- 论坛徽章:
- 0
|
RHEL4的服务器上配置了存储设备, 用的Qlogic的HBA card, 能在线识别从存储设备上assign的device, 问题在于, 只要我们重启这台服务器, 存储设备上的device就会变成/dev/sda (原本是/dev/sdc), 导致原来的/dev/sda (系统盘) 变成/dev/sdb, 然后系统根本就启动不了. 麻烦大家赐教.
是否由于先加载了Qlogic的driver, 后加载了SCSI硬盘的? 可是modprobe.conf不是那样的啊.......
===================================================================================================
/etc/modprobe.conf :
alias eth0 bnx2
alias eth1 bnx2
alias scsi_hostadapter aacraid
alias scsi_hostadapter1 ata_piix
alias usb-controller ehci-hcd
alias usb-controller1 uhci-hcd
install qla2xxx /sbin/modprobe qla2xxx_conf; /sbin/modprobe --ignore-install qla2xxx
remove qla2xxx /sbin/modprobe -r --first-time --ignore-remove qla2xxx && { /sbin/modprobe -r --ignore-remove qla2xxx_conf; }
alias qla2100 qla2xxx
alias qla2200 qla2xxx
alias qla2300 qla2xxx
alias qla2322 qla2xxx
alias qla2400 qla2xxx
options qla2xxx ql2xfailover=0 ConfigRequired=0
alias scsi_hostadapter2 qla2xxx_conf
alias scsi_hostadapter3 qla2xxx
alias scsi_hostadapter4 qla2400
===================================================================================================
部分dmesg :
TCP: Hash tables configured (established 262144 bind 43690)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S4 S5)
ACPI wakeup devices:
PCI0
Freeing unused kernel memory: 180k freed
SCSI subsystem initialized
QLogic Fibre Channel HBA Driver
ACPI: PCI interrupt 0000:07:00.0[A] -> GSI 18 (level, low) -> IRQ 217
qla2xxx 0000:07:00.0: Found an ISP2432, irq 217, iobase 0xf8818000
qla2xxx 0000:07:00.0: Configuring PCI space...
PCI: Setting latency timer of device 0000:07:00.0 to 64
qla2xxx 0000:07:00.0: Configure NVRAM parameters...
qla2xxx 0000:07:00.0: Verifying loaded RISC code...
qla2xxx 0000:07:00.0: Allocated (64 KB) for EFT...
qla2xxx 0000:07:00.0: Allocated (1413 KB) for firmware dump...
qla2xxx 0000:07:00.0: Waiting for LIP to complete...
qla2xxx 0000:07:00.0: LIP reset occured (f700).
qla2xxx 0000:07:00.0: LIP occured (f700).
qla2xxx 0000:07:00.0: LIP reset occured (f7f7).
qla2xxx 0000:07:00.0: LOOP UP detected (4 Gbps).
qla2xxx 0000:07:00.0: Topology - (F_Port), Host Loop address 0x0
scsi0 : qla2xxx
qla2xxx 0000:07:00.0:
QLogic Fibre Channel HBA Driver: 8.02.08
QLogic QLE2460 - PCI-Express to 4Gb FC, Single Channel
ISP2432: PCIe (2.5Gb/s x4) @ 0000:07:00.0 hdma+, host#=0, fw=4.03.01 [IP]
Adaptec aacraid driver (1.1-5[2412])
ACPI: PCI interrupt 0000:04:00.0[A] -> GSI 17 (level, low) -> IRQ 209
PCI: Setting latency timer of device 0000:04:00.0 to 64
ServeRAID0: kernel 5.2-0[11835]
ServeRAID0: monitor 5.2-0[11835]
ServeRAID0: bios 5.2-0[11835]
ServeRAID0: serial 40137da
ServeRAID0: 64 Bit DAC enabled
scsi1 : ServeRAID
Vendor: ServeRA Model: 8k-l Mirror Rev: V1.0
Type: Direct-Access ANSI SCSI revision: 02
SCSI device sda: 143132672 512-byte hdwr sectors (73284 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
SCSI device sda: drive cache: write through
SCSI device sda: 143132672 512-byte hdwr sectors (73284 MB)
sda: Write Protect is off
sda: Mode Sense: 03 00 00 00
SCSI device sda: drive cache: write through
=================================================================================================== |
|
免费注册
发表于 2009-03-26 18:31
发表于 2009-03-26 21:22
