IPMP奇怪问题，大家帮忙看下

gwl48

4台T5120，solairs10系统，e1000g0,e1000g配置1IPMP后，第一次拔g0口，浮动IP成功飘过去，然后插入G0网线，浮动IP无法飘回G0上,
root@HB01-DNS-SV01 # ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
        inet 127.0.0.1 netmask ff000000
e1000g0: flags=19000802<BROADCAST,MULTICAST,IPv4,NOFAILOVER,FAILED> mtu 0 index 2
        inet 0.0.0.0 netmask 0
        groupname ipmp
        ether 0:21:28:3a:fa:3e
e1000g0:1: flags=19040803<UP,BROADCAST,MULTICAST,DEPRECATED,IPv4,NOFAILOVER,FAILED> mtu 1500 index 2
        inet 192.168.100.1 netmask ffffff00 broadcast 192.168.100.255
e1000g1: flags=29040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER,STANDBY> mtu 1500 index 3
        inet 192.168.100.2 netmask ffffff00 broadcast 192.168.100.255
        groupname ipmp
        ether 0:21:28:3a:fa:3f
e1000g1:1: flags=21000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4,STANDBY> mtu 1500 index 3
        inet 192.168.100.3 netmask ffffff00 broadcast 192.168.100.255

重启后发现检测到 e1000g1 坏，进行系统后会ping通1-2次后就不通了.多次重启一样.用g2和g3做IPMP现象一样，显示备网卡failed.单独给4个网卡配IP正常.现网络架构是T5120接两台H3交换机，交换机配VLAN，网关是交换机.先怀疑是交换机问题，但单独拿cisco2950或dlink的小交换机接G0和G1口，笔记本当网关，问题依旧。大家帮我看看！硬件应该没问题.
29 20:04:47 in.mpathd[239]: NIC failure detected on e1000g1 of group sc_ipmp0
Jul 29 20:04:47 in.mpathd[239]: Successfully failed over from NIC e1000g1 to NIC e1000g0

bash-3.00# ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
        inet 127.0.0.1 netmask ff000000
e1000g2: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
        inet 192.168.100.6 netmask ffffff00 broadcast 192.168.100.255
        groupname sc_ipmp0
        ether 0:21:28:3a:fa:36
e1000g2:1: flags=9040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER> mtu 1500 index 2
        inet 192.168.100.5 netmask ffffff00 broadcast 192.168.100.255
e1000g3: flags=19040843<UP,BROADCAST,RUNNING,MULTICAST,DEPRECATED,IPv4,NOFAILOVER,FAILED> mtu 1500 index 3
        inet 192.168.100.4 netmask ffffff00 broadcast 192.168.100.255
        groupname sc_ipmp0
        ether 0:21:28:3a:fa:37Jul

bash-3.00# more /etc/host*
::::::::::::::
/etc/hostname.e1000g0
::::::::::::::
HB01-DNS-SV01 group ipmp netmask + broadcast + up \
addif HB01-DNS-SV01-e1000g0-test -failover deprecated netmask + broadcast + up
::::::::::::::
/etc/hostname.e1000g1
::::::::::::::
HB01-DNS-SV01-e1000g1-test group ipmp -failover deprecated standby netmask + broadcast + up
::::::::::::::
/etc/hosts
::::::::::::::
#
# Internet host table
#
::1     localhost      
127.0.0.1       localhost      
192.168.100.3   HB01-DNS-SV01   HB01-DNS-SV01.  loghost
192.168.100.1   HB01-DNS-SV01-e1000g0-test      
192.168.100.2   HB01-DNS-SV01-e1000g1-test

unixsoft

查看一下 default router 还在么？

unixsoft

netstat -rn

gwl48

回复 3# unixsoft


    网关有，192.168.100.254，设置同网段其他机器IP，也是一样的效果

aping2005

你装的是不是Solaris 10 U8?
如果是，请升级Kernel patch到较新版本，这是一个bug
Sun 的研发啊...

gwl48

你装的是不是Solaris 10 U8?
如果是，请升级Kernel patch到较新版本，这是一个bug
Sun 的研发啊...
aping2005 发表于 2010-07-30 16:31

    已解决，使用link_base实现IPMP就OK了，配置如下：

root@HB01-DNS-SV02 # more /etc/host*
::::::::::::::
/etc/hostname.e1000g0
::::::::::::::
HB01-DNS-SV02 netmask + broadcast + group ipmp_group0 up
::::::::::::::
/etc/hostname.e1000g1
::::::::::::::
HB01-DNS-SV02-TEST1 netmask + broadcast + group ipmp_group0 up
::::::::::::::
/etc/hosts
::::::::::::::
#
# Internet host table
#
::1     localhost      
127.0.0.1       localhost      
192.168.100.6   HB01-DNS-SV02   loghost
#192.168.100.5  HB01-DNS-SV02-TEST0
192.168.100.4   HB01-DNS-SV02-TEST1

yuhuohu

很有借鉴意义