在进行make_tape_recovery恢复时，未完成，重启后，系统疯了

jcbut2008

系统不断报警，不知大家有没有遇到过。
报警信息如下：
************* SYSTEM ALERT **************
SYSTEM NAME: Admin
DATE: 08/23/2010 TIME: 13:47:24
ALERT LEVEL: 6 = Boot possible, pending failure - action required

REASON FOR ALERT
SOURCE: 4 = power
SOURCE DETAIL: 4 = high voltage DC power   SOURCE ID: 0
PROBLEM DETAIL: A = failed or disconnected

LEDs:  RUN      ATTENTION     FAULT     REMOTE     POWER
       FLASH    FLASH         OFF       ON         ON
LED State: Running non-OS code.  Non-critical error detected.
Check Chassis and Console Logs for error messages.

0x0020006A4400404F 00000000 00000000 - type  0 = Data Field Unused
0x5820086A4400404F 00006E07 170D2F18 - type 11 = Timestamp 08/23/2010 13:47:24
A: ack read of this entry - X: Disable all future alert messages
Anything else skip redisplay the log entry
->Choice:*
*****************************************

************* SYSTEM ALERT **************
SYSTEM NAME: Admin
DATE: 08/23/2010 TIME: 13:47:24
ALERT LEVEL: 6 = Boot possible, pending failure - action required

REASON FOR ALERT
SOURCE: 4 = power
SOURCE DETAIL: 4 = high voltage DC power   SOURCE ID: 0
PROBLEM DETAIL: A = failed or disconnected

LEDs:  RUN      ATTENTION     FAULT     REMOTE     POWER
       FLASH    FLASH         OFF       ON         ON
LED State: Running non-OS code.  Non-critical error detected.
Check Chassis and Console Logs for error messages.

0x0020006A4400404F 00000000 00000000 - type  0 = Data Field Unused
0x5820086A4400404F 00006E07 170D2F18 - type 11 = Timestamp 08/23/2010 13:47:24
A: ack read of this entry - X: Disable all future alert messages
Anything else skip redisplay the log entry
->Choice:*
*****************************************

************* SYSTEM ALERT **************
SYSTEM NAME: Admin
DATE: 08/23/2010 TIME: 13:47:24
ALERT LEVEL: 6 = Boot possible, pending failure - action required

REASON FOR ALERT
SOURCE: 4 = power
SOURCE DETAIL: 4 = high voltage DC power   SOURCE ID: 0
PROBLEM DETAIL: A = failed or disconnected

LEDs:  RUN      ATTENTION     FAULT     REMOTE     POWER
       FLASH    FLASH         OFF       ON         ON
LED State: Running non-OS code.  Non-critical error detected.
Check Chassis and Console Logs for error messages.

0x0020006A4400404F 00000000 00000000 - type  0 = Data Field Unused
0x5820086A4400404F 00006E07 170D2F18 - type 11 = Timestamp 08/23/2010 13:47:24
A: ack read of this entry - X: Disable all future alert messages
Anything else skip redisplay the log entry
->Choice:
*****************************************

rfancy

检查eventlog，MP log，看报错是供电出问题了

REASON FOR ALERT
SOURCE: 4 = power
SOURCE DETAIL: 4 = high voltage DC power   SOURCE ID: 0
PROBLEM DETAIL: A = failed or disconnected

tangye

再恢复一遍

jcbut2008

以上报错还是没有恢复完全造成的（一次恢复竟然要2个多小时，不知有没有比我这更长的）。楼上正解。

wuzi1006

有短有长，看跟盘原来内容是什么，我见过备份要10几个小时的

michael1983

看报错是电有问题
把电压稳定了先