论坛徽章:: 0

电梯直达

1楼 [收藏(0)] [报告]

发表于 2012-05-18 21:45 |只看该作者 |倒序浏览

本帖最后由 wenlan88 于 2012-05-18 21:46 编辑

##### FriendlyARM BIOS 2.0 for 2440 #####
[x] format NAND FLASH for Linux
[v] Download vivi
[k] Download linux kernel
[y] Download root_yaffs image
[a] Absolute User Application
[n] Download Nboot for WinCE
[l] Download WinCE boot-logo
[w] Download WinCE NK.bin
[d] Download & Run
[z] Download zImage into RAM
[g] Boot linux from RAM
[f] Format the nand flash
Boot the system
Set the boot parameters
Backup NAND Flash to HOST through USB(upload)
[r] Restore NAND Flash from HOST through USB
[q] Goto shell of vivi
Version: 1026-2K
Enter your selection: g
Copy linux kernel from 0x00060000 to 0x30008000, size = 0x00500000 ... done
zImage magic = 0x016f2818
Setup linux parameters at 0x30000100
linux command line is: "noinitrd root=/dev/mtdblock3 init=/linuxrc console=ttySA
C0"
MACH_TYPE = 1999
NOW, Booting Linux......
Uncompressing Linux.............................................................
................................................................ done, booting t
he kernel.
Linux version 2.6.32.59 (root@localhost.localdomain) (gcc version 4.2.2) #1 Sun
May 13 16:35:26 CST 2012
CPU: ARM920T [41129200] revision 0 (ARMv4T), cr=c0007177
CPU: VIVT data cache, VIVT instruction cache
Machine: SMDK2440
ATAG_INITRD is deprecated; please update your bootloader.
Memory policy: ECC disabled, Data cache writeback
CPU S3C2440A (id 0x32440001)
S3C24XX Clocks, (c) 2004 Simtec Electronics
S3C244X: core 405.000 MHz, memory 101.250 MHz, peripheral 50.625 MHz
CLOCK: Slow mode (1.500 MHz), fast, MPLL on, UPLL on
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 16256
Kernel command line: noinitrd root=/dev/mtdblock3 init=/linuxrc console=ttySAC0
PID hash table entries: 256 (order: -2, 1024 bytes)
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 64MB = 64MB total
Memory: 60816KB available (3596K code, 293K data, 144K init, 0K highmem)
Hierarchical RCU implementation.
NR_IRQS:99
irq: clearing subpending status 00000003
irq: clearing subpending status 00000002
Console: colour dummy device 80x30
console [ttySAC0] enabled
Calibrating delay loop... 201.93 BogoMIPS (lpj=504832)
Mount-cache hash table entries: 512
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
S3C Power Management, Copyright 2004 Simtec Electronics
S3C2440: Initialising architecture
S3C2440: IRQ Support
S3C24XX DMA Driver, (c) 2003-2004,2006 Simtec Electronics
DMA channel 0 at c4808000, irq 33
DMA channel 1 at c4808040, irq 34
DMA channel 2 at c4808080, irq 35
DMA channel 3 at c48080c0, irq 36
S3C244X: Clock Support, DVS off
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
s3c-i2c s3c2440-i2c: slave address 0x10
s3c-i2c s3c2440-i2c: bus frequency set to 98 KHz
s3c-i2c s3c2440-i2c: i2c-0: S3C I2C adapter
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 204
TCP reno registered
NET: Registered protocol family 1
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
RPC: Registered tcp NFSv4.1 backchannel transport module.
NetWinder Floating Point Emulator V0.97 (extended precision)
msgmni has been set to 118
io scheduler noop registered
io scheduler anticipatory registered (default)
io scheduler deadline registered
io scheduler cfq registered
Console: switching to colour frame buffer device 30x40
fb0: s3c2410fb frame buffer device
lp: driver loaded but no devices found
ppdev: user-space parallel port driver
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
s3c2440-uart.0: s3c2410_serial0 at MMIO 0x50000000 (irq = 70) is a S3C2440
s3c2440-uart.1: s3c2410_serial1 at MMIO 0x50004000 (irq = 73) is a S3C2440
s3c2440-uart.2: s3c2410_serial2 at MMIO 0x50008000 (irq = 76) is a S3C2440
brd: module loaded
loop: module loaded
Uniform Multi-Platform E-IDE driver
ide-gd driver 1.18
ide-cd driver 5.00
S3C24XX NAND Driver, (c) 2004 Simtec Electronics
s3c24xx-nand s3c2440-nand: Tacls=3, 29ns Twrph0=7 69ns, Twrph1=3 29ns
s3c24xx-nand s3c2440-nand: NAND soft ECC
NAND device: Manufacturer ID: 0xec, Chip ID: 0xda (Samsung NAND 256MiB 3,3V 8-bi
t)
Scanning device for bad blocks
Bad eraseblock 21 at 0x0000002a0000
Bad eraseblock 238 at 0x000001dc0000
Bad eraseblock 674 at 0x000005440000
Bad eraseblock 777 at 0x000006120000
Bad eraseblock 979 at 0x000007a60000
Bad eraseblock 1339 at 0x00000a760000
Bad eraseblock 1571 at 0x00000c460000
Bad eraseblock 2006 at 0x00000fac0000
Creating 3 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x000000000000-0x000000030000 : "supervivi"
mtd: partition "supervivi" doesn't end on an erase block -- force read-only
0x000000050000-0x000000250000 : "Kernel"
mtd: partition "Kernel" doesn't start on an erase block boundary -- force read-o
nly
0x000000250000-0x000003ffc000 : "root"
mtd: partition "root" doesn't start on an erase block boundary -- force read-onl
y
dm9000 Ethernet Driver, V1.31
usbmon: debugfs is not available
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
s3c2410-ohci s3c2410-ohci: S3C24XX OHCI
s3c2410-ohci s3c2410-ohci: new USB bus registered, assigned bus number 1
s3c2410-ohci s3c2410-ohci: irq 42, io mem 0x49000000
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
usbcore: registered new interface driver libusual
usbcore: registered new interface driver usbserial
USB Serial support registered for generic
usbcore: registered new interface driver usbserial_generic
usbserial: USB Serial Driver core
USB Serial support registered for FTDI USB Serial Device
usbcore: registered new interface driver ftdi_sio
ftdi_sio: v1.5.0:USB FTDI Serial Converters Driver
USB Serial support registered for pl2303
usbcore: registered new interface driver pl2303
pl2303: Prolific PL2303 USB to serial adaptor driver
mice: PS/2 mouse device common for all mice
S3C24XX RTC, (c) 2004,2006 Simtec Electronics
S3C2410 Watchdog Timer, (c) 2004 Simtec Electronics
s3c2410-wdt s3c2410-wdt: watchdog inactive, reset disabled, irq enabled
Advanced Linux Sound Architecture Driver Version 1.0.21.
ALSA device list:
  No soundcards found.
TCP cubic registered
NET: Registered protocol family 17
drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
Root-NFS: No NFS server available, giving up.
VFS: Unable to mount root fs via NFS, trying floppy.
VFS: Cannot open root device "mtdblock3" or unknown-block(2,0)
Please append a correct "root=" boot option; here are the available partitions:
1f00          192 mtdblock0 (driver?)
1f01          2048 mtdblock1 (driver?)
1f02          63152 mtdblock2 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)
Backtrace:
[<c00308f0>] (dump_backtrace+0x0/0x10c) from [<c0030a30>] (dump_stack+0x18/0x1c)

r6:c002685c r5:c388f01d r4:c03d58ac
[<c0030a18>] (dump_stack+0x0/0x1c) from [<c004f15c>] (panic+0x4c/0x134)
[<c004f110>] (panic+0x0/0x134) from [<c0009150>] (mount_block_root+0x1d4/0x21c)
r3:00000000 r2:c38355ec r1:c381bf60 r0:c0353e3c
[<c0008f7c>] (mount_block_root+0x0/0x21c) from [<c000925c>] (mount_root+0xc4/0xf
c)
[<c0009198>] (mount_root+0x0/0xfc) from [<c0009400>] (prepare_namespace+0x16c/0x
1cc)
r5:c0026814 r4:c03d4ff4
[<c0009294>] (prepare_namespace+0x0/0x1cc) from [<c0008940>] (kernel_init+0xe0/0
x11
r5:c0025bf8 r4:c03d4dd8
[<c0008860>] (kernel_init+0x0/0x11 from [<c0051f24>] (do_exit+0x0/0x5ac)
r5:00000000 r4:00000000

Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0)

我按照：http://bbs.chinaunix.net/thread-3633947-1-1.html的说明来移植内核跟文件系统！
说是无法挂载rootfs！大侠们帮帮忙呀！！不甚感激！