- 论坛徽章:
- 0
|
使用了新太阳32M U盘,使用体会!--新太阳USB Storage安装使用
新太阳USB Storage安装使用手册
一、驱动程序安装
1.启动主机进入维护模式:
mount -o lower /dev/cd0 /mnt
cd /mnt/sco
tar xvf drv.tar
2.安装驱动:
cd /tmp/newsun
./install
出现以下界面:
USB Storage Driver Installtion
================================================
1. Install USB Storage Driver
2. Remove USB Storage Driver
================================================
Select an option or enter q to quit:
选择1,安装驱动.
3.安装驱动程序完成后,将自动编译内核:
The UNIX Operating System will now be rebuilt.
This will take a few minutes. Please wait.
Root for this system build is /
The UNIX Kernel has been rebuilt.
Do you want this kernel to boot by default? (y/n)
选择y
Backing up unix to unix.old
Installing new unix on the boot file system
The kernel environment includes device node files and /etc/inittab.
The new kernel may require changes to /etc/inittab or device nodes.
Do you want the kernel environment rebuilt? (y/n)
选择y
重新启动主机。
机器重起后,在初始化时会显示:
%uhci %xxxx-%xxxx -- -- UHCI Driver Ver 1.0,Newsun
也可以用hwconfig命令显示此信息。如果没有出现此信息,
请与新太阳公司联系。
4.安装USB设备:
进入主机维护模式:
mkdev hd 0 SCSI-0 0 hkx 0
You are about to add the following SCSI device:
Type Device Number ID LUN BUS
hkx Sdsk 0 0 0 0
Update SCSI configuration? (y/n)
选择y
重新编译内核
5.重新启动主机后,进入维护模式:
将U盘插入到USB口,如果出现:
NOTICE:USB Storage attached on port *,说明设备连接正常。否则重新插入一次。
mkdev hd 0 SCSI-0 0 hkx 0
出现:
During installation you may choose to overwrite all
Or part of the present content of your hard disk.
Do you wish to continue?(y/n)
选择y
The hard disk installation program will now invoke /etc/fdisk.
Entering 'q' at the following menu will exit /etc/fdisk,
and the hard disk installation will continue.
If you wish to exit the entire installation at this menu,
press the <DEL>; key.
1. Display Partition Table
2. Use Entire Disk for UNIX
3. Use Rest of Disk for UNIX
4. Create UNIX Partition
5. Activate Partition
6. Delete Partition
7. Create Partition
Enter your choice or 'q' to quit:
选择1,可以查看U盘分区信息。
选择Q退出。
WARNING: There is no ACTIVE UNIX partition.
Do you wish to specify an active UNIX partition ?(y/n)
选择n
二、U盘使用说明
1. 将U盘插入到USB口,如果出现:
NOTICE:USB Storage attached on port *,说明设备连接正常。
否则重新插入一次:
mount -o lower /dev/dsk/1s4 /mnt
既可安装U盘到系统中。
2.卸载U盘:
umount /dev/dsk/1s4
三、U盘驱动卸载
1.启动主机进入维护模式:
mount -o lower /dev/cd0 /mnt
cd /mnt/sco
tar xvf drv.tar
2.卸载驱动:
cd /tmp/newsun
./install
出现以下界面:
USB Storage Driver Installtion
================================================
1. Install USB Storage Driver
2. Remove USB Storage Driver
================================================
Select an option or enter q to quit:
选择2,卸载驱动.
3.卸载驱动程序完成后,将自动编译内核:
The UNIX Operating System will now be rebuilt.
This will take a few minutes. Please wait.
Root for this system build is /
The UNIX Kernel has been rebuilt.
Do you want this kernel to boot by default? (y/n)
选择y
Backing up unix to unix.old
Installing new unix on the boot file system
The kernel environment includes device node files and /etc/inittab.
The new kernel may require changes to /etc/inittab or device nodes.
Do you want the kernel environment rebuilt? (y/n)
选择y
重新启动主机。
注意事项:
1.切记!!!,只能在卸载U盘后,才能将U盘拔出,否则会出现严重错误。
2.如果U盘在mount出现:Invalid filesystem 时,将U盘在Window系统中重新格式化一次即可。
U盘备份程序使用说明
一、安装
以超级用户登录:
mount -o lower /dev/cd0 /mnt
cd /安装目录
tar xvf /mnt/sco/usu.tar
二、配置
在运行程序前应正确配置usu.cfg文件中的数据名称。
CX_DB储蓄数据库
DG_DB对公数据库
SH_DB事后数据库
三、运行
将U盘插到USB端口,在出现NOTICE:USB Storage attached on port *后,以超级用户执行./usu,运行本程序。
注意事项:
1.在使用备份程序前应确认U盘已正确连接到USB口。
2.只有在退出备份程序之后,才能将U盘拔出!!!!!!!!!!!
U盘使用、安装FAQ(Frequently Ask Question)
Q1:联想开天系列商用机在Unix下不能使用U盘 ?
A1:联想开天系列商用机中有一款有6个Usb口(2前)因为前两个Usb口与其它硬件共享一个中断,所以在Unix下使用时会有冲突。将U盘插到主机后面的Usb口中即可。
Q2:将U盘插到Usb口中时,在Boot提示符后回车,系统不能启动 ?
A2:将主机CMOS中,从USB设备或软盘启动选项去掉即可。
Q3:联想昭阳笔记本安装驱动正常,但插入U盘时没有提示信息 ?
A3:进入笔记本CMOS中,选择Advanced ,选择I/O Device Configuration,将Infrared Port Enable。
============================================
河北新太阳信息技术有限公司
地址:石家庄市新石北路368号金石工业园 邮编:050091
电话:0311-3811534 3817440 3807440 3852408 传真:0311-3837434
网址:Http://www.nsit.com.cn www.newsun.com.cn
E-Mail:zyl@nsit.com.cn |
|