论坛徽章:: 0

电梯直达

1楼 [收藏(0)] [报告]

发表于 2011-01-04 10:21 |只看该作者 |倒序浏览

本帖最后由 kylinlt 于 2011-01-04 10:31 编辑

最近客户磁带备份出错，看到信息中错误信息是CPF5349，然后提示的是CPP630C，我就测试了一下，建立了一个TEST LIB，进行手动备份，正常，然后通过WRKJOBSCDE设置备份，也正常，但是等到晚上备份的时候，又提示错误。很是郁闷，请高手帮我分析下，到底是磁带问题，还是本身磁带机出问题了？

环境：I515，通过磁带机设置WRKJOBSCDE进行备份。
   中午时分，备份TEST LIB 成功。这个TEST LIB中没有任何数据。
   晚上，备份客户数据，开始报错。
   再磁带备份失败的第一天，再SAL里面出现了SRC 63A09350的记录。

分析：如果说是磁带机问题，我通过手动和后台备份两种方式，都成功备份了TEST这个LIB.
      如果说是磁带问题，为何备份用户数据LIB的时候，又总是报错呢？
这里寻求大家支持，谢谢。

文库|博客

tomroom

丰衣足食

论坛徽章:: 1

2楼 [报告]

发表于 2011-01-04 13:12 |只看该作者

你可以查询系统信息，这个msn提示介质有问题：有可能是你磁带头需要清理或者磁带或者驱动器是否偶问题

Message ID  Severity  Message Text
  CPF5349    60    Media error on volume &8 on device &4.

                     Display Formatted Message Text
                                                         System: B0001BD5
Message ID . . . . . . . . . : CPF5349
Message file . . . . . . . . : QCPFMSG
Library  . . . . . . . . . :    QSYS

Message . . . . : Media error on volume &8 on device &4.
Cause . . . . . : A tape media error occurred while processing file &2 in
library &3.
Recovery  . . . : Clean the tape path and heads.  Then try again.
   -- If the error continues to occur during output operation, load another
volume and try again.
   -- If the error occurs during an input operation, try using another
device.
   -- If the error persists, use another volume and create the input files
again.
Technical description . . . . . . . . : The tape may contain data written in
a density the device does not support. Error Log ID &22.

                                                                     Bottom
Press Enter to continue.

F3=Exit F11=Display unformatted message text F12=Cancel
Already at top of area.

实战分享：从技术角度谈机器学习入门| 【大话IT】RadonDB低门槛向MySQL集群下战书 | ChinaUnix打赏功能已上线！ | 新一代分布式关系型数据库RadonDB知多少？

tomroom

丰衣足食

论坛徽章:: 1

3楼 [报告]

发表于 2011-01-04 13:13 |只看该作者

看你是用磁带库还是用磁带机发起备份

实战分享：从技术角度谈机器学习入门| 【大话IT】RadonDB低门槛向MySQL集群下战书 | ChinaUnix打赏功能已上线！ | 新一代分布式关系型数据库RadonDB知多少？

tomroom

丰衣足食

论坛徽章:: 1

4楼 [报告]

发表于 2011-01-04 13:35 |只看该作者

These SRCs start with 6.
SRC What it means

63xx xxxx A tape unit failed. See Recovering from a tape or optical device problem

Recovering from a tape or optical device problem
To resolve tape or optical device problems, follow this procedure.

Verify the following aspects:

•All tapes or optical devices are powered on and in a Ready (enabled) condition.
•Cables between the system and the tape or optical device are correctly connected (if applicable).
•Tape density and tape bits per inch (BPI) match.
•The tape path is cleaned.
•The CD disk is clean, the format is supported, and the disk is loaded correctly with the label side showing.
Do all the tapes or CD device fail to read or write?
•Yes: Contact your hardware service provider.
•No: Replace the tape or CD and try the operation again. If the same failure occurs, contact your hardware service provider.
Parent topic: Problem analysis procedures