论坛徽章:: 0

电梯直达

1楼 [收藏(0)] [报告]

发表于 2010-07-10 18:53 |只看该作者 |倒序浏览

我有一台N1290开始是机器FT0有点问题，更换FT0后，把机器加电起来发现机器故障灯亮，showboard看系统指示灯板degrade， fan3状态不对，我是想把SIB更换了，但是怕更换了故障灯还是亮的，不知道这个SIB是否也可以在service下置为ok？
不知道大家有没有遇到这样的情况

lom>
lom>showboards

Slot    Pwr Component Type                State    Status
----    --- --------------                -----    ------
SSC1    On  System Controller V2          Main    Passed
/N0/SCC  - System Config Card          Assigned OK
/N0/BP - Baseplane                   Assigned Passed
/N0/SIB  - Indicator Board             Assigned Degraded
/N0/SPDB - System Power Distribution Bd.  Assigned Passed
/N0/PS0  On  D142 Power Supply             -       OK
/N0/PS1  On  D142 Power Supply             -       OK
/N0/PS2  On  D142 Power Supply             -       OK
/N0/PS3  On  D142 Power Supply             -       OK
/N0/FT0  On  Fan Tray                      High Speed Passed
/N0/RP0  On  Repeater Board                Assigned OK
/N0/RP2  On  Repeater Board                Assigned OK
/N0/SB0  On  CPU Board V3                Active    Passed
/N0/SB2  On  CPU Board V3                Active    Passed
/N0/IB6  On  PCI+ I/O Board                Active    Passed
/N0/MB - Media Bay                   Assigned Passed

lom>showenvironment -v

Slot Device    Sensor    Min LoWarn Value  HiWarn Max Units    Age    Status
------- ---------- ------------ ------ ------ ------ ------ ------ --------- ------- ------
SSC1 SBBC 0    Temp. 0       -12    -2 45       102 107 Degrees C 4 sec OK
SSC1 CBH 0    Temp. 0       -12    -2 50       102 107 Degrees C 4 sec OK
SSC1 Board 0 Temp. 0       -12    -2 33       82    87 Degrees C 4 sec OK
SSC1 Board 0 Temp. 1       -12    -2 32       82    87 Degrees C 4 sec OK
SSC1 Board 0 Temp. 2       -12    -2 38       82    87 Degrees C 4 sec OK
SSC1 Board 0 1.5 VDC 0    1.35 1.42 1.52    1.57 1.65 Volts DC 4 sec OK
SSC1 Board 0 3.3 VDC 0    2.97 3.13 3.33    3.46 3.63 Volts DC 4 sec OK
SSC1 Board 0 5 VDC 0       4.50 4.75 4.95    5.25 5.50 Volts DC 4 sec OK
/N0/PS0 Input 0 Volt. 0          -    - -          -    - -          2 sec OK
/N0/PS0 48 VDC 0 Volt. 0    40.00  40.00 48.00 60.00  60.00 Volts DC 2 sec OK
/N0/PS1 Input 0 Volt. 0          -    - -          -    - -          1 sec OK
/N0/PS1 48 VDC 0 Volt. 0    40.00  40.00 48.00 60.00  60.00 Volts DC 1 sec OK
/N0/PS2 Input 0 Volt. 0          -    - -          -    - -          2 sec OK
/N0/PS2 48 VDC 0 Volt. 0    40.00  40.00 48.00 60.00  60.00 Volts DC 2 sec OK
/N0/PS3 Input 0 Volt. 0          -    - -          -    - -          1 sec OK
/N0/PS3 48 VDC 0 Volt. 0    40.00  40.00 48.00 60.00  60.00 Volts DC 1 sec OK
/N0/FT0 Fan 3    Cooling 0                ????                            1 hrs failed
/N0/FT0 Fan 0    Cooling 0                Auto                            1 sec OK
/N0/FT0 Fan 1    Cooling 0                Auto                            1 sec OK
/N0/FT0 Fan 2    Cooling 0                Auto                            1 sec OK
/N0/FT0 Fan 4    Cooling 0                Auto                            1 sec OK
/N0/FT0 Fan 5    Cooling 0                Auto                            1 sec OK
/N0/FT0 Fan 6    Cooling 0                Auto                            1 sec OK
/N0/FT0 Fan 7    Cooling 0                Auto                            2 sec OK

文库|博客

huilin006

白手起家

论坛徽章:: 0

2楼 [报告]

发表于 2010-07-10 19:34 |只看该作者

补充一下，prtdiag显示fan3状态和速度没有显示出来，但FAN3 fru状态是ok的，把老的风扇上拆下好的风扇单独更换FAN3，FAN3状态还是为hrs failed，然后把原来老的FT0换回去，状态依旧，我打算还是先把FT0再换一个，如果故障灯还是亮的话，再把SIB换了。

prtdiag -v
=============================== Environmental Status ===============================
Fan Speeds:
---------------------------------------------
Location    Sensor       Status Speed
---------------------------------------------
FT0/FAN3    ft_fan3
FT0/FAN0    ft_fan0       self-regulating
FT0/FAN1    ft_fan1       self-regulating
FT0/FAN2    ft_fan2       self-regulating
FT0/FAN4    ft_fan4       self-regulating
FT0/FAN5    ft_fan5       self-regulating
FT0/FAN6    ft_fan6       self-regulating
FT0/FAN7    ft_fan7       self-regulating
IB6/FAN0    ft_fan0       okay    100%
IB6/FAN1    ft_fan1       okay    100%

--------------------------------------------------
Led State:
--------------------------------------------------
Location Led                State    Color
--------------------------------------------------
   - fault                ON       amber
   - power                ON       green
   - locator             OFF       white
   - top_access          ON       amber
   - alarm1             OFF       amber
   - alarm2             OFF       amber
   - system             OFF       green
   - supplyA             OFF       green
   - supplyB             OFF       green
============================== FRU Operational Status ==============================
-------------------------
Fru Operational Status:
-------------------------
Location       Status
-------------------------
PS0          okay
PS1          okay
PS2          okay
PS3          okay
FT0          okay
FT0/FAN3       okay
FT0/FAN0       okay
FT0/FAN1       okay
FT0/FAN2       okay
FT0/FAN4       okay
FT0/FAN5       okay
FT0/FAN6       okay
FT0/FAN7       okay