我的sled10(64)+adsl上不了网！狂晕！给我看看

泳涟涟

我用的是sled10(64)+adsl拔号上网！！设dsl后再ifup dsl0不行！！能改的网络设置我都改了！！就是不行！我又安了rp-pppoe也没联上！但是有一个提示，在配置里好像找不到modem（我用的是大亚科技的DB108-G）会不会是sled10不支持这个modem！！（我先后装上了ubuntu,magic都能上网）有没有的治啊！我用了这个sled半年了不想换啊下面是配置rp-pppoe时的内容请大哥给我看看，指点小弟一下！！先谢了

yong:~ # pppoe-setup
Welcome to the Roaring Penguin PPPoE client setup.  First, I will run
some checks on your system to make sure the PPPoE client is installed
properly...
Looks good!  Now, please enter some information:
USER NAME
>>> Enter your PPPoE user name (default bxxxnxnx@sympatico.ca): wh10020438
INTERFACE
>>> Enter the Ethernet interface connected to the DSL modem
For Solaris, this is likely to be something like /dev/hme0.
For Linux, it will be ethn, where 'n' is a number.
(default eth0):
MODEM TYPE
We will try to detect if your modem is compliant with RFC 2516
or not. 3COM's 3CP4130 is *NOT* compliant, for instance.
Searching for a modem at interface eth0...
Not found, trying with 3COM's code...
Didn't find a modem at interface eth0, you can continue but
things might not work as you expect...
You might want to re-run this script and try a different interface.
Do you want the link to come up on demand, or stay up continuously?
If you want it to come up on demand, enter the idle time in seconds
after which the link should be dropped.  If you want the link to
stay up permanently, enter 'no' (two letters, lower-case.)
NOTE: Demand-activated links do not interact well with dynamic IP
addresses.  You may have some problems with demand-activated links.
>>> Enter the demand value (default no):
DNS
Please enter the IP address of your ISP's primary DNS server.
If your ISP claims that 'the server will provide DNS addresses',
enter 'server' (all lower-case) here.
If you just press enter, I will assume you know what you are
doing and not modify your DNS setup.
>>> Enter the DNS information here: server
PASSWORD
>>> Please enter your PPPoE password:
>>> Please re-enter your PPPoE password:
FIREWALLING
Please choose the firewall rules to use.  Note that these rules are
very basic.  You are strongly encouraged to use a more sophisticated
firewall setup; however, these will provide basic security.  If you
are running any servers on your machine, you must choose 'NONE' and
set up firewalling yourself.  Otherwise, the firewall rules will deny
access to all standard servers like Web, e-mail, ftp, etc.  If you
are using SSH, the rules will block outgoing SSH connections which
allocate a privileged source port.
The firewall choices are:
0 - NONE: This script will not set any firewall rules.  You are responsible
          for ensuring the security of your machine.  You are STRONGLY
          recommended to use some kind of firewall rules.
1 - STANDALONE: Appropriate for a basic stand-alone web-surfing workstation
2 - MASQUERADE: Appropriate for a machine acting as an Internet gateway
                for a LAN
>>> Choose a type of firewall (0-2): 0
** Summary of what you entered **
Ethernet Interface: eth0
User name:          wh10020438
Activate-on-demand: No
DNS addresses:      Supplied by ISP's server
Firewalling:        NONE
>>> Accept these settings and adjust configuration files (y/n)? y
Adjusting /etc/ppp/pppoe.conf
Adjusting /etc/ppp/pap-secrets and /etc/ppp/chap-secrets
  (But first backing it up to /etc/ppp/pap-secrets-bak)
  (But first backing it up to /etc/ppp/chap-secrets-bak)

Congratulations, it should be all set up!
Type 'pppoe-start' to bring up your PPPoE link and 'pppoe-stop' to bring
it down.  Type 'pppoe-status' to see the link status.
yong:~ # pppoe-start
................TIMED OUT

泳涟涟

小弟解决了！！！！！！！