- 论坛徽章:
- 2
|
本帖最后由 东方蜘蛛 于 2011-06-14 10:29 编辑
本文由我参考官方文档整理而出,如需转帖请注明出处。
环境/产品
1.硬件:Sun SPARC Enterprise T5240(FW: 7.2.9.b;OBP: 4.30.8.a;ILOM: 3.0.10.2.b)
2.软件:Solaris 10,SVM
现象描述
默认用户和密码无法登录SP(root/changeme)
解决方法一(适用于ILOM版本在3.0以上的T系列主机)
1.使用串口线连接至Serial Mgmt Port(至少一个电源接电,OS起停均可);
2.在ILOM登录提示符下输入default用户名及其默认密码:
wb87proxy15-ILOM login: default
Press and release the physical presence button.
Press return when this is completed...
重点:这里说的button不是电源按钮,而是Locator button,在主机后面
。这时,白色的Locator LED会开始闪烁,再按回车,输入default用户的默认密码。
Password: defaultpassword
Waiting for daemons to initialize...
Daemons ready
Oracle(R) Integrated Lights Out Manager
Version 3.0.10.2.b r56134
Copyright (c) 2010, Oracle and/or its affiliates. All rights reserved.
Warning: The system appears to be in manufacturing test mode.
Contact Service immediately.
->
3.重新设置root用户密码:
-> set /SP/users/root password
Enter new password: changeme
Enter new password again: changeme
-> exit
wb87proxy15-ILOM login: root
Password: changeme
Waiting for daemons to initialize...
Daemons ready
Oracle(R) Integrated Lights Out Manager
Version 3.0.10.2.b r56134
Copyright (c) 2010, Oracle and/or its affiliates. All rights reserved.
Warning: The system appears to be in manufacturing test mode.
Contact Service immediately.
Warning: password is set to factory default.
->
解决方法二(由Oracle内部提供,但未经验证)
1.需要提前准备一个跳线冒;
2.关闭主机系统并poweroff硬件,断开电源线;
3.做好ESD的注意事项;
4.打开上面板,拆下右边二个PCIe/XAUI 竖隔板部件(后视角度);
5.将跳线冒插入主板J10401跳线的pins 1&2,顺序从上到下依次为:1,2,3,如下图:
6.插回右边二个PCIe/XAUI 竖隔板部件,盖好上面板;
7.接好电源,按下前面板的电源按钮开机;
8.这时,SP层由于做了掉线,会将SP的root密码强制设置为changeme;
9.使用root/changeme登录SP,修改root密码为mechange;
10.关闭主机系统并poweroff硬件,断开电源线;
11.做好ESD的注意事项;
12.打开上面板,拆下右边二个PCIe/XAUI 竖隔板部件(后视角度);
13.拆掉J10401上的跳线冒;
14.插回右边二个PCIe/XAUI 竖隔板部件,盖好上面板;
15.接好电源,连接串口到Serial Mgmt Port;
16.使用root/mechange登录SP,如果需要修改为其他密码,则使用set命令修改即可。
建议与总结
1.方法一简单适用,应该适用于所有T系列主机,但目前只验证了T5140/T5240(主板通用),且有个前提是ILOM要在3.0以上版本。
2.方法二虽然出自Oracle内部,但具有一定风险,能用方法一解决的,尽量别适用方法二。 |
评分
-
查看全部评分
|