRIVER Error enabling WPA/802.1X!
Jun 13 19:55:33 go kernel: ath0: ath_chan_set: unable to reset channel 6 (2437 Mhz, flags 0x490 hal flags 0x150), hal status 12
Jun 13 19:55:37 go kernel: ieee80211_load_module: load the wlan_xauth module by hand for now.
Jun 13 19:55:37 go hostapd: ath0: DRIVER Error enabling WPA/802.1X!
Jun 13 20:05:17 go kernel: ieee80211_load_module: load the wlan_xauth module by hand for now.
Jun 13 20:05:17 go hostapd: ath0: DRIVER Error enabling WPA/802.1X!
Jun 13 20:06:34 go kernel: ath0: ath_chan_set: unable to reset channel 6 (2437 Mhz, flags 0x490 hal flags 0x150), hal status 12
Jun 13 20:10:42 go kernel: ath0: ath_chan_set: unable to reset channel 6 (2437 Mhz, flags 0x490 hal flags 0x150), hal status 12
Jun 13 20:12:44 go kernel: ieee80211_load_module: load the wlan_xauth module by hand for now.
Jun 13 20:12:44 go hostapd: ath0: DRIVER Error enabling WPA/802.1X!

[ 本帖最后由 qq830406 于 2009-6-13 20:21 编辑 ]

qq830406

3.2.3 WPA-PSK
The host side:

# vi /etc/hostapd.conf

interface=ath0
driver=bsd
logger_syslog=-1
logger_syslog_level=0
logger_stdout=-1
logger_stdout_level=0
debug=4
dump_file=/tmp/hostapd.dump
ctrl_interface=/var/run/hostapd
ctrl_interface_group=wheel
ssid=freebsdap
wpa=1
wpa_passphrase=freebsdmall
wpa_key_mgmt=WPA-PSK
wpa_pairwise=TKIP
And run:

# /usr/sbin/hostapd /etc/hostapd.conf
# ifconfig ath0 mediaopt hostap

qq830406

kldload wlan_xauth.ko

嗯,嗯,正是如此