- 论坛徽章:
- 0
|
Linux version 2.6.28.7 (root@Kevin-Linux) (gcc version 3.4.1) #1 Tue Apr 14 20:30:45 CST 2009
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: Atmel AT91RM9200
Memory policy: ECC disabled, Data cache writeback
Clocks: CPU 179 MHz, master 59 MHz, main 18.432 MHz
Built 1 zonelists in Zone order, mobility grouping off. Total pages: 4064
Kernel command line: root=/dev/ram rw initrd=0x20a00000,6000000 ramdisk_size=4096 console=ttyS0,115200 mem=16M
AT91: 128 gpio irqs in 4 banks
PID hash table entries: 64 (order: 6, 256 bytes)
Console: colour dummy device 80x30
console [ttyS0] enabled
Dentry cache hash table entries: 2048 (order: 1, 8192 bytes)
Inode-cache hash table entries: 1024 (order: 0, 4096 bytes)
Memory: 16MB = 16MB total
Memory: 7592KB available (2432K code, 202K data, 112K init)
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop... 89.79 BogoMIPS (lpj=35020
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
net_namespace: 288 bytes
NET: Registered protocol family 16
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 512 (order: 0, 4096 bytes)
TCP bind hash table entries: 512 (order: -1, 2048 bytes)
TCP: Hash tables configured (established 512 bind 512)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 5859K
NetWinder Floating Point Emulator V0.97 (double precision)
msgmni has been set to 26
io scheduler noop registered
io scheduler anticipatory registered (default)
atmel_usart.0: ttyS0 at MMIO 0xfefff200 (irq = 1) is a ATMEL_SERIAL
atmel_usart.1: ttyS1 at MMIO 0xfffc4000 (irq = 7) is a ATMEL_SERIAL
brd: module loaded
usbcore: registered new interface driver ub
at91_ether: Your bootloader did not configure a MAC address.
eth0: Link now 100-FullDuplex
eth0: AT91 ethernet at 0xfefbc000 int=24 100-FullDuplex (00:00:00:00:00:00)
eth0: Davicom 9161 PHY (Copper)
Driver 'sd' needs updating - please use bus_type methods
physmap platform flash device: 00200000 at 10000000
physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank
NOR chip too large to fit in mapping. Attempting to cope...
Support for command set 0001 not present
gen_probe: No supported Vendor Command Set found
physmap-flash physmap-flash.0: map_probe failed
at91_cf: irqs det #64, io #0
usbmon: debugfs is not available
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
at91_ohci at91_ohci: AT91 OHCI
at91_ohci at91_ohci: new USB bus registered, assigned bus number 1
at91_ohci at91_ohci: irq 23, io mem 0x00300000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usb usb1: New USB device found, idVendor=1d6b, idProduct=0001
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: AT91 OHCI
usb usb1: Manufacturer: Linux 2.6.28.7 ohci_hcd
usb usb1: SerialNumber: at91
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
udc: at91_udc version 3 May 2006
mice: PS/2 mouse device common for all mice
at91_rtc at91_rtc: rtc core: registered at91_rtc as rtc0
AT91 Real Time Clock driver.
i2c /dev entries driver
i2c-gpio i2c-gpio: using pins 57 (SDA) and 58 (SCL)
AT91 Watchdog Timer enabled (5 seconds, nowayout)
TCP cubic registered
NET: Registered protocol family 17
at91_rtc at91_rtc: setting system clock to 1998-01-01 00:00:26 UTC (883612826)
RAMDISK: Compressed image found at block 0
usb 1-2: new low speed USB device using at91_ohci and address 2
usb 1-2: device descriptor read/64, error -62
VFS: Mounted root (ext2 filesystem).
Freeing init memory: 112K
init started: BusyBox v1.13.3 (2009-04-13 14:04:15 CST)
starting pid 807, tty '': '/etc/init.d/rcS'
ifconfig: SIOCSIFFLAGS: Cannot assign requested address
ifconfig: SIOCSIFFLAGS: Cannot assign requested address
Please press Enter to activate this console. usb 1-2: device descriptor read/64, error -62
usb 1-2: new low speed USB device using at91_ohci and address 3
usb 1-2: device descriptor read/64, error -62
usb 1-2: device descriptor read/64, error -62
usb 1-2: new low speed USB device using at91_ohci and address 4
usb 1-2: device not accepting address 4, error -62
usb 1-2: new low speed USB device using at91_ohci and address 5
usb 1-2: device not accepting address 5, error -62
hub 1-0:1.0: unable to enumerate USB device on port 2
usb 1-1: new full speed USB device using at91_ohci and address 6
usb 1-1: configuration #1 chosen from 1 choice
uba: uba1
usb 1-1: New USB device found, idVendor=0dd8, idProduct=d202
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: USB Flash Disk
usb 1-1: Manufacturer: Netac
usb 1-1: SerialNumber: 03D45B968470384B
starting pid 810, tty '': '-/bin/sh'
# mount -t vfat /dev/sda1 /mnt/usb/
mount: mounting /dev/sda1 on /mnt/usb/ failed: No such device or address
# usb 1-1: USB disconnect, address 6
usb 1-1: new full speed USB device using at91_ohci and address 7
usb 1-1: configuration #1 chosen from 1 choice
uba: uba1
usb 1-1: New USB device found, idVendor=13fe, idProduct=1d00
usb 1-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-1: Product: USB DISK 2.0
usb 1-1: Manufacturer:
usb 1-1: SerialNumber: 077611BE012B
#
# mount -t vfat /dev/sda1 /mnt/usb/
mount: mounting /dev/sda1 on /mnt/usb/ failed: No such device or address
# mount /dev/sda1 /mnt/usb/
mount: mounting /dev/sda1 on /mnt/usb/ failed: No such file or directory
# ls /dev/
console sda sda2 tty1 tty3 zero
null sda1 tty tty2 tty4
# ls /mnt/
usb
# |
|
免费注册
发表于 2009-04-15 11:21
发表于 2009-04-15 13:23
