发个求救贴-------路由器不能Ping通S口

草末儿茶

两台路由器通过帧中继专线连接64k
但都Ping不通自己的S口，也ping不通对方，请各位GG,JJ指点一下。
路由器Cisco2610 E0/0地址：192.168.2.23
                S0/0地址：10.10.2.23


----------sh int--------------
Ethernet0/0 is up, line protocol is up
  Hardware is AmdP2, address is 0005.bddc.112a (bia 0005.bddc.112a)
  Internet address is 192.168.2.23/24
  MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output 00:00:00, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue :0/40 (size/max)
  5 minute input rate 1000 bits/sec, 1 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     4309 packets input, 594094 bytes, 0 no buffer
     Received 848 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored
     0 input packets with dribble condition detected
     2453 packets output, 225767 bytes, 0 underruns
     0 output errors, 0 collisions, 3 interface resets
     0 babbles, 0 late collision, 0 deferred
     0 lost carrier, 0 no carrier
--More--
  Hardware is PowerQUICC Serial
  Description: to the cisco22
  Internet address is 10.10.2.23/26
  MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation FRAME-RELAY IETF, loopback not set
  Keepalive set (10 sec)
  LMI enq sent  341, LMI stat recvd 305, LMI upd recvd 0, DTE LMI up
  LMI enq recvd 25, LMI stat sent  0, LMI upd sent  0
  LMI DLCI 0  LMI type is ANSI Annex D  frame relay DTE
  Broadcast queue 0/64, broadcasts sent/dropped 0/0, interface broadcasts 0
  Last input 00:00:04, output 00:00:04, output hang never
  Last clearing of "show interface" counters 00:56:54
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue :0/40 (size/max)
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     331 packets input, 4890 bytes, 0 no buffer
     Received 0 broadcasts, 0 runts, 0 giants, 0 throttles
     7 input errors, 0 CRC, 7 frame, 0 overrun, 0 ignored, 0 abort
     341 packets output, 4763 bytes, 0 underruns

--------------sh run------------
Current configuration : 840 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname 00123
!
enable secret 5 $1$8ESf$JQtM1wGM67BYIBpXcbKwS0
enable password quickcar
!
ip subnet-zero
!
!
!
!
!
!
interface Ethernet0/0
ip address 192.168.2.23 255.255.255.0
ip nat inside
--More--
no ip mroute-cache
full-duplex
!
interface Serial0/0
description to the cisco22
ip address 10.10.2.23 255.255.255.192
ip nat outside
encapsulation frame-relay IETF
no ip mroute-cache
no fair-queue
frame-relay map ip 10.10.1.22 16
frame-relay interface-dlci 16
frame-relay lmi-type ansi
!
ip classless
ip route 0.0.0.0 0.0.0.0 10.10.1.22
ip route 192.168.1.0 255.255.255.0 10.10.1.22
ip http server
ip pim bidir-enable
!
!
snmp-server community public RO
!
--More--               
line con 0
line aux 0
line vty 0 4
password cisco23
login
!
!
end         

----------sh frame-relay lmi---------
LMI Statistics for interface Serial0/0 (Frame Relay DTE) LMI TYPE = ANSI
  Invalid Unnumbered info 0                Invalid Prot Disc 0
  Invalid dummy Call Ref 0                Invalid Msg Type 0
  Invalid Status Message 0                Invalid Lock Shift 0
  Invalid Information ID 0                Invalid Report IE Len 0
  Invalid Report Request 0                Invalid Keep IE Len 0
  Num Status Enq. Sent 354                Num Status msgs Rcvd 318
  Num Update Status Rcvd 0                Num Status Timeouts 36
-----------------sh frame-relay pvc----------
00123#sh frame-relay pvc

PVC Statistics for interface Serial0/0 (Frame Relay DTE)

              Active     Inactive      Deleted       Static
  Local          1            0            0            0
  Switched       0            0            0            0
  Unused         0            0            0            0

DLCI = 16, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0/0

  input pkts 0             output pkts 0            in bytes 0
  out bytes 0              dropped pkts 0           in FECN pkts 0
  in BECN pkts 0           out FECN pkts 0          out BECN pkts 0
  in DE pkts 0             out DE pkts 0
  out bcast pkts 0         out bcast bytes 0
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
  pvc create time 00:59:43, last time pvc status changed 00:13:33           


Cisco 2610     E0地址：192.168.1.22
               S0地址：10.10.1.22
-------sh run---------
Current configuration : 797 bytes
!
version 12.2
service timestamps debug uptime
service timestamps log uptime
no service password-encryption
!
hostname 00022A
!
enable secret 5 $1$Qsxy$rkFOP36q.8DTr7IWKvCeZ.
enable password quickcar
!
ip subnet-zero
!
!
!
!
!
!
interface Ethernet0/0
ip address 192.168.1.22 255.255.255.0
no ip mroute-cache
full-duplex
--More--
!
interface Serial0/0
description to cisco23
ip address 10.10.1.22 255.255.255.192
encapsulation frame-relay
no ip mroute-cache
frame-relay map ip 10.10.10.23 16 broadcast
frame-relay interface-dlci 16
frame-relay lmi-type ansi
!
ip classless
ip route 0.0.0.0 0.0.0.0 10.10.2.23
ip route 192.168.2.0 255.255.255.0 10.10.2.23
ip http server
ip pim bidir-enable
!
!
snmp-server community public RO
!
line con 0
line aux 0
line vty 0 4
password cisco22
--More--
----------------sh frame-relay pvc-------
00022A#sh frame-relay pvc

PVC Statistics for interface Serial0/0 (Frame Relay DTE)

              Active     Inactive      Deleted       Static
  Local          1            0            0            0
  Switched       0            0            0            0
  Unused         0            0            0            0

DLCI = 16, DLCI USAGE = LOCAL, PVC STATUS = ACTIVE, INTERFACE = Serial0/0

  input pkts 0             output pkts 0            in bytes 0
  out bytes 0              dropped pkts 0           in FECN pkts 0
  in BECN pkts 0           out FECN pkts 0          out BECN pkts 0
  in DE pkts 0             out DE pkts 0
  out bcast pkts 0         out bcast bytes 0
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
  pvc create time 23:23:30, last time pvc status changed 00:18:16  

----------------sh frame-relay lmi-----------
00022A#sh frame-relay lmi

LMI Statistics for interface Serial0/0 (Frame Relay DTE) LMI TYPE = ANSI
  Invalid Unnumbered info 0                Invalid Prot Disc 0
  Invalid dummy Call Ref 0                Invalid Msg Type 0
  Invalid Status Message 0                Invalid Lock Shift 0
  Invalid Information ID 0                Invalid Report IE Len 0
  Invalid Report Request 0                Invalid Keep IE Len 0
  Num Status Enq. Sent 8381                Num Status msgs Rcvd 8357
  Num Update Status Rcvd 0                Num Status Timeouts 25

------------------sh int-----------
Ethernet0/0 is up, line protocol is up
  Hardware is AmdP2, address is 0005.bddc.1152 (bia 0005.bddc.1152)
  Internet address is 192.168.1.22/24
  MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation ARPA, loopback not set
  Keepalive set (10 sec)
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:00, output 00:00:00, output hang never
  Last clearing of "show interface" counters never
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: fifo
  Output queue :0/40 (size/max)
  5 minute input rate 4000 bits/sec, 1 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     134240 packets input, 43191544 bytes, 0 no buffer
     Received 124276 broadcasts, 0 runts, 0 giants, 0 throttles
     1 input errors, 1 CRC, 0 frame, 0 overrun, 0 ignored
     0 input packets with dribble condition detected
     16047 packets output, 1502952 bytes, 0 underruns
     14 output errors, 0 collisions, 4 interface resets
     0 babbles, 0 late collision, 4 deferred
     14 lost carrier, 0 no carrier
--More--
Serial0/0 is up, line protocol is up
  Hardware is PowerQUICC Serial
  Description: to cisco23
  Internet address is 10.10.1.22/26
  MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation FRAME-RELAY, loopback not set
  Keepalive set (10 sec)
  LMI enq sent  8386, LMI stat recvd 8362, LMI upd recvd 0, DTE LMI up
  LMI enq recvd 0, LMI stat sent  0, LMI upd sent  0
  LMI DLCI 0  LMI type is ANSI Annex D  frame relay DTE
  Broadcast queue 0/64, broadcasts sent/dropped 1/0, interface broadcasts 12
  Last input 00:00:01, output 00:00:01, output hang never
  Last clearing of "show interface" counters 23:25:05
  Input queue: 0/75/0/0 (size/max/drops/flushes); Total output drops: 0
  Queueing strategy: weighted fair
  Output queue: 0/1000/64/0 (size/max total/threshold/drops)
     Conversations  0/1/256 (active/max active/max total)
     Reserved Conversations 0/0 (allocated/max allocated)
     Available Bandwidth 1158 kilobits/sec
  5 minute input rate 0 bits/sec, 0 packets/sec
  5 minute output rate 0 bits/sec, 0 packets/sec
     8369 packets input, 124153 bytes, 0 no buffer
--More--


        

草末儿茶

自已顶一下。     

hnpygqs

ip routeing

野百合

小草末，是不是贴错地方了？

linziwei

12.2IOS不需要LMI指定，去掉试试

在点对点上的第三层地址和DLCI之间不需要映射

或在S0口指定子接口，打上POINT -TO - POINT


GOOD LUCK！

草末儿茶

原帖由 "linziwei" 发表：


或在S0口指定子接口，打上POINT -TO - POINT


GOOD LUCK！

如何打，请教我。     

草末儿茶

[quote]原帖由 "野百合"]小草末，是不是贴错地方了？[/quote 发表：



我是觉得这里人气旺才贴在这里。
百合老大，就原谅。       

草末儿茶

[quote]原帖由 "hnpygqs"]ip routeing[/quote 发表：


已经做过了。     

safe

把对端的ROUTER配置也贴出来,看看

yahnet

int s0
no ip address
encapsulation frame-relay

int s0.1 point-to-point
把上面在S0上的配置全抄到这里

另LINE是UP,但没数据包流过.按理说LMI状态查询也是有数据流过
可以debug frame-relay lmi
和show frame-relay map 确认是否作了映射