论坛徽章:: 0

电梯直达

1楼 [收藏(0)] [报告]

发表于 2009-12-11 15:32 |只看该作者 |倒序浏览

感谢大家的帮忙。我的DNW终于有信息输出了，内核也启动了  不过启动到
TCP cubic registered
NET: Registered protocol family 1

就没有下文了，怎么不提示我挂载文件系统呢。。。。
还有中间很多usb 1-2: device not accepting address 4, error -62错误，怎么解决~？
下面是我的串口输出~

## Booting image at 32000000 ...
  Image Name:  ARM
  Created:    2009-12-11  5:01:40 UTC
  Image Type:  ARM Linux Kernel Image (gzip compressed)
  Data Size: 1849639 Bytes =  1.8 MB
  Load Address: 30008000
  Entry Point:  30008000
  Verifying Checksum ... OK
  Uncompressing Kernel Image ... OK

Starting kernel ...

Linux version 2.6.22.6 (book@localhost.localdomain) (gcc version 3.4.5) #16 Fri Dec 11 12:59:45 CST 2009
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0003177
Machine: SMDK2440
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C244X: core 399.651 MHz, memory 99.912 MHz, peripheral 49.956 MHz
S3C24XX Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (2.116 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists.  Total pages: 16256
Kernel command line: root=/dev/mtdblock1 ip=192.168.10.21:192.168.10.10:192.168.10.1:255.255.255.0::eth0ff ethaddr=11:22:33:44:55:66 noinitrd console=ttySAC1,115200n81
irq: clearing subpending status 00000010
PID hash table entries: 256 (order: 8, 1024 bytes)
timer tcon=00500000, tcnt a29d, tcfg 00000200,00000000, usec 00001ebf
Console: colour dummy device 80x30
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 60964KB available (3272K code, 468K data, 144K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
S3C2410 Power Management, (c) 2004 Simtec Electronics
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C2440: Clock Support, DVS off
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4800000, irq 33
DMA channel 1 at c4800040, irq 34
DMA channel 2 at c4800080, irq 35
DMA channel 3 at c48000c0, irq 36
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 204

TCP reno registered
NetWinder Floating Point Emulator V0.97 (double precision)
Registering GDB sysrq handler
JFFS2 version 2.2. (NAND) 漏 2001-2006 Red Hat, Inc.
yaffs Dec 1 2009 15:21:11 Installing.
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Console: switching to colour frame buffer device 30x40
fb0: s3c2410fb frame buffer device
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
s3c2440-uart.0: s3c2410_serial0 at MMIO map 0x50000000 mem 0xf0400000 (irq = 70) is a S3C2440
s3c2440-uart.1: s3c2410_serial1 at MMIO map 0x50004000 mem 0xf0404000 (irq = 73) is a S3C2440
s3c2440-uart.2: s3c2410_serial2 at MMIO map 0x50008000 mem 0xf0408000 (irq = 76) is a S3C2440
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
loop: module loaded
cs89x0:cs89x0_probe(0x0)
cs89x0: no cs8900 or cs8920 detected. Be sure to disable PnP with SETUP
dm9000 Ethernet Driver
eth0: dm9000 at c486a000,c486c004 IRQ 51 MAC: 08:00:3e:26:0a:5b
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
hda: probing with STATUS(0xa0) instead of ALTSTATUS(0x0a)
hda: probing with STATUS(0xa1) instead of ALTSTATUS(0x0a)
hda: no response (status = 0xa1), resetting drive
hdb: probing with STATUS(0xb0) instead of ALTSTATUS(0x0a)
hdb: probing with STATUS(0xa1) instead of ALTSTATUS(0x0a)
hdb: no response (status = 0xa1), resetting drive
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2440-nand s3c2440-nand: Tacls=2, 20ns Twrph0=6 60ns, Twrph1=2 20ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
Scanning device for bad blocks
Creating 3 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00200000 : "kernel"
0x00200000-0x00a00000 : "jffs2"
0x00a00000-0x04000000 : "yaffs"
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
Initializing USB Mass Storage driver...
usb 1-2: new full speed USB device using s3c2410-ohci and address 2
usb 1-2: device descriptor read/64, error -62
usb 1-2: device descriptor read/64, error -62
usb 1-2: new full speed USB device using s3c2410-ohci and address 3
usb 1-2: device descriptor read/64, error -62
usb 1-2: device descriptor read/64, error -62
usb 1-2: new full speed USB device using s3c2410-ohci and address 4
usb 1-2: device not accepting address 4, error -62
usb 1-2: new full speed USB device using s3c2410-ohci and address 5
usb 1-2: device not accepting address 5, error -62
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
s3c2440-i2c s3c2440-i2c: slave address 0x10
s3c2440-i2c s3c2440-i2c: bus frequency set to 390 KHz
s3c2440-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
mapped channel 0 to 0
s3c2440-sdi s3c2440-sdi: powered down.
s3c2440-sdi s3c2440-sdi: initialisation done.
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
NET: Registered protocol family 1