求网卡的安装方法！

破口

我的网卡是Realtek，请指点一下网卡的安装方法

blxiao

用netconfig

scpxlijun

搜索旧贴,有N多.

unixgaoshou

以root用户登陆系统
1、查看A盘内容（将网卡驱动拷到A盘）：
dosdir a:/
2、拷贝网卡的驱动程序到任意目录（如/tmp）
doscp a:/****.IMG /tmp
3、改驱动程序的名字为：VOL.000.000
  cd /tmp
  cp  ****.IMG  VOL.000.000
4、运行custom安装软件（目录指定到/tmp)
5、运行"netconfig" 进行网络配置
6、重新启动系统(reboot)

sdccf

一篇安装网卡的文章：

http://unix-cd.huaanpawn.com/bbs/ShowPost.asp?id=84

haojing1977

二楼的太详细了，同意

笨@笨

新手应该像我一样,
多用用搜索功能,

hsgzr

用custom

pcyt

SCO UNIX 5.X

   Introduction:
   -------------
      This document describes the procedure to install the SCO UNIX driver
      for REALTEK RTL8139 PCI ethernet adapter.

   Location of Driver:     \SCO\5.X\8139.VOL

   Installing driver procedure on SCO UNIX :
   -----------------------------------------
      Before you start with the installation  process,  make sure that the
      SCO UNIX system is properly installed. Similarly,your adapter should
      also be properly installed in your machine.

     1. Installation Diskette in DOS format.
        Put RTL SCO UNIX Driver diskette to floppy A: and use doscp
        command to copy RTL SCO UNIX PCI Driver into UNIX's directories.

       # cd /
       # doscp A:setup  /setup
       # chmod +x /setup
       # ./setup


         Then, the install program will ask you for path of the files,
         you can key in:

                      a:/sco/5.x
               or
                      b:/sco/5.x
     2.  Run 'custom' utility to add RTL8139 driver software to system.

          Select the following option::
                "Software"
                  ->; "Install New"
                ->; "From 'your computer'"
                  ->; 'MediaImages"
         Then enter the directory of driver image(8139.VOL) which
         should be "/tmp"

     3.    Use netconfig utility

          Avaiable options:

          # netconfig

     4.  To add adapters, select "Add New Lan Adapter" from "Hardware".

     5.  Select the line speed from the menu:

            (1)Hwset,(2)Auto,(3)10half.(4)10full.(5)100half.(6)100full.

         if you select Hwset, driver will read configuration from EEPROM
         on the card. the configuration can be modified by running
         'rset8139' in the driver disk. The program is for DOS.

     6.  Add Protocol to select SCO TCP/IP.

     7.  Enter the internet Address of this interface,
         for example : 192.9.9.1

     8.  Enter the netmask for this interface
           (default 255.255.255.0)

     9.  Enter the boardcast address for this interface
          use default: n.n.n.n

    10.  Do you want to relink to kernel now ? (y/n)
          type in 'y'


    11. Do you want this kernel to boot by default (y/n)
          type in 'y'


    11. Do you want the kernel environment rebuilt (y/n)
          type in 'y'

    12. Reboot unix

            # shutdown -y -g0
这是我一个8139网卡的安装说明,看看行不?

saintdragon

openserver还是unixware？
openserver一般将文件cp到硬盘后，改名为VOL.000.000，然后用custom安装驱动程序。然后用netconfig命令配置。
unixware系统，一般用pkgadd安装驱动。然后用netcfg命令配置。