- 论坛徽章:
- 0
|
本帖最后由 幽冥公子 于 2011-10-14 12:09 编辑
小弟愚钝,看不明白具体报错在那里,请高手帮忙看下,谢谢。
Severity: Warning -- not failed but attention recommended or required. A Fibre Channel port on the HSV200 controller has failed to respond.
Error reading extended event description from c:\hsvmafiles\napp\eventout.txt
EIP08 - Fibre Channel Services Fibre Channel Port Link Failure
A Fibre Channel port link has failed or a Drive Enclosure Environmental Monitoring Unit task has failed.
Event Log Packet Event Specific Information
flags (Flags)
Flag field bits: 00000011
Time has been set on this HSV200 controller: TRUE
Time has been synchronized with all HSV200 controllers in the Storage System: TRUE
Event sequence number reset occurred: FALSE
Event reported out of sequence due to Final Event Block reconciliation or lost host event: FALSE
Event requeued following restart or resynchronization: FALSE
Event reported using LAB code: FALSE
Event reported by primary HSV200 controller (Note: Not valid until Storage System primary HSV200 controller is elected): FALSE
Single power supply HSV200 controller: FALSE
revision - Structure revision number: 2 [0x02]
count - Event specific information size in bytes: 180 [0xb4]
sequence_number - Sequence number assigned to the event: 125609 [0x01eaa9]
sw_version - HSV200 controller software version number string: 6000
baselevel_id - HSV200 controller baselevel build string: CR0D63
ctrlr_model_id - HSV200 controller model string: HSV200
reporting_ctrlr - Storage System Management Interface Handle of HSV200 controller that reported the event: Noid: 0 IdType: 7 IdLength: 8 UUID: 5005-08b4-0010-8a4d-0000-0000-0000-0000
report_time - Time event was reported: Date: 27-Sep-2011 Time: 09:24:29:877
report_location - Location of event report call: 1413556 [0x1591b4]
header (Header Information)
** NOTE: The following is part of a UNION with more than one interpretation.
You will need to determine which union value is relevant.
** START UNION: ( u - Event Code Union ) **
ec (Event Code)
eiptype - Event Information Packet Type Code: 8 [0x08]
cac - Corrective Action Code: 74 [0x4a]
Corrective Action: Unable to communicate through a Fibre Channel link to a Fibre Channel port. This may be caused by a missing Fibre connection to an HSV200 controller Host Port or Drive Enclosure, faulty GBIC, faulty Drive Enclosure, faulty Fibre Channel Cable, faulty Drive Enclosure I/O module, or faulty Fibre Channel Switch. This is a preemptive action warning, no immediate action is necessary.
evnum - Event Number: 1 [0x01]
scid - HSV200 Controller Software Component Identification: 6 [0x06]
** UNION OR: ( u - Event Code Union ) **
value - Event Code Value: 100747784 [0x06014a08]
** END UNION: ( u - Event Code Union ) **
revision - Packet revision number: 3 [0x03]
type - Packet type: 8 [0x08]
count - Number of bytes in packet: 116 [0x74]
cerp_id - HSV200 controller enclosure rear panel Fibre Channel port: DP-1B
other_cerp_id - HSV200 controller enclosure rear panel Fibre Channel port attached to the physical disk drive or mirror port:
peb[0] (Fibre Channel port Event Blocks)
type - Error type code: 3 [0x03]
context - Error context: 3735879684 [0xdead0004]
peb[1] (Fibre Channel port Event Blocks)
type - Error type code: 3 [0x03]
context - Error context: 3735879684 [0xdead0004]
peb[2] (Fibre Channel port Event Blocks)
type - Error type code: 3 [0x03]
context - Error context: 3735879684 [0xdead0004]
peb[3] (Fibre Channel port Event Blocks)
type - Error type code: 3 [0x03]
context - Error context: 3735879684 [0xdead0004]
peb[4] (Fibre Channel port Event Blocks)
type - Error type code: 3 [0x03]
context - Error context: 3735879684 [0xdead0004]
peb[5] (Fibre Channel port Event Blocks)
type - Error type code: 3 [0x03]
context - Error context: 3735879684 [0xdead0004]
peb[6] (Fibre Channel port Event Blocks)
type - Error type code: 3 [0x03]
context - Error context: 3735879684 [0xdead0004]
peb[7] (Fibre Channel port Event Blocks)
type - Error type code: 3 [0x03]
context - Error context: 3735879684 [0xdead0004]
peq_prod_index - Producer index: 6 [0x06]
peq_frz_prod_index - Error idle or freeze producer index: 6 [0x06]
failure_cause - Code indicating path to link failure: 3 [0x03]
peq_cons_index - Consumer index: 5 [0x05]
reserved1 - Reserved: 0 [0x00]
time - Used to represent a retry time or other time based element in the event.: 16 [0x10]
other_port - HSV200 controller internal Fibre Channel port number: 0 [0x00]
port - HSV200 controller internal Fibre Channel port number: 1 [0x01]
recovery (Loop Recovery Operations)
progress - EWE Step for recovery process: 0 [0x00]
shelf - Physical Shelf being evaluated.: 0 [0x00]
slot - Physical Slot being evaluated.: 0 [0x00]
cab - Cabinet rack being evaluated.: 0 [0x00]
*** End of Data ***
说是光纤通道不通,但是具体在哪个位置不通,小弟看不明白,谢谢。 |
|