- 论坛徽章:
- 0
|
***** EARLY BOOT VFP : SYSTEM ALERT *****
SYSTEM NAME: uninitialized
DATE: 01/02/1970 TIME: 07:35:49
ALERT LEVEL: 6 = Boot possible, pending failure - action required
REASON FOR ALERT
SOURCE: 8 = I/O
SOURCE DETAIL: 9 = serial SOURCE ID: 0
PROBLEM DETAIL: 3 = functional failure
LEDs: RUN ATTENTION FAULT REMOTE POWER
FLASH FLASH FLASH ON ON
LED State: Unexpected Reboot. Running non-OS code. Non-critical error detected.
Check Chassis and Console Logs for error messages.
0x00000063890014C0 00000000 00000000 - type 0 = Data Field Unused
0x58000863890014C0 00004600 02072331 - type 11 = Timestamp 01/02/1970 07:35:49
A/a: ack read of this entry - Q/q: quit Virtual Front Panel Display
Anything else redisplay the log entry
->Choice:a
*****************************************
*****************************************
************ EARLY BOOT VFP *************
End of early boot detected
*****************************************
10 seconds expired.
Proceeding...
Trying Primary Boot Path
------------------------
Booting...
Boot IO Dependent Code (IODC) revision 1
HARD Booted.
ISL Revision A.00.43 Apr 12, 2000
ISL booting hpux
Boot
: disk(0/0/1/1.2.0.0.0.0.0;0)/stand/vmunix
9621504 + 1720320 + 19580728 start 0x1edc68
alloc_pdc_pages: Relocating PDC from 0xffff800000 to 0x7fa01000.
************* SYSTEM ALERT **************
SYSTEM NAME: uninitialized
DATE: 01/02/1970 TIME: 07:37:48
ALERT LEVEL: 7 = reserved
REASON FOR ALERT
SOURCE: 0 = unknown, no source stated
SOURCE DETAIL: 0 = unknown, no source stated SOURCE ID: FF
PROBLEM DETAIL: 0 = no problem detail
LEDs: RUN ATTENTION FAULT REMOTE POWER
FLASH FLASH FLASH ON ON
LED State: Unexpected Reboot. Running non-OS code. Non-critical error detected.
Check Chassis and Console Logs for error messages.
0x0000207000FF6292 00000000 7FA01000 - type 0 = Data Field Unused
0x5800287000FF6292 00004600 02072530 - type 11 = Timestamp 01/02/1970 07:37:48
A: ack read of this entry - X: Disable all future alert messages
Anything else skip redisplay the log entry
->Choice
*****************************************
CAUTION: System Alerts have been disabled. This will re-enable with
a re-boot or power-on of the system. To re-enable system alerts now, you
may use the AC (Alert Display Configuration) command.
************* SYSTEM ALERT **************
Alert messages are now disabled. Enter Commands Interface AC command
to enable them again
*****************************************
Console reset done.
Boot device reset done.
******* Unexpected HPMC. Processor HPA FFFFFFFF'FED61000 *******
GENERAL REGISTERS:
r00/03 00000000'00000000 00000000'00000001 00000000'001F4764 00000000'022893C8
r04/07 00000000'00AE7800 FFFFFF00'FFFFFFFF 00000000'009FCEA0 00000000'00AE7800
r08/11 80000000'00000000 FFFFFFFF'FFFFFFFF 00000000'000000F6 00000000'000000FE
r12/15 00000000'000000F2 00000000'00000002 00000000'000000F0 00000000'000000FF
r16/19 000000FF'FF800FF8 FFFFFFFF'FF40E000 00000000'00000000 00000000'00000001
r20/23 00000000'00000000 00000000'00000002 00000000'00000780 00000000'00000002
r24/27 00000000'00000000 FFFFFFFF'FED21000 00000000'00000000 00000000'00AF1000
r28/31 FFFFFFFF'FFFFFFFF 00000000'0228E0E0 00000000'0228E110 00000000'00000000
CONTROL REGISTERS:
sr0/3 00000000'00000000 00000000'00000000 00000000'00000000 00000000'00000000
sr4/7 00000000'00000000 00000000'00000000 00000000'0C4A3400 00000000'00000000
pcq = 00000000'00000000.00000000'0016A0E0 00000000'00000000.00000000'0016A0E4
isr = 00000000'14340008 ior = 00000000'A3A8E100 iir = 239FFFFF rctr = 00000000
pid reg cr8/cr9 00000000'00000000 00000000'00000000
pid reg cr12/cr13 00000000'00000000 00000000'00000000
ipsw = 000000FF'0800FF09 iva = 00000000'0002A000 sar = 03 ccr = C0
tr0/3 00000000'022893C8 00000000'04000000 00000000'00041020 000000FF'FF95C820
tr4/7 55555555'55555555 55555555'55555555 000000FF'FF40C8A8 00000000'00008020
eiem = 04000000'00000000 eirr = 00000000'00000000 itmr = 00000027'5C70653D
cr1/4 00000000'00000000 00000000'00000000 00000000'00000000 00000000'00000000
cr5/7 00000000'00000000 00000000'00000000 00000000'00000000
MACHINE CHECK PARAMETERS:
Check Type = 20000000 CPU STATE = 9E000004 Cache Check = 00000000
TLB Check = 00000000 Bus Check = 0030000D PIM State = ? SIU Status = ????????
Assists = 00000000 Processor = 00000000
Slave Addr = FFFFFFFF'FED61000 Master Addr = 000000FF'FED60000
HPMC, pcsq.pcoq = 0'0.0'16a0e0 , isr.ior = 0'14340008.0'a3a8e100
@(#) $Revision: vmunix: vw: -proj selectors: CUPI80_BL2000_1108 -c 'Vw fo
r CUPI80_BL2000_1108 build' -- cupi80_bl2000_1108 'CUPI80_BL2000_1108' Wed Nov
8 19:24:56 PST 2000 $High-priority machine check: (display==0xd910, flags==0x0)
Processor 1 TOC: pcsq.pcoq = 0'0.0'3c58a0
isr.ior = 0'a627fe7f.c0000000'fd3c5048
* CPU State 0x9e000004
* Bus Check 0x30000d
* Slave Address 0xffffffff'0xfed61000
* Master Address 0xff'0xfed60000
*** A system crash has occurred. (See the above messages for details.)
*** The system is now preparing to dump physical memory to disk, for use
*** in debugging the crash.
ERROR: Your system crashed before I/O and dump configuration was complete.
A crash dump cannot be taken under these circumstances without
special configuration. Contact your HP support representative. |
|