BK200E 连接存储HP EVA400问题

coologin

目前,我的BK200E连接存储,但是主机连接BK200E,主机上发现不了存储,本人对存储交换机工作模式不太了解.

资料了很多资料,说什么主机上光纤模式不同(pt2pt),又说需要对存储进行配置

在BK200E
sw77:admin> switchshow
switchName:     sw77
switchType:     34.0
switchState:    Online
switchMode:     Native
switchRole:     Principal
switchDomain:   1
switchId:       fffc01
switchWwn:      10:00:00:05:1e:02:9b:bf
zoning:         ON (cfg_psd)
switchBeacon:   OFF

Area Port Media Speed State     Proto
=====================================

  0   0   id    N4   Online           L-Port  1 private                             --->连接存储HP EVA4400
  1   1   id    N4   Online           F-Port  50:01:43:80:09:77:cf:3e     -->HP2 RX6600A
  2   2   id    N4   No_Light
  3   3   id    N4   Online           F-Port  50:01:43:80:09:77:cc:66    --->HP1 RX6600B

目前存储接的线亮黄灯.

在HP-UX下没找到存储上分配的硬盘


root@hp1:/#fcmsutil /dev/fcd0

                           Vendor ID is = 0x1077
                           Device ID is = 0x2422
            PCI Sub-system Vendor ID is = 0x103C
                   PCI Sub-system ID is = 0x12D6
                               PCI Mode = PCI-X 66 MHz
                       ISP Code version = 5.3.2
                       ISP Chip version = 3
                               Topology = PTTOPT_FABRIC
                             Link Speed = 4Gb
                     Local N_Port_id is = 0x010300
                  Previous N_Port_id is = None
            N_Port Node World Wide Name = 0x500143800977cc67
            N_Port Port World Wide Name = 0x500143800977cc66
            Switch Port World Wide Name = 0x200300051e029bbf
            Switch Node World Wide Name = 0x100000051e029bbf
              N_Port Symbolic Port Name = hp1_fcd0
              N_Port Symbolic Node Name = hp1_HP-UX_B.11.31
                           Driver state = ONLINE
                       Hardware Path is = 0/4/2/0
                     Maximum Frame Size = 2048
         Driver-Firmware Dump Available = NO
         Driver-Firmware Dump Timestamp = N/A
                                   TYPE = PFC
                         NPIV Supported = YES
                         Driver Version = @(#) fcd B.11.31.1009 May  9 2010


man fcmsutil

查看到一些属性


UNINITIALIZED.
      There is no connectivity to the host bus adapter
      port or the topology could not be determined.

UNKNOWN.
      The Fibre Channel driver has returned a topology
      code that the utility does not understand.

PRIVATE_LOOP.
      The host bus adapter is attached to a
      loop/loopback hood.

PUBLIC_LOOP.
      The host adapter is attached to a loop connected
      to a Fibre Channel switch.

IN_PTTOPT_NPORT/PTTOPT_NPORT.
      The host bus adapter has come up in a point to
      point topology.  This topology can be an error if
      the card was expected to come up in loop topology.
      Not legal in most cases.

PTTOPT_FABRIC.
      The host bus adapter has come up in a point to
      point topology when connected through a Fibre
      Channel switch.  This topology can be an error if
      the card was expected to come up in loop topology.

The following driver states are defined:

LOOPBACK_STATE.
      The host bus adapter is in the loop back test

milujite

口类型当然要匹配啊。个人经验，最好都统一成pt2pt吧。Fport对应的是pt2pt，你这是Lport。手动修改下存储的口类型为pt2pt看看。主机也修改卡的模式为PT2PT，交换机也设置成F-port，如果无法自动更改类型，手动设置portcfggport。

从你这贴出来的看，主机上口类型已经是PT2PT了。剩下的就设置存储和交换机，一般交换机是自动协商口类型的，一般不需要手动指定交换机口类型。基本上是存储修改PT2PT就好了。

参考这个：
portCfgGport
Designates a port as a G_Port; removes G_Port designation.
Synopsis portcfggport [slot/]port,mode
Description Use this command to designate a port as a G_Port. After successful execution of this command,
the switch attempts to initialize the specified port as an F_Port only, and does not attempt loop
initialization (FL_Port) on the port. A port designated as a G_Port can become an E_Port. This
configuration can be cleared but not set on VE/VEX_Ports. Changes made by this command are
persistent across switch reboots or power cycles.
Note The execution of this command is subject to Virtual Fabric or Admin Domain restrictions that may
be in place. Refer to chapter 1, "Using Fabric OS commands" and Appendix A, "Command
Availability" for details.
Operands This command has the following operands:
slot For bladed systems only, specify the slot number of the port to be configured,
followed by a slash (/).
port Specify the port to be configured, relative to its slot for bladed systems. Use
switchShow to display a list of valid ports.
mode Specify a value of 1 to designate the port as a G_Port or specify a value of 0
to remove the G_Port designation from the port. A value of 0 is the default
port state. Mode must be preceded by a comma. This operand is required.
Examples To configure port as a locked G_Port:
switch:admin> portcfggport 1/3, 1