- 论坛徽章:
- 0
|
U-Boot 1.1.6 (Dec 23 2008 - 18:36:21)
U-Boot code: 33F80000 -> 33F987D0 BSS: -> 33F9CF44
DRAM: 64 MB
NAND: 64 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
NAND read: device 0 offset 1048576, size 3145728 ...
3145728 bytes read: OK
## Booting image at 30007fc0 ...
Image Name: Linux-2.6.14
Created: 2009-06-14 8:43:21 UTC
Image Type: ARM Linux Kernel Image (uncompressed)
Data Size: 1183884 Bytes = 1.1 MB
Load Address: 30008000
Entry Point: 30008000
Verifying Checksum ... OK
OK
Starting kernel ...
Uncompressing Linux.............................................................................. done, booting the kernel.
Linux version 2.6.14 (root@zheng) (gcc version 3.4.1) #19 Thu Jun 11 11:21:49 CST 2009
CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)
Machine: SMDK2410
Memory policy: ECC disabled, Data cache writeback
CPU S3C2410A (id 0x32410002)
S3C2410: core 200.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
S3C2410 Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
USB Control, (c) 2006 s3c2410
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists
Kernel command line: noinitrd console=ttySAC0,115200 root=/dev/mtdblock2 init=/linuxrc mem=64M
irq: clearing subpending status 00000002
PID hash table entries: 512 (order: 9, 8192 bytes)
timer tcon=00500000, tcnt a2c1, tcfg 00000200,00000000, usec 00001eb8
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 62336KB available (1985K code, 417K data, 92K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
softlockup thread 0 started up.
NET: Registered protocol family 16
S3C2410: Initialising architecture
SCSI subsystem initialized
usbcore: registered new driver usbfs
usbcore: registered new driver hub
S3C2410 DMA Driver, (c) 2003-2004 Simtec Electronics
DMA channel 0 at c4800000, irq 33
DMA channel 1 at c4800040, irq 34
DMA channel 2 at c4800080, irq 35
DMA channel 3 at c48000c0, irq 36
NetWinder Floating Point Emulator V0.97 (double precision)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
yaffs Jun 3 2009 20:17:26 Installing.
Console: switching to colour frame buffer device 80x30
fb0: s3c2410fb frame buffer device
fb1: Virtual frame buffer device, using 1024K of video memory
S3C2410 RTC, (c) 2004 Simtec Electronics
s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2410
s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2410
s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2410
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Cirrus Logic CS8900A driver for Linux (Modified for SMDK2410)
: CS8900A rev E at 0xe0000300 irq=52, no eeprom , addr: 08: 0:3E:26:0A:5B
Linux video capture interface: v1.00
V4L-Driver for Vision CPiA based cameras v1.2.3
Since in-kernel colorspace conversion is not allowed, it is disabled by default now. Users should fix the applications in case they don't work without conversion reenabled by setting the 'colorspace_conv' module parameter to 1<6>USB driver for Vision CPiA based cameras v1.2.3
usbcore: registered new driver cpia
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2410-nand: mapped registers at c4980000
s3c2410-nand: timing: Tacls 10ns, Twrph0 40ns, Twrph1 10ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bit)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Bad eraseblock 2627 at 0x0290c000
Creating 4 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00100000 : "bootloader"
0x00100000-0x00400000 : "kernel"
0x00400000-0x02c00000 : "root"
0x02d00000-0x03c00000 : "user"
usbmon: debugfs is not available
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver ov511
drivers/usb/media/ov511.c: v1.64 for Linux 2.5 : ov511 USB Camera Driver
drivers/usb/media/se401.c: SE401 usb camera driver version 0.24 registering
usbcore: registered new driver se401
mice: PS/2 mouse device common for all mice
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
Reading data from NAND FLASH without ECC is not recommended
yaffs: dev is 32505858 name is "mtdblock2"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.2, "mtdblock2"
block 2372 is bad
VFS: Mounted root (yaffs filesystem).
mount_devfs_fs(): unable to mount devfs, err: -2
Freeing init memory: 92K
Warning: unable to open an initial console.
Failed to execute /linuxrc. Attempting defaults...
Kernel panic - not syncing: No init found. Try passing init= option to kernel.
yaffs文件系统启动失败，但换成cramfs就成功启动，请高手解答，谢谢！ |
|
免费注册
发表于 2009-06-15 14:54
