2.6.14在s3c2410上的移植问题

lengxb

YFLoader# bootm
zImage magic = 0x016f2818
NOW, Booting Linux......
Uncompressing Linux.............................................................
Linux version 2.6.14 (root@bill-desktop) (gcc version 3.4.1) #7 Mon Jul 2 12:147
CPU: ARM920Tid(wb) [41129200] revision 0 (ARMv4T)
Machine: SMDK2410
Warning: bad configuration page, trying to continue
Memory policy: ECC disabled, Data cache writeback
CPU S3C2410A (id 0x32410002)
BUG: mapping for 0x00000000 at 0xc0221760 overlaps vmalloc space
S3C2410: core 200.000 MHz, memory 100.000 MHz, peripheral 50.000 MHz
S3C2410 Clocks, (c) 2004 Simtec Electronics
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
CPU0: D cache: 16384 bytes, associativity 64, 32 byte lines, 8 sets
Built 1 zonelists
Kernel command line: root=/dev/nfs nfsroot=192.168.1.180:/home/a/g15 ip=192.168c
irq: clearing pending ext status 00000100
irq: clearing subpending status 00000003
irq: clearing subpending status 00000002
PID hash table entries: 128 (order: 7, 2048 bytes)
timer tcon=00500000, tcnt a2c1, tcfg 00000200,00000000, usec 00001eb8
Console: colour dummy device 80x30
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 16MB = 16MB total
Memory: 13592KB available (2026K code, 447K data, 100K init)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
softlockup thread 0 started up.
NET: Registered protocol family 16
S3C2410: Initialising architecture
S3C2410 DMA Driver, (c) 2003-2004 Simtec Electronics
DMA channel 0 at c1800000, irq 33
DMA channel 1 at c1800040, irq 34
DMA channel 2 at c1800080, irq 35
DMA channel 3 at c18000c0, irq 36
NetWinder Floating Point Emulator V0.97 (double precision)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS version 1.0, (C) 1999, 2000  Axis Communications AB
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
s3c2410-lcd s3c2410-lcd: no platform data for lcd, cannot attach
s3c2410-lcd: probe of s3c2410-lcd failed with error -22
Console: switching to colour frame buffer device 80x25
fb0: Virtual frame buffer device, using 1024K of video memory
S3C2410 RTC, (c) 2004 Simtec Electronics
s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2410
s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2410
s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2410
io scheduler noop registered
io scheduler cfq registered
RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize
loop: loaded (max 8 devices)
nbd: registered device at major 43
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c2410-nand: mapped registers at c1980000
s3c2410-nand: timing: Tacls 10ns, Twrph0 40ns, Twrph1 10ns
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V 8-bi)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Scanning device for bad blocks
Creating 5 MTD partitions on "NAND 64MiB 3,3V 8-bit":
0x00000000-0x00020000 : "loader"
0x00020000-0x00030000 : "param"
0x00030000-0x001f0000 : "kernel"
0x00200000-0x00400000 : "root"
0x00400000-0x03ef8000 : "user"
mice: PS/2 mouse device common for all mice
ts: Compaq touchscreen protocol output
NET: Registered protocol family 2
IP route cache hash table entries: 256 (order: -2, 1024 bytes)
TCP established hash table entries: 1024 (order: 0, 4096 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
IP-Config: Device `eth0' not found.
Looking up port of RPC 100003/2 on 192.168.1.180
RPC: sendmsg returned error 101
portmap: RPC call returned error 101
Root-NFS: Unable to get nfsd port number from server, using default
Looking up port of RPC 100005/1 on 192.168.1.180
RPC: sendmsg returned error 101
portmap: RPC call returned error 101
Root-NFS: Unable to get mountd port number from server, using default
RPC: sendmsg returned error 101
Root-NFS: Server returned error -101 while mounting /home/a/g15
VFS: Unable to mount root fs via NFS, trying floppy.
VFS: Cannot open root device "nfs" or unknown-block(2,0)
Please append a correct "root=" boot option
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)
几天的文件系统移植还是挂不上去，百度，google了好多文章，也是这个问题，解决方法还没有找到，请高手帮忙，等待并在探索着～～


本文来自ChinaUnix博客，如果查看原文请点：http://blog.chinaunix.net/u/21378/showart_332456.html