- 论坛徽章:
- 0
|
“Linux version 2.4.21-15.EL (bhcompile@bugs.build.redhat.com) (gcc version 3.2.3 20030502 (Red Hat Linux 3.2.3-34)) #1 Thu Apr 22 00:27:41 EDT 2004
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 0000000000100000 - 000000003ffc0000 (usable)
BIOS-e820: 000000003ffc0000 - 000000003ffcfc00 (ACPI data)
BIOS-e820: 000000003ffcfc00 - 000000003ffff000 (reserved)
BIOS-e820: 00000000e0000000 - 00000000f0000000 (reserved)
BIOS-e820: 00000000fec00000 - 00000000fec90000 (reserved)
BIOS-e820: 00000000fed00000 - 00000000fed00400 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee10000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
127MB HIGHMEM available.
896MB LOWMEM available.
On node 0 totalpages: 262080
zone(0): 4096 pages.
zone(1): 225280 pages.
zone(2): 32704 pages.
Kernel command line: ro root=LABEL=/
Initializing CPU#0
Detected 3000.234 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 5989.99 BogoMIPS
Memory: 1026784k/1048320k available (1528k kernel code, 17956k reserved, 1065k data, 164k init, 130816k highmem)
zapping low mappings.
Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
Inode cache hash table entries: 65536 (order: 7, 524288 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer cache hash table entries: 65536 (order: 6, 262144 bytes)
Page-cache hash table entries: 262144 (order: 8, 1048576 bytes)
CPU: Trace cache: 12K uops<6>Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: After generic, caps: bfebfbff 20100000 00000000 00000000
CPU: Common caps: bfebfbff 20100000 00000000 00000000
CPU: Intel(R) Xeon(TM) CPU 3.00GHz stepping 0a
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
Process timing init...done.
mtrr: v1.40 (20010327) Richard Gooch (rgooch@atnf.csiro.au)
mtrr: detected mtrr type: Intel
PCI: PCI BIOS revision 2.10 entry at 0xfc3de, last bus=4
PCI: Using configuration type 1
PCI: Probing PCI hardware
PCI: Ignoring BAR0-3 of IDE controller 00:1f.1
Transparent bridge - Intel Corp. 82801BA/CA/DB/EB PCI Bridge
PCI: Using IRQ router PIIX [8086/24d0] at 00:1f.0
PCI: Found IRQ 11 for device 00:02.0
PCI: Sharing IRQ 11 with 00:1d.0
PCI: Sharing IRQ 11 with 02:04.0
PCI: Found IRQ 5 for device 00:1f.1
PCI: Sharing IRQ 5 with 00:1f.2
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
apm: BIOS not found.
Total HugeTLB memory allocated, 0
Starting kswapd
allocated 32 pages and 32 bhs reserved for the highmem bounces
VFS: Disk quotas vdquot_6.5.1
aio_setup: num_physpages = 65520
aio_setup: sizeof(struct page) = 56
Hugetlbfs mounted.
pty: 2048 Unix98 ptys configured
Serial driver version 5.05c (2001-07-0 with MANY_PORTS MULTIPORT SHARE_IRQ SERIAL_PCI ISAPNP enabled
ttyS0 at 0x03f8 (irq = 4) is a 16550A
Real Time Clock Driver v1.10e
NET4: Frame Diverter 0.46
RAMDISK driver initialized: 256 RAM disks of 8192K size 1024 blocksize
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ICH5: IDE controller at PCI slot 00:1f.1
PCI: Enabling device 00:1f.1 (0005 -> 0007)
PCI: Found IRQ 5 for device 00:1f.1
PCI: Sharing IRQ 5 with 00:1f.2
ICH5: chipset revision 2
ICH5: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda MA, hdb:pio
hda: TEAC CD-ROM CD-224E-N, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide-floppy driver 0.99.newide
ide-floppy driver 0.99.newide
md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: Autodetecting RAID arrays.
md: autorun ...
md: ... autorun DONE.
Initializing Cryptographic API
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 8192 buckets, 64Kbytes
TCP: Hash tables configured (established 262144 bind 65536)
Linux IP multicast router 0.06 plus PIM-SM
Initializing IPsec netlink socket
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 243k freed
VFS: Mounted root (ext2 filesystem).
SCSI subsystem driver Revision: 1.00
libata version 1.01 loaded.
ata_piix version 1.00
PCI: Found IRQ 5 for device 00:1f.2
PCI: Sharing IRQ 5 with 00:1f.1
PCI: Setting latency timer of device 00:1f.2 to 64
ata1: SATA max UDMA/133 cmd 0xCCB8 ctl 0xCCB2 bmdma 0xCC80 irq 5
ata2: SATA max UDMA/133 cmd 0xCCA0 ctl 0xCC9A bmdma 0xCC88 irq 5
ata1: dev 0 cfg 49:2f00 82:346b 83:7701 84:4023 85:3469 86:3401 87:4023 88:207f
ata1: dev 0 ATA, max UDMA/133, 156250000 sectors (lba4
ata1: dev 0 configured for UDMA/133
ata2: SATA port disabled. ignoring.
ata2: thread exiting
scsi0 : ata_piix
scsi1 : ata_piix
Vendor: ATA Model: ST3808110AS Rev: 1.01
Type: Direct-Access ANSI SCSI revision: 05
Attached scsi disk sda at scsi0, channel 0, id 0, lun 0
SCSI device sda: 156250000 512-byte hdwr sectors (80000 MB)
Partition check:
sda: sda1 sda2 sda3 sda4 < sda5 >
Journalled Block Device driver loaded
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: sd(8,2): orphan cleanup on readonly fs
ext3_orphan_cleanup: deleting unreferenced inode 229678
ext3_orphan_cleanup: deleting unreferenced inode 229677
ext3_orphan_cleanup: deleting unreferenced inode 229676
ext3_orphan_cleanup: deleting unreferenced inode 229674
EXT3-fs: sd(8,2): 4 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 164k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-uhci.c: $Revision: 1.275 $ time 00:34:03 Apr 22 2004
usb-uhci.c: High bandwidth mode enabled
PCI: Found IRQ 11 for device 00:1d.0
PCI: Sharing IRQ 11 with 00:02.0
PCI: Sharing IRQ 11 with 02:04.0
PCI: Setting latency timer of device 00:1d.0 to 64
usb-uhci.c: USB UHCI at I/O 0xcce0, IRQ 11
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
PCI: Found IRQ 10 for device 00:1d.1
PCI: Setting latency timer of device 00:1d.1 to 64
usb-uhci.c: USB UHCI at I/O 0xccc0, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
PCI: Found IRQ 6 for device 00:1d.7
PCI: Setting latency timer of device 00:1d.7 to 64
ehci-hcd 00:1d.7: Intel Corp. 82801EB USB2
ehci-hcd 00:1d.7: irq 6, pci mem f8892000
usb.c: new USB bus registered, assigned bus number 3
ehci-hcd 00:1d.7: enabled 64bit PCI DMA
PCI: 00:1d.7 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 00:1d.7 PCI cache line size corrected to 128.
ehci-hcd 00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2003-Jan-22
hub.c: USB hub found
hub.c: 4 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <vojtech@suse.cz>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,2), internal journal
Adding Swap: 2096472k swap-space (priority -1)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,1), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on sd(8,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
IA-32 Microcode Update Driver: v1.13 <tigran@veritas.com>
microcode: No suitable data for cpu 0
inserting floppy driver for 2.4.21-15.EL
floppy0: Unable to grab IRQ6 for the floppy driver
Intel(R) PRO/1000 Network Driver - version 5.2.30.1-k1
Copyright (c) 1999-2004 Intel Corporation.
PCI: Found IRQ 11 for device 02:04.0
PCI: Sharing IRQ 11 with 00:02.0
PCI: Sharing IRQ 11 with 00:1d.0
divert: allocating divert_blk for eth0
eth0: Intel(R) PRO/1000 Network Connection
PCI: Found IRQ 3 for device 04:03.0
divert: allocating divert_blk for eth1
eth1: Intel(R) PRO/1000 Network Connection
divert: freeing divert_blk for eth0
divert: freeing divert_blk for eth1
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
Intel(R) PRO/1000 Network Driver - version 5.2.30.1-k1
Copyright (c) 1999-2004 Intel Corporation.
PCI: Found IRQ 11 for device 02:04.0
PCI: Sharing IRQ 11 with 00:02.0
PCI: Sharing IRQ 11 with 00:1d.0
divert: allocating divert_blk for eth0
eth0: Intel(R) PRO/1000 Network Connection
PCI: Found IRQ 3 for device 04:03.0
divert: allocating divert_blk for eth1
eth1: Intel(R) PRO/1000 Network Connection
e1000: eth0 NIC Link is Up 100 Mbps Full Duplex
ip_tables: (C) 2000-2002 Netfilter core team
ip_tables: (C) 2000-2002 Netfilter core team
audit subsystem ver 0.1 initialized
Audit daemon registered (process 3194)
lp: driver loaded but no devices found
MNMD:0xf8a72f00:<eth0>:0x3cb3afde,mac<00:15:C5:5D:ED:13>
MNMD:0xf8a72f00:<eth1>:0x8b2702dd,mac<00:15:C5:5D:ED:14>
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 941M
agpgart: no supported devices found.
[drm] Initialized radeon 1.7.0 20020828 on minor 0
PCI: Found IRQ 11 for device 04:0d.0”
很长一段辛苦各位大侠了。 |
|
免费注册
发表于 2007-06-03 17:11
