求救!!!cisco7204出错！不停重启。

andyo

一台7204，开机后报错，忘大哥帮忙看看什么问题。
*Jul 22 19:35:55.691: %SYS-5-RELOAD: Reload requested by console.
System Bootstrap, Version 12.0(19991120:010612) [nlaw-conn_4xe_ECC 112], DEVELOPMENT SOFTWARE
Copyright (c) 1994-1999 by cisco Systems, Inc.
C7200 platform with 131072 Kbytes of main memory


Self decompressing the image : ###################################################################### [OK]

%ERR-1-GT64120 (PCI-0): Fatal error, CPU out of range error
GT=0xB4000000, cause=0x0900E083, mask=0x0ED01F00, real_cause=0x08000000
bus_err_high=0x00000000, bus_err_low=0x0102B3C0, addr_decode_err=0x00000470

%ERR-1-FATAL: Fatal error interrupt, No reloading
err_stat=0x1, err_enable=0xFF, mgmt_event=0x0

System bridge dump:

Bridge 0, for PA Bay 0 (I/O Card, PCMCIA, Interfaces), Handle=0
DEC21150 bridge chip, config=0x0
(0x00):dev, vendor id       = 0x00231011
(0x04):status, command      = 0x02B00147
(0x0:class code, revid    = 0x06040006
(0x0C):hdr, lat timer, cls  = 0x0001FF08
(0x1:sec lat,cls & bus no = 0x18020100
(0x1C):sec status, io base  = 0x02A03101
(0x20):mem base & limit     = 0x48704000
(0x24):prefetch membase/lim = 0x0001FF01
(0x30):io base/lim upper16  = 0x00000000
(0x3C):bridge ctrl          = 0x00030000
(0x40):arb/serr, chip ctrl  = 0x02000000
(0x64):serr disable, gpio   = 0xF0000000
(0x6:sec clk ctrl,serrsta = 0x000001FF

PA bridge dump:

Bridge 4, Port Adaptor 1, Handle=1
DEC21050 bridge chip, config=0x0
(0x00):dev, vendor id       = 0x00011011
(0x04):status, command      = 0x02800147
(0x0:class code, revid    = 0x06040002
(0x0C):hdr, lat timer, cls  = 0x0001F808
(0x1:sec lat,cls & bus no = 0x18050504
(0x1C):sec status, io base  = 0x22805040
         Received Master Abort  on secondary bus
(0x20):mem base & limit     = 0x48F04880
(0x24):prefetch membase/lim = 0x0000FF00
(0x3C):bridge ctrl          = 0x00030000
(0x40):arb/serr, chip ctrl  = 0x00080000
(0x44):pri/sec trgt wait t. = 0x00009020
(0x4:sec write attmp ctr  = 0x00FFFFFF
(0x4C):pri write attmp ctr  = 0x00FFFFFF

Bridge 5, Port Adaptor 2, Handle=2
DEC21050 bridge chip, config=0x0
(0x00):dev, vendor id       = 0x00011011
(0x04):status, command      = 0x02800147
(0x0:class code, revid    = 0x06040002
(0x0C):hdr, lat timer, cls  = 0x0001F808
(0x1:sec lat,cls & bus no = 0x180B0B0A
(0x1C):sec status, io base  = 0x2280B0A0
         Received Master Abort  on secondary bus
(0x20):mem base & limit     = 0x4D704D00
(0x24):prefetch membase/lim = 0x0000FF00
(0x3C):bridge ctrl          = 0x00030000
(0x40):arb/serr, chip ctrl  = 0x00080000
(0x44):pri/sec trgt wait t. = 0x00009020
(0x4:sec write attmp ctr  = 0x00FFFFFF
(0x4C):pri write attmp ctr  = 0x00FFFFFF


=== Flushing messages (19:37:11 UTC Wed Jul 22 2009) ===

*** System received an Error Interrupt ***
signal= 0x16, code= 0x0, context= 0x61074d18
PC = 0x605fc328, Cause = 0x2420, Status Reg = 0x34008002

System Bootstrap, Version 12.0(19991120:010612) [nlaw-conn_4xe_ECC 112], DEVELOPMENT SOFTWARE
Copyright (c) 1994-1999 by cisco Systems, Inc.
C7200 platform with 131072 Kbytes of main memory


Read cis from dev 0 error (-6)PCMCIA slot0 device is not initialized
open: read error...requested 0x4 bytes, got 0x0
trouble reading device magic number
boot: cannot open "slot0:"
boot: cannot determine first file name on device "slot0:"

System Bootstrap, Version 12.0(19991120:010612) [nlaw-conn_4xe_ECC 112], DEVELOPMENT SOFTWARE
Copyright (c) 1994-1999 by cisco Systems, Inc.
C7200 platform with 131072 Kbytes of main memory













Self decompressing the image : ###################################################################### [OK]

              Restricted Rights Legend

Use, duplication, or disclosure by the Government is
subject to restrictions as set forth in subparagraph
(c) of the Commercial Computer Software - Restricted
Rights clause at FAR sec. 52.227-19 and subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer
Software clause at DFARS sec. 252.227-7013.

           cisco Systems, Inc.
           170 West Tasman Drive
           San Jose, California 95134-1706



Cisco Internetwork Operating System Software
IOS (tm) 7200 Software (C7200-KBOOT-M), Version 12.2(15)B, EARLY DEPLOYMENT RELEASE SOFTWARE (fc1)
TAC Support: http://www.cisco.com/tac
Copyright (c) 1986-2003 by cisco Systems, Inc.
Compiled Fri 31-Jan-03 04:06 by leccese
Image text-base: 0x60008954, data-base: 0x60984000

cisco 7204 (NPE225) processor (revision A) with 114688K/16384K bytes of memory.
Processor board ID 13252569
R527x CPU at 262Mhz, Implementation 40, Rev 10.0, 2048KB L2 Cache
4 slot midplane, Version 1.0

Last reset from power-on
Bridging software.
X.25 software, Version 3.0.0.
3 FastEthernet/IEEE 802.3 interface(s)
125K bytes of non-volatile configuration memory.

46976K bytes of ATA PCMCIA card at slot 1 (Sector size 512 bytes).
8192K bytes of Flash internal SIMM (Sector size 256K).


Press RETURN to get started!


*Jul 22 19:37:41.887: %LINK-5-CHANGED: Interface FastEthernet0/0, changed state to administratively down
*Jul 22 19:37:41.915: %LINK-3-UPDOWN: Interface FastEthernet1/0, changed state to up
*Jul 22 19:37:41.943: %LINK-3-UPDOWN: Interface FastEthernet2/0, changed state to up
*Jul 22 19:37:42.915: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet1/0, changed state to up
*Jul 22 19:37:42.943: %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet2/0, changed state to up

ssffzz1

保存配置，然后格式化FLASH重新灌个IOS试试，还可以拆掉各个业务板卡再测试。
检查主控板等有无明显物理损坏。


出这种问题能做的也只有这些了。

gdxnfx

这么古老的设备，应该换代了。

Cisco的硬件问题，看你的sn是不是在他列出来的范围内。
http://www.cisco.com/en/US/ts/fn/200/fn25774.html

如果不是，建议把crash文件导出来分析一下,用dir命令看一下最新的crash文件。
多半是内存不好引起。如果有内存条，可以更换一条试一下