- 论坛徽章:
- 0
|
ARM_Linux 启动信息
U-Boot 1.1.4 (May 8 2006 - 15:33:27)
U-Boot code: 33F80000 -> 33F96D4C BSS: -> 33F9B038
RAM Configuration:
Bank #0: 30000000 64 MB
Flash: 16 MB
In: serial
Out: serial
Err: serial
Hit any key to stop autoboot: 0
## Booting image at 32000000 ...
Image Name:
Created: 2006-07-03 9:21:13 UTC
Image Type: ARM Linux Kernel Image (gzip compressed)
Data Size: 796603 Bytes = 777.9 kB
Load Address: 30008000
Entry Point: 30008000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Starting kernel ...
Linux version 2.4.18-rmk7-pxa1 (
shxh@localhost.localdomain
) (gcc version 2.95.3
20010315 (release)) #468 Mon Jul 3 17:20:28 CST 2006
CPU: ARM/CIRRUS Arm920Tsid(wb) revision 0
Machine: Samsung-SMDK2410
Warning: bad configuration page, trying to continue
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: mem=64M console=ttyS0,115200 root=/dev/ram rw initrd=0x3080
0000,6000000 ramdisk_size=15360
Calibrating delay loop... 50.58 BogoMIPS
Memory: 64MB = 64MB total
Memory: 62508KB available (1593K code, 312K data, 56K init)
Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
CPU clock = 202.800000 Mhz, HCLK = 101.400000 Mhz, PCLK = 50.700000 Mhz
Initializing S3C2410 buffer pool for DMA workaround
S3C2410 USB Controller Core Initialized
USB Function Character Driver Interface - 0.5, (C) 2001, Extenex Corp.
usbctl: Opened for usb-char
usbctl: Started for usb-char
Starting kswapd
Journalled Block Device driver loaded
devfs: v1.10 (20020120) Richard Gooch (
rgooch@atnf.csiro.au
)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001 Red Hat, Inc., designed by Axis Communications AB.
8563 init OK
ttyS%d0 at I/O 0x50000000 (irq = 52) is a S3C2410
ttyS%d1 at I/O 0x50004000 (irq = 55) is a S3C2410
ttyS%d2 at I/O 0x50008000 (irq = 58) is a S3C2410
pty: 256 Unix98 ptys configured
s3c2410-ts initialized
S3C2410 Real Time Clock Driver v0.1
Non-volatile memory driver v1.1
block: 128 slots per queue, batch=32
RAMDISK driver initialized: 16 RAM disks of 15360K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
BANKCON2 is 0x700
set ide_CS0 0x10000000 -> ide_base0 0xc4810000, ide_CS1 0x10000010 -> ide_base1
0xc4820010
hda: no response (status = 0xa1), resetting drive
hda: no response (status = 0xa1)
hdb: no response (status = 0xa1), resetting drive
hdb: no response (status = 0xa1)
eth0: cs8900 rev K(3.3 Volts) found at 0xd0000300
cs89x0 media RJ-45, IRQ 37
loop: loaded (max 8 devices)
SCSI subsystem driver Revision: 1.00
request_module[scsi_hostadapter]: Root fs not mounted
begin init_physmap 0x1140000
physmap flash device: 4000000 at 8000000
CFI: Found no Physically mapped flash device at location zero
Search for id:(1006 e594) interleave(1) type(2)
Search for id:(90 e594) i
Search for id:(b004 ffff) interleave(1) type(2)
Search for id:(90 ff) interleave(2) type(1)
Search for id:(90 ff) interleave(2) type(1)
Search for id:(90 ff) interleave(2) type(1)
Search for id:(9090 9090) interleave(2) type(2)
Search for id:(9090 9090) interleave(2) type(2)
Search for id:(9090 9090) interleave(2) type(2)
JEDEC: Found no Physically mapped flash device at location zero
request_module[map_rom]: Root fs not mounted
s3c2410 flash device: 1600000 at 1000000
Search for id:(89 18) interleave(1) type(2)
Search for id:(89 18) interleave(1) type(2)
Search for id:(89 18) interleave(1) type(2)
Search for id:(89 18) interleave(2) type(1)
Search for id:(89 18) interleave(2) type(1)
Search for id:(89 18) interleave(2) type(1)
Search for id:(89 00) interleave(2) type(2)
Search for id:(89 00) interleave(2) type(2)
Search for id:(89 00) interleave(2) type(2)
JEDEC: Found no s3c2410 flash device device at location zero
Using buffer write method
Creating 4 MTD partitions on "s3c2410 flash device":
0x00000000-0x00040000 : "r
0x00040000-0x00140000 : "reserved for kernel"
0x00140000-0x00540000 : "reserved for ramdisk"
0x00800000-0x01000000 : "jffs2(8M)"
smc s3c2410 init start
NAND device: Manufacture ID: 0xec, Chip ID: 0x76 (Samsung K9D1208V0M)
Creating 5 MTD partitions on "Samsung K9D1208V0M":
0x00000000-0x00030000 : "boot"
0x00030000-0x00130000 : "kernel"
0x00130000-0x01530000 : "root"
0x01530000-0x02b30000 : "yaffs part0"
0x02b30000-0x04000000 : "yaffs part1"
smc s3c2410 init ok erasesize = 16384, oobblock = 512, oobsize = 16
mtdblock init start
mtdblock init finish
ftl_cs: FTL header not found.
ftl_cs: FTL header not found.
ftl_cs: FTL header not found.
ftl_cs: FTL header not found.
ftl_cs: FTL header not found.
ftl_cs: FTL header not found.
ftl_cs: FTL header not found.
ftl_cs: FTL header not found.
ftl_cs: FTL header not found.
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xe9000000, IRQ 26
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
port #1 suspened!
port #0 alived!
hub.c: 1 port dete
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 4096)
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
RAMDISK: ext2 filesystem found at block 0
RAMDISK: Loading 4096 blocks [1 disk] into ram disk... done.
Freeing initrd memory: 5859K
EXT2-fs warning: mounting unchecked fs, running e2fsck is recommended
VFS: Mounted root (ext2 filesystem).
Mounted devfs on /dev
Freeing init memory: 56K
==> 1
init started: BusyBox v1.00-pre2 (2004.01.05-08:38+0000) mult?call binary
Bummer, could not run '/etc/init.d/rcS': No such file or directo鷜
Please press Enter to activate this console.
BusyBox v1.00-pre2 (2004.01.05-08:38+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
本文来自ChinaUnix博客,如果查看原文请点:http://blog.chinaunix.net/u2/68147/showart_1120730.html |
|