8.0 xorg桌面起不来，被这个/dev/agpgart晕了

yeahlong

首先，保证内核里头将device agp选了，并且rc.conf也写了
hald_enable="YES"
dbus_enable="YES"
agp_load="YES"
主板集成显卡intel G41
我验证过了，没有/dev/agpgart这个文件
现在运行Xorg -config xorg.conf.new就出错


错误信息
(EE) GARTInit: Unable to open /dev/agpgart (No such file or directory)
(EE) intel(0): /dev/agpgart is either not available, or no memory is available
for allocation.  Please enable agpgart
.(WW) intel(0): VideoRam reduced to 32760 KB (page aligned - was 32763 KB)
(WW) intel(0): DRI2 requires UXA
drmOpenDevice: node name is /dev/dri/card0
Failed to change owner or group for file /dev/dri! 2: No such file or directory
Failed to change owner or group for file /dev/dri/card0! 2: No such file or directory
drmOpenDevice: open result is -1, (No such file or directory)
Failed to change owner or group for file /dev/dri/card0! 2: No such file or directory
drmOpenDevice: open result is -1, (No such file or directory)
drmOpenDevice: Open failed
drmOpenDevice: node name is /dev/dri/card0
Failed to change owner or group for file /dev/dri! 2: No such file or directory
Failed to change owner or group for file /dev/dri/card0! 2: No such file or directory
drmOpenDevice: open result is -1, (No such file or directory)
Failed to change owner or group for file /dev/dri/card0! 2: No such file or directory
drmOpenDevice: open result is -1, (No such file or directory)
drmOpenDevice: Open failed
[drm] failed to load kernel module "i915"
(EE) [drm] drmOpen failed.
(EE) intel(0): [dri] DRIScreenInit failed. Disabling DRI.
(**) intel(0): Framebuffer compression disabled
(**) intel(0): Tiling enabled
(==) intel(0): VideoRam: 32760 KB
(II) intel(0): Attempting memory allocation with tiled buffers.
(EE) intel(0): AGP GART support is either not available or cannot be used.
        Make sure your kernel has agpgart support or has
        the agpgart module loaded.
(II) intel(0): Tiled allocation failed.
(II) intel(0): Attempting memory allocation with untiled buffers.
(EE) intel(0): AGP GART support is either not available or cannot be used.
        Make sure your kernel has agpgart support or has
        the agpgart module loaded.
(II) intel(0): Untiled allocation failed.
(EE) intel(0): Couldn't allocate video memory

Fatal server error:
AddScreen/ScreenInit failed for driver 0


Please consult the The X.Org Foundation support
         at http://wiki.x.org
for help.
Please also check the log file at "/var/log/Xorg.0.log" for additional information.

附件是 xorg.conf.new，Xorg.0.log，内核配置文件


网上搜了不少解决方法，不是内核禁止/打开AGP就是rc.conf加上agp_load="YES"

有什么建议吗？非常感谢！

[ 本帖最后由 yeahlong 于 2009-12-29 22:57 编辑 ]

Iveon

G41很新么？
是为了上分辨率还是跑3D游戏？
你什么主板？我明天去找块来试试。

Iveon

看我的帖子.....

yeahlong

请明示
今晚不搞了 睡觉
内核都编译了2编了
内核加了
device          drm             # DRM core module required by DRM drivers
device          i915drm         # Intel i830 through i915
xorg.cfg中
把Load  "dri"注释了

依然一个报错

macafee

G41太新，应该还不被支持。你可以贴一下dmesg和pciconf -lv。

[ 本帖最后由 macafee 于 2009-12-30 12:21 编辑 ]

yeahlong

我又重装了系统，还是没有/dev/agpgart ，我找了台老的P4 865主板集成显卡的机器装了freebsd8.0 却有/dev/agpgart

下面是G41的dmesg
---------------------------------dmesg-----------------------------------------------------------------------
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-RELEASE #0: Sat Nov 21 15:48:17 UTC 2009
    root@almeida.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Pentium(R) Dual-Core  CPU      E5300  @ 2.60GHz (2599.95-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x1067a  Stepping = 10
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x400e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,XSAVE>
  AMD Features=0x20100000<NX,LM>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant
real memory  = 2147483648 (2048 MB)
avail memory = 1820864512 (1736 MB)
ACPI APIC Table: <DELL   APIC1732>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
cpu0 (BSP): APIC ID:  0
cpu1 (AP): APIC ID:  1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <DELL M09    > on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, 6fd00000 (3) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0xdc00-0xdc07 mem 0xfe400000-0xfe7fffff,0xd0000000-0xdfffffff irq 16 at device 2.0 on pci0
pci0: <multimedia, HDA> at device 27.0 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci1: <ACPI PCI bus> on pcib1
mskc0: <Marvell Yukon 88E8040 Fast Ethernet> port 0xe800-0xe8ff mem 0xfebfc000-0xfebfffff irq 16 at device 0.0 on pci1
msk0: <Marvell Technology Group Ltd. Yukon FE+ Id 0xb8 Rev 0x00> on mskc0
msk0: disabling jumbo frame support
msk0: Ethernet address: 00:ea:01:1c:01:9d
miibus0: <MII bus> on msk0
e1000phy0: <Marvell 88E3016 10/100 Fast Ethernet PHY> PHY 0 on miibus0
e1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
mskc0: [FILTER]
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pci4: <ACPI PCI bus> on pcib4
uhci0: <Intel 82801G (ICH7) USB controller USB-A> port 0xd880-0xd89f irq 23 at device 29.0 on pci0
uhci0: [ITHREAD]
uhci0: LegSup = 0x0f30
usbus0: <Intel 82801G (ICH7) USB controller USB-A> on uhci0
uhci1: <Intel 82801G (ICH7) USB controller USB-B> port 0xd800-0xd81f irq 19 at device 29.1 on pci0
uhci1: [ITHREAD]
uhci1: LegSup = 0x0f30
usbus1: <Intel 82801G (ICH7) USB controller USB-B> on uhci1
uhci2: <Intel 82801G (ICH7) USB controller USB-C> port 0xd480-0xd49f irq 18 at device 29.2 on pci0
uhci2: [ITHREAD]
uhci2: LegSup = 0x0f30
usbus2: <Intel 82801G (ICH7) USB controller USB-C> on uhci2
uhci3: <Intel 82801G (ICH7) USB controller USB-D> port 0xd400-0xd41f irq 16 at device 29.3 on pci0
uhci3: [ITHREAD]
uhci3: LegSup = 0x0f30
usbus3: <Intel 82801G (ICH7) USB controller USB-D> on uhci3
ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xfeaf7c00-0xfeaf7fff irq 23 at device 29.7 on pci0
ehci0: [ITHREAD]
usbus4: EHCI version 1.0
usbus4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0
pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci5: <ACPI PCI bus> on pcib5
isab0: <CI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
atapci1: <Intel ICH7 SATA300 controller> port 0xd080-0xd087,0xd000-0xd003,0xcc00-0xcc07,0xc880-0xc883,0xc800-0xc80f mem 0xfed10000-0xfed103ff irq 19 at device 31.2 on pci0
atapci1: [ITHREAD]
ata2: <ATA channel 0> on atapci1
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci1
ata3: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <ower Button> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
ppc0: <arallel port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppc0: [ITHREAD]
ppbus0: <arallel port bus> on ppc0
plip0: <LIP network interface> on ppbus0
plip0: [ITHREAD]
lpt0: <rinter> on ppbus0
lpt0: [ITHREAD]
lpt0: Interrupt-driven port
ppi0: <arallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 6160d2506000d25
device_attach: est0 attach returned 6
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 6160d2506000d25
device_attach: est1 attach returned 6
p4tcc1: <CPU Frequency Thermal Control> on cpu1
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
md0: Preloaded image </boot/mfsroot> 4423680 bytes at 0xc0f6dfe0usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0

acd0: DVDROM <HP DVD ROM 455d/BH23> at ata0-master UDMA33
ad4: 305245MB <WDC WD3200AAJS-00L7A0 01.03E01> at ata2-master SATA150
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
SMP: AP CPU #1 Launched!
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
Root mount waiting for: usbus4
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub4: 8 ports with 8 removable, self powered
Trying to mount root from ufs:/dev/md0
ugen0.2: <Microsoft> at usbus0
ums0: <Microsoft Basic Optical Mouse, class 0/0, rev 1.10/0.00, addr 2> on usbus0
ums0: 3 buttons and [XYZ] coordinates ID=0
Waiting (max 60 seconds) for system process `vnlru' to stop...done
Waiting (max 60 seconds) for system process `bufdaemon' to stop...done
Waiting (max 60 seconds) for system process `syncer' to stop...
Syncing disks, vnodes remaining...1 0 done
All buffers synced.
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-RELEASE #0: Sat Nov 21 15:48:17 UTC 2009
    root@almeida.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Pentium(R) Dual-Core  CPU      E5300  @ 2.60GHz (2599.96-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x1067a  Stepping = 10
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x400e3bd<SSE3,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,XSAVE>
  AMD Features=0x20100000<NX,LM>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant
real memory  = 2147483648 (2048 MB)
avail memory = 1825062912 (1740 MB)
ACPI APIC Table: <DELL   APIC1732>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
cpu0 (BSP): APIC ID:  0
cpu1 (AP): APIC ID:  1
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <DELL M09    > on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of 0, a0000 (3) failed
acpi0: reservation of 100000, 6fd00000 (3) failed
Timecounter "ACPI-safe" frequency 3579545 Hz quality 850
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x808-0x80b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0xdc00-0xdc07 mem 0xfe400000-0xfe7fffff,0xd0000000-0xdfffffff irq 16 at device 2.0 on pci0
pci0: <multimedia, HDA> at device 27.0 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci1: <ACPI PCI bus> on pcib1
mskc0: <Marvell Yukon 88E8040 Fast Ethernet> port 0xe800-0xe8ff mem 0xfebfc000-0xfebfffff irq 16 at device 0.0 on pci1
msk0: <Marvell Technology Group Ltd. Yukon FE+ Id 0xb8 Rev 0x00> on mskc0
msk0: disabling jumbo frame support
msk0: Ethernet address: 00:ea:01:1c:01:9d
miibus0: <MII bus> on msk0
e1000phy0: <Marvell 88E3016 10/100 Fast Ethernet PHY> PHY 0 on miibus0
e1000phy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
mskc0: [FILTER]
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0
pci2: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 19 at device 28.3 on pci0
pci4: <ACPI PCI bus> on pcib4
uhci0: <Intel 82801G (ICH7) USB controller USB-A> port 0xd880-0xd89f irq 23 at device 29.0 on pci0
uhci0: [ITHREAD]
uhci0: LegSup = 0x0f30
usbus0: <Intel 82801G (ICH7) USB controller USB-A> on uhci0
uhci1: <Intel 82801G (ICH7) USB controller USB-B> port 0xd800-0xd81f irq 19 at device 29.1 on pci0
uhci1: [ITHREAD]
uhci1: LegSup = 0x0f30
usbus1: <Intel 82801G (ICH7) USB controller USB-B> on uhci1
uhci2: <Intel 82801G (ICH7) USB controller USB-C> port 0xd480-0xd49f irq 18 at device 29.2 on pci0
uhci2: [ITHREAD]
uhci2: LegSup = 0x0f30
usbus2: <Intel 82801G (ICH7) USB controller USB-C> on uhci2
uhci3: <Intel 82801G (ICH7) USB controller USB-D> port 0xd400-0xd41f irq 16 at device 29.3 on pci0
uhci3: [ITHREAD]
uhci3: LegSup = 0x0f30
usbus3: <Intel 82801G (ICH7) USB controller USB-D> on uhci3
ehci0: <Intel 82801GB/R (ICH7) USB 2.0 controller> mem 0xfeaf7c00-0xfeaf7fff irq 23 at device 29.7 on pci0
ehci0: [ITHREAD]
usbus4: EHCI version 1.0
usbus4: <Intel 82801GB/R (ICH7) USB 2.0 controller> on ehci0
pcib5: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci5: <ACPI PCI bus> on pcib5
isab0: <CI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH7 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xffa0-0xffaf at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
atapci1: <Intel ICH7 SATA300 controller> port 0xd080-0xd087,0xd000-0xd003,0xcc00-0xcc07,0xc880-0xc883,0xc800-0xc80f mem 0xfed10000-0xfed103ff irq 19 at device 31.2 on pci0
atapci1: [ITHREAD]
ata2: <ATA channel 0> on atapci1
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci1
ata3: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
acpi_button0: <ower Button> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
ppc0: <arallel port> port 0x378-0x37f irq 7 on acpi0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
ppc0: [ITHREAD]
ppbus0: <;Parallel port bus> on ppc0
plip0: <;PLIP network interface> on ppbus0
plip0: [ITHREAD]
lpt0: <;Printer> on ppbus0
lpt0: [ITHREAD]
lpt0: Interrupt-driven port
ppi0: <;Parallel I/O> on ppbus0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 6160d2506000d25
device_attach: est0 attach returned 6
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
est: CPU supports Enhanced Speedstep, but is not recognized.
est: cpu_vendor GenuineIntel, msr 6160d2506000d25
device_attach: est1 attach returned 6
p4tcc1: <CPU Frequency Thermal Control> on cpu1
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounters tick every 1.000 msec
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
acd0: DVDROM <HP DVD ROM 455d/BH23> at ata0-master UDMA33
ad4: 305245MB <WDC WD3200AAJS-00L7A0 01.03E01> at ata2-master SATA150
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
SMP: AP CPU #1 Launched!
Root mount waiting for: usbus4 usbus3 usbus2 usbus1 usbus0
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
Root mount waiting for: usbus4
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub4: 8 ports with 8 removable, self powered
Trying to mount root from ufs:/dev/ad4s1a
ugen0.2: <Microsoft> at usbus0
ums0: <Microsoft Basic Optical Mouse, class 0/0, rev 1.10/0.00, addr 2> on usbus0
ums0: 3 buttons and [XYZ] coordinates ID=0
msk0: link state changed to UP


------------------------------下面是pciconf -lv ------------------------------------------------------------------------



hostb0@pci0:0:0:0:        class=0x060000 card=0x2e308086 chip=0x2e308086 rev=0x03 hdr=0x00
    vendor     = 'Intel Corporation'
    class      = bridge
    subclass   = HOST-PCI
vgapci0@pci0:0:2:0:        class=0x030000 card=0x2e328086 chip=0x2e328086 rev=0x03 hdr=0x00
    vendor     = 'Intel Corporation'
    class      = display
    subclass   = VGA
none0@pci0:0:27:0:        class=0x040300 card=0x10ec0662 chip=0x27d88086 rev=0x01 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801G (ICH7 Family) High Definition Audio'
    class      = multimedia
    subclass   = HDA
pcib1@pci0:0:28:0:        class=0x060400 card=0x10ec0662 chip=0x27d08086 rev=0x01 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801G (ICH7 Family) PCIe Root Port'
    class      = bridge
    subclass   = PCI-PCI
pcib2@pci0:0:28:1:        class=0x060400 card=0x10ec0662 chip=0x27d28086 rev=0x01 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801G (ICH7 Family) PCIe Root Port'
    class      = bridge
    subclass   = PCI-PCI
pcib3@pci0:0:28:2:        class=0x060400 card=0x10ec0662 chip=0x27d48086 rev=0x01 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801G (ICH7 Family) PCIe Root Port'
    class      = bridge
    subclass   = PCI-PCI
pcib4@pci0:0:28:3:        class=0x060400 card=0x10ec0662 chip=0x27d68086 rev=0x01 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801G (ICH7 Family) PCIe Root Port'
    class      = bridge
    subclass   = PCI-PCI
uhci0@pci0:0:29:0:        class=0x0c0300 card=0x27c88086 chip=0x27c88086 rev=0x01 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801G (ICH7 Family) USB Universal Host Controller'
    class      = serial bus
    subclass   = USB
uhci1@pci0:0:29:1:        class=0x0c0300 card=0x27c98086 chip=0x27c98086 rev=0x01 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801G (ICH7 Family) USB Universal Host Controller'
    class      = serial bus
    subclass   = USB
uhci2@pci0:0:29:2:        class=0x0c0300 card=0x27ca8086 chip=0x27ca8086 rev=0x01 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801G (ICH7 Family) USB Universal Host Controller'
    class      = serial bus
    subclass   = USB
uhci3@pci0:0:29:3:        class=0x0c0300 card=0x27cb8086 chip=0x27cb8086 rev=0x01 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801G (ICH7 Family) USB Universal Host Controller'
    class      = serial bus
    subclass   = USB
ehci0@pci0:0:29:7:        class=0x0c0320 card=0x27cc8086 chip=0x27cc8086 rev=0x01 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801G (ICH7 Family) USB 2.0 Enhanced Host Controller'
    class      = serial bus
    subclass   = USB
pcib5@pci0:0:30:0:        class=0x060401 card=0x10ec0662 chip=0x244e8086 rev=0xe1 hdr=0x01
    vendor     = 'Intel Corporation'
    device     = '82801 Family (ICH2/3/4/5/6/7/8/9,63xxESB) Hub Interface to PCI Bridge'
    class      = bridge
    subclass   = PCI-PCI
isab0@pci0:0:31:0:        class=0x060100 card=0x10ec0662 chip=0x27b88086 rev=0x01 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = 'Intel 82801GB/GR (ICH7 Family) LPC Interface Controller - 27B8 (945GL)'
    class      = bridge
    subclass   = PCI-ISA
atapci0@pci0:0:31:1:        class=0x01018a card=0x10ec0662 chip=0x27df8086 rev=0x01 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801G (ICH7 Family) Ultra ATA Storage Controller'
    class      = mass storage
    subclass   = ATA
atapci1@pci0:0:31:2:        class=0x01018f card=0x10ec0662 chip=0x27c08086 rev=0x01 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801GB/GR/GH (ICH7 Family) Serial ATA Storage Controller'
    class      = mass storage
    subclass   = ATA
none1@pci0:0:31:3:        class=0x0c0500 card=0x10ec0662 chip=0x27da8086 rev=0x01 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801G (ICH7 Family) SMBus Controller'
    class      = serial bus
    subclass   = SMBus
mskc0@pci0:1:0:0:        class=0x020000 card=0x80401afa chip=0x435411ab rev=0x13 hdr=0x00
    vendor     = 'Marvell Semiconductor (Was: Galileo Technology Ltd)'
    device     = 'Marvell Yukon 88E8040 PCI-E Fast Ethernet Controller (88E8040)'
    class      = network
    subclass   = ethernet

[ 本帖最后由 yeahlong 于 2009-12-30 22:08 编辑 ]

yeahlong

看来是内核不支持了G41显卡
也难怪bsd本来就没打算在桌面有大发展

macafee

G41太新，看来只有上CURRENT版本看看了。

Iveon

我查看了源码，有对G45的支持，确实没有G41。
我为你编译了一个，你测试一下。

1. 
   
2. tar -zxxf i915.tar.gz
   
3. cp i915/* /boot/kernel/
   
4. kldload i915
   
5. 进x试试
   

复制代码

[ 本帖最后由 Iveon 于 2010-1-1 00:46 编辑 ]

yeahlong

原帖由 Iveon 于 2009-12-31 22:57 发表
.....之前没有看你的dmesg，
你又没有想过865的时候还没有PCI-E？
你是不是还在用N年的方法，
配置N年以后的FreeBSD和N年以后更新换代了的硬件呢？
编译内核是在无法驱动的时候再去尝试的底层硬件的支持方式 ...

不好意思，我也是刚开始弄bsd自己玩玩，从零开始看官方文档看不进去，自己找个项目（起下桌面）试试看也能提高下自己，所以网上找类似的解决方法，有些人说要重新编译内核加上865drm，所以我也就试试看了，我是有病乱吃药，呵呵。
G41是昂达g41c

贴下 865g主板的dmege,能准确显示显卡类型


----------------------------------------------------------dmege--------------------------------------------------------------------------------

Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-RELEASE #0: Sat Nov 21 15:48:17 UTC 2009
    root@almeida.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz (2793.19-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf29  Stepping = 9
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x4400<CNXT-ID,xTPR>
real memory  = 536870912 (512 MB)
avail memory = 501850112 (478 MB)
ACPI APIC Table: <PTLTD           APIC  >
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <PTLTD   RSDT> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x1008-0x100b on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0x1800-0x1807 mem 0xf0000000-0xf7ffffff,0xe8000000-0xe807ffff irq 16 at device 2.0 on pci0
agp0: <Intel 82865G (865G GMCH) SVGA controller> on vgapci0
agp0: detected 8060k stolen memory
agp0: aperture size is 128M
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0x1820-0x183f irq 16 at device 29.0 on pci0
uhci0: [ITHREAD]
uhci0: LegSup = 0x003b
usbus0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0x1840-0x185f irq 19 at device 29.1 on pci0
uhci1: [ITHREAD]
uhci1: LegSup = 0x0010
usbus1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0x1860-0x187f irq 18 at device 29.2 on pci0
uhci2: [ITHREAD]
uhci2: LegSup = 0x0010
usbus2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0x1880-0x189f irq 16 at device 29.3 on pci0
uhci3: [ITHREAD]
uhci3: LegSup = 0x0010
usbus3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
ehci0: <Intel 82801EB/R (ICH5) USB 2.0 controller> mem 0xe8080000-0xe80803ff irq 23 at device 29.7 on pci0
ehci0: [ITHREAD]
usbus4: EHCI version 1.0
usbus4: <Intel 82801EB/R (ICH5) USB 2.0 controller> on ehci0
pcib1: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci3: <ACPI PCI bus> on pcib1
em0: <Intel(R) PRO/1000 Network Connection 6.9.14> port 0x2000-0x203f mem 0xe8100000-0xe811ffff irq 16 at device 11.0 on pci3
em0: [FILTER]
em0: Ethernet address: 00:0d:60:68:e8:d6
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH5 UDMA100 controller> port 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1810-0x181f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci0
ata0: [ITHREAD]
ata1: <ATA channel 1> on atapci0
ata1: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
pci0: <multimedia, audio> at device 31.5 (no driver attached)
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz0: _CRT value is absurd, ignored (6280.3C)
acpi_button0: <Power Button> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x71 irq 8 on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: [GIANT-LOCKED]
psm0: [ITHREAD]
psm0: model IntelliMouse, device ID 3
fdc0: <floppy drive controller> port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on acpi0
fdc0: [FILTER]
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart1: [FILTER]
ppc0: <Parallel port> port 0x378-0x37f,0x778-0x77f irq 7 drq 3 on acpi0
ppc0: SMC-like chipset (ECP/EPP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppc0: [ITHREAD]
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
plip0: [ITHREAD]
lpt0: <Printer> on ppbus0
lpt0: [ITHREAD]
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
cpu0: <ACPI CPU> on acpi0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
pmtimer0 on isa0
orm0: <ISA Option ROMs> at iomem 0xca800-0xcb7ff,0xcb800-0xcc7ff,0xe0000-0xeffff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 2793193164 Hz quality 800
Timecounters tick every 1.000 msec
usbus0: 12Mbps Full Speed USB v1.0
usbus1: 12Mbps Full Speed USB v1.0
usbus2: 12Mbps Full Speed USB v1.0
usbus3: 12Mbps Full Speed USB v1.0
usbus4: 480Mbps High Speed USB v2.0
ad0: 38162MB <Seagate ST340014A 8.10> at ata0-master UDMA100
ugen0.1: <Intel> at usbus0
uhub0: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus1
ugen2.1: <Intel> at usbus2
uhub2: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus2
ugen3.1: <Intel> at usbus3
uhub3: <Intel UHCI root HUB, class 9/0, rev 1.00/1.00, addr 1> on usbus3
ugen4.1: <Intel> at usbus4
uhub4: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus4
acd0: CDROM <LTN486S/YUS8> at ata1-master UDMA33
uhub0: 2 ports with 2 removable, self powered
uhub1: 2 ports with 2 removable, self powered
uhub2: 2 ports with 2 removable, self powered
uhub3: 2 ports with 2 removable, self powered
Root mount waiting for: usbus4
Root mount waiting for: usbus4
Root mount waiting for: usbus4
uhub4: 8 ports with 8 removable, self powered
Trying to mount root from ufs:/dev/ad0s1a
em0: link state changed to UP
pid 21872 (conftest), uid 0: exited on signal 11 (core dumped)

[ 本帖最后由 yeahlong 于 2010-1-1 00:04 编辑 ]