免费注册 查看新帖 |

Chinaunix

  平台 论坛 博客 文库
12下一页
最近访问板块 发新帖
查看: 2733 | 回复: 19
打印 上一主题 下一主题

E250无法启动问题,请教 [复制链接]

论坛徽章:
0
跳转到指定楼层
1 [收藏(0)] [报告]
发表于 2004-09-07 13:40 |只看该作者 |倒序浏览
各位大侠:
    公司有台Sun EnterPrise 250,配置如下:
    CPU 400MH*1
      内存 256M*1
      硬盘 SCSI 18G*1
      
      1、原来安装Solaris 8 可以正常使用。经过一段时间没有使用,再次打开后显示器无反应。
    2、通过TIP上去后,发现系统启动到
    SunOS Release 5.8 Version Generic 64-bit
      CopyRight 1998-2003 Sun Microsystem ......
      Use is subject to License terms.
      再下面一行有个 "/" 转来转去的,大概转了几圈就停了,系统也没有反应,进入OK状态都不行。
    3、通过TIP进入这台机器的OK状态,boot后还是这种情况。然后 boot cdrom 用Solaris8 software 1 of 2引导,也是启动到相同地点,就停止相应。
    4、通过Solaris9 1 of 2 引导情况同上。
    5、更换硬盘2块,情况依旧存在。
    6、暂时没有好办法了,上CU。

    请问各位是否遇到过类似情况,或者高手给些好的建议,如何才能解决这个问题。
    十分感激!

论坛徽章:
0
2 [报告]
发表于 2004-09-07 13:51 |只看该作者

E250无法启动问题,请教

诊断级别设为max,将钥匙开到诊断位置,看看POST有什么错误信息没有? 然后到OK下,运行show-post-results看看

论坛徽章:
0
3 [报告]
发表于 2004-09-07 14:50 |只看该作者

E250无法启动问题,请教

Hardware Power ON

CPU0 has assumed the role of Boot CPU

@(#) Sun (TM) Enterprise 250  3.16 Version 1 created 1999/04/19 07:55
Online:  CPU0  Ultra-II (v10.0) 4:1 2048KB 2-2 ECache MCap 7
Offline: CPU1 (MD'e
Set-Speed Reset

CPU0 has assumed the role of Boot CPU

@(#) Sun (TM) Enterprise 250  3.16 Version 1 created 1999/04/19 07:55
Online:  CPU0  Ultra-II (v10.0) 4:1 2048KB 2-2 ECache MCap 7
Offline: CPU1 (MD'ed)
Probing keyboard for L1/L1-D...Done
Executing Power On SelfTest w/%o0 = 0000.0000.0010.1002

0>;
0>;@(#) Sun UltraSPARC-II 2-way UPA/PCI POST 6.0.9 04/19/99: 07:57
0>;INFO: Processor 0 is master CPU.
0>; <00>; Init System BSS
0>; <00>; NVRAM Battery Detect Test
0>; <00>; NVRAM Scratch Addr Test
0>; <00>; DMMU TLB Tag Access Test
0>; <00>; DMMU TLB RAM Access Test
0>; <00>; Probe Ecache
0>;INFO: 2048KB Ecache
0>; <00>; Ecache RAM Addr Test
0>; <00>; Ecache Tag Addr Test
0>; <00>; Invalidate Ecache Tags
0>; <00>; SC Dtag Probe
0>;INFO: Dtag supports up to  2MB Ecache
0>;INFO: Processor 1 is missing or disabled.
0>; <00>; Init SC Regs
0>; <00>; SC Address Reg Test
0>; <00>; SC Reg Index Test
0>; <00>; SC Regs Test
0>; <00>; SC Dtag RAM Addr Test
0>; <00>; SC Dtag Init
0>; <00>; Init SC Regs
0>; <00>; SC Cache Size Init
0>; <00>; Synch up Processor Ecache Sizes
0>; <00>; Probe Memory
0>;INFO:  256MB Bank 0
0>;INFO: No memory detected in Bank 1
0>;INFO: No memory detected in Bank 2
0>;INFO: No memory detected in Bank 3
0>; <00>; Test Memory Data Lines
0>; <00>; Test Memory Address Lines
0>; <00>; Malloc Post Memory
0>; <00>; Init Post Memory
0>; <00>; Map PROM/STACK/NVRAM in DMMU
0>; <00>; Memory Stack Test
0>; <00>; Init Memory
0>; <00>; ECC Memory Addr Test
0>; <00>; V9 Instruction Test
0>; <00>; Memory Addr w/ Ecache Test
0>; <00>; Block Memory Addr Test
0>; <00>; Copy Post to Memory
0>; <00>; Map/Exec POST from Memory
0>; <00>; Map alternate CPUs
0>; <00>; Init Memory
0>;INFO:  256MB Bank 0
0>;INFO: No memory in Bank 1
0>;INFO: No memory in Bank 2
0>;INFO: No memory in Bank 3
0>; <00>; OBP Memory Test
0>; <1f>; Init Psycho
0>; <1f>; Psycho Cntl and UPA Reg Test
0>; <1f>; Psycho DMA Scoreboard Reg Test
0>; <1f>; Psycho Perf Cntl Reg Test
0>; <1f>; PIO Decoder and BCT Test
0>; <1f>; PCI Byte Enable Test
0>; <1f>; Counter/Timer Limit Regs Test
0>; <1f>; Timer Increment Test
0>; <1f>; Timer Reload Test
0>; <1f>; Timer Periodic Test
0>; <1f>; Mondo Int Map (short) Reg Test
0>; <1f>; Mondo Int Set/Clr Reg Test
0>; <1f>; Psycho IOMMU Regs Test
0>; <1f>; Psycho IOMMU RAM NTA Test
0>; <1f>; Psycho IOMMU CAM NTA Test
0>; <1f>; Psycho IOMMU RAM Address Test
0>; <1f>; Psycho IOMMU CAM Address Test
0>; <1f>; IOMMU TLB Compare Test
0>; <1f>; IOMMU TLB Flush Test
0>; <1f>; Stream Buff A Control Reg Test
0>; <1f>; Psycho ScacheA Page Tag Addr Test
0>; <1f>; Psycho ScacheA Line Tag Addr Test
0>; <1f>; Psycho ScacheA RAM Addr Test
0>; <1f>; Psycho ScacheA Page Tag NTA Test
0>; <1f>; Psycho ScacheA Line Tag NTA Test
0>; <1f>; Psycho ScacheA Err Status NTA Test
0>; <1f>; Psycho ScacheA RAM NTA Test
0>; <1f>; Stream Buff B Control Reg Test
0>; <1f>; Psycho ScacheB Page Tag Addr Test
0>; <1f>; Psycho ScacheB Line Tag Addr Test
0>; <1f>; Psycho ScacheB RAM Addr Test
0>; <1f>; Psycho ScacheB Page Tag NTA Test
0>; <1f>; Psycho ScacheB Line Tag NTA Test
0>; <1f>; Psycho ScacheB Err Status NTA Test
0>; <1f>; Psycho ScacheB RAM NTA Test
0>; <1f>; PBMA PCI Config Space Regs Test
0>; <1f>; PBMA Control/Status Reg Test
0>; <1f>; PBMA Diag Reg Test
0>; <1f>; PBMB PCI Config Space Regs Test
0>; <1f>; PBMB Control/Status Reg Test
0>; <1f>; PBMB Diag Reg Test
0>; <1f>; Consist DMA Rd, IOMMU miss Lpbk Test
0>;STATUS=PASSED


Power On Selftest Completed
    Status  = 0000.0000.0000.0000   ffff.ffff.f00b.2e08   ffdf.ffff.0bd1.1111
POST Reset

CPU0 has assumed the role of Boot CPU

@(#) Sun (TM) Enterprise 250  3.16 Version 1 created 1999/04/19 07:55
Online:  CPU0  Ultra-II (v10.0) 4:1 2048KB 2-2 ECache MCap 7
Offline: CPU1 (MD'ed)
Setting system ECache size to 2048KB
Clearing DTAGS...Done
Programming memory controller for 10ns/100MHz UPA timing
Clearing E-Cache Tags...Done
Clearing I/D TLBs...Done
Probing Memory...Done
HiMem base = 0000.0000.0000.0000   size = 0000.0000.1000.0000
Clearing Memory...including Unix Retained Memory...Done
MMUs ON
Copying ROM to RAM...Done
RAM CRC = 0000.0000.73eb.2e26;  ROM CRC = 0000.0000.73eb.2e26
Decompressing into Memory...0000.0000.0004.4b8c (275KB)...Done
Size = 0000.0000.0008.48e0 (531KB)
Starting Forth kernel at 0000.0000.f005.8cbc
ttya initialized
SC Control: EWP:0 IAP:0 FATAL:0 WAKEUP:0 BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0
System Memory Configuration:
  Bank #0  64  64  64  64 : 256 MB   [Available  256MB @ 0 ]
  Bank #1   0   0   0   0 :   0 MB   [Not In Use]
  Bank #2   0   0   0   0 :   0 MB   [Not In Use]
  Bank #3   0   0   0   0 :   0 MB   [Not In Use]
Environmental monitor: enabled
Probing Floppy: No drives detected
Initializing RSC...Done.
Primary UPA probing
Probing all UPA slots ................................Done.
At UPA Slot  0 Created Node(s)...SUNW,UltraSPARC-II
At UPA Slot 1f Created Node(s)...pci pci

Primary I/O probing
Probing /pci@1f,4000 at Device 1  network
Probing /pci@1f,4000 at Device 3  scsi disk tape scsi disk tape
Probing /pci@1f,4000 at Device 2  Nothing there
Probing /pci@1f,4000 at Device 4  Nothing there
Probing /pci@1f,4000 at Device 5  Nothing there
Probing /pci@1f,2000 at Device 0  This slot excluded from probing...
Probing /pci@1f,2000 at Device 1  Nothing there
Probing /pci@1f,2000 at Device 2  Nothing there
Probing /pci@1f,2000 at Device 3  Nothing there
Probing /pci@1f,2000 at Device 4  Nothing there
Probing /pci@1f,2000 at Device 5  Nothing there
Post-probe Cheerio fixups
Can't open input device.
screen not found.
Can't open input device.
Keyboard not present.  Using ttya for input and output.
Keyboard not present.  Using ttya for input and output.
SC Control: EWP:0 IAP:0 FATAL:0 WAKEUP:0 BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0
System Memory Configuration:
  Bank #0  64  64  64  64 : 256 MB   [Available  256MB @ 0 ]
  Bank #1   0   0   0   0 :   0 MB   [Not In Use]
  Bank #2   0   0   0   0 :   0 MB   [Not In Use]
  Bank #3   0   0   0   0 :   0 MB   [Not In Use]
Environmental monitor: enabled
Probing Floppy: No drives detected
Initializing RSC...Done.
Primary UPA probing
Probing all UPA slots ................................Done.
At UPA Slot  0 Created Node(s)...SUNW,UltraSPARC-II
At UPA Slot 1f Created Node(s)...pci pci

Primary I/O probing
Probing /pci@1f,4000 at Device 1  network
Probing /pci@1f,4000 at Device 3  scsi disk tape scsi disk tape
Probing /pci@1f,4000 at Device 2  Nothing there
Probing /pci@1f,4000 at Device 4  Nothing there
Probing /pci@1f,4000 at Device 5  Nothing there
Probing /pci@1f,2000 at Device 0  This slot excluded from probing...
Probing /pci@1f,2000 at Device 1  Nothing there
Probing /pci@1f,2000 at Device 2  Nothing there
Probing /pci@1f,2000 at Device 3  Nothing there
Probing /pci@1f,2000 at Device 4  Nothing there
Probing /pci@1f,2000 at Device 5  Nothing there
Post-probe Cheerio fixups

Sun (TM) Enterprise 250 (UltraSPARC-II 400MHz), No Keyboard
OpenBoot 3.16, 256 MB memory installed, Serial #15116526.
Ethernet address 8:0:20:e6:a8:ee, Host ID: 80e6a8ee.



Testing /pci@1f,4000/ebus@1
Testing /pci@1f,4000/network@1,1
Testing /pci@1f,4000/ebus@1/su@14,3062f8
Testing /pci@1f,4000/ebus@1/su@14,3083f8
Testing /pci@1f,4000/ebus@1/eeprom@14,0
Testing /pci@1f,4000/ebus@1/ecpp@14,3043bc
Testing /pci@1f,4000/ebus@1/SUNW,envctrltwo@14,600000
Testing /pci@1f,4000/scsi@3
Testing /rsc

Initializing    1 megs of memory at addr           fe00000              
Initializing  254 megs of memory at addr                 0              
Resetting ...


Diagnostics Reset

CPU0 has assumed the role of Boot CPU

@(#) Sun (TM) Enterprise 250  3.16 Version 1 created 1999/04/19 07:55
Online:  CPU0  Ultra-II (v10.0) 4:1 2048KB 2-2 ECache MCap 7
Offline: CPU1 (MD'ed)
Setting system ECache size to 2048KB
Clearing DTAGS...Done
Programming memory controller for 10ns/100MHz UPA timing
Clearing E-Cache Tags...Done
Clearing I/D TLBs...Done
Probing Memory...Done
HiMem base = 0000.0000.0000.0000   size = 0000.0000.1000.0000
Clearing Memory...Done
MMUs ON
Copying ROM to RAM...Done
RAM CRC = 0000.0000.73eb.2e26;  ROM CRC = 0000.0000.73eb.2e26
Decompressing into Memory...0000.0000.0004.4b8c (275KB)...Done
Size = 0000.0000.0008.48e0 (531KB)
Starting Forth kernel at 0000.0000.f005.8cbc
ttya initialized
SC Control: EWP:0 IAP:0 FATAL:0 WAKEUP:0 BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0
System Memory Configuration:
  Bank #0  64  64  64  64 : 256 MB   [Available  256MB @ 0 ]
  Bank #1   0   0   0   0 :   0 MB   [Not In Use]
  Bank #2   0   0   0   0 :   0 MB   [Not In Use]
  Bank #3   0   0   0   0 :   0 MB   [Not In Use]
Environmental monitor: enabled
Probing Floppy: No drives detected
Initializing RSC...Done.
Primary UPA probing
Probing all UPA slots ................................Done.
At UPA Slot  0 Created Node(s)...SUNW,UltraSPARC-II
At UPA Slot 1f Created Node(s)...pci pci

Primary I/O probing
Probing /pci@1f,4000 at Device 1  network
Probing /pci@1f,4000 at Device 3  scsi disk tape scsi disk tape
Probing /pci@1f,4000 at Device 2  Nothing there
Probing /pci@1f,4000 at Device 4  Nothing there
Probing /pci@1f,4000 at Device 5  Nothing there
Probing /pci@1f,2000 at Device 0  This slot excluded from probing...
Probing /pci@1f,2000 at Device 1  Nothing there
Probing /pci@1f,2000 at Device 2  Nothing there
Probing /pci@1f,2000 at Device 3  Nothing there
Probing /pci@1f,2000 at Device 4  Nothing there
Probing /pci@1f,2000 at Device 5  Nothing there
Post-probe Cheerio fixups
Can't open input device.
screen not found.
Can't open input device.
Keyboard not present.  Using ttya for input and output.
Keyboard not present.  Using ttya for input and output.
SC Control: EWP:0 IAP:0 FATAL:0 WAKEUP:0 BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0
System Memory Configuration:
  Bank #0  64  64  64  64 : 256 MB   [Available  256MB @ 0 ]
  Bank #1   0   0   0   0 :   0 MB   [Not In Use]
  Bank #2   0   0   0   0 :   0 MB   [Not In Use]
  Bank #3   0   0   0   0 :   0 MB   [Not In Use]
Environmental monitor: enabled
Probing Floppy: No drives detected
Initializing RSC...Done.
Primary UPA probing
Probing all UPA slots ................................Done.
At UPA Slot  0 Created Node(s)...SUNW,UltraSPARC-II
At UPA Slot 1f Created Node(s)...pci pci

Primary I/O probing
Probing /pci@1f,4000 at Device 1  network
Probing /pci@1f,4000 at Device 3  scsi disk tape scsi disk tape
Probing /pci@1f,4000 at Device 2  Nothing there
Probing /pci@1f,4000 at Device 4  Nothing there
Probing /pci@1f,4000 at Device 5  Nothing there
Probing /pci@1f,2000 at Device 0  This slot excluded from probing...
Probing /pci@1f,2000 at Device 1  Nothing there
Probing /pci@1f,2000 at Device 2  Nothing there
Probing /pci@1f,2000 at Device 3  Nothing there
Probing /pci@1f,2000 at Device 4  Nothing there
Probing /pci@1f,2000 at Device 5  Nothing there
Post-probe Cheerio fixups

Sun (TM) Enterprise 250 (UltraSPARC-II 400MHz), No Keyboard
OpenBoot 3.16, 256 MB memory installed, Serial #15116526.
Ethernet address 8:0:20:e6:a8:ee, Host ID: 80e6a8ee.



Initializing    1 megs of memory at addr           feca000              
Initializing    1 megs of memory at addr           fe00000              
Initializing  254 megs of memory at addr                 0              
Rebooting with command: boot
Boot device: net  File and args:
Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
AutoNegotiation Timeout.
Check Cable or Contact your System Administrator.
Link Down.
Setting up Network Link and Speed.
Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
AutoNegotiation Timeout.
Check Cable or Contact your System Administrator.
Link Down.
Network Link Setup Failed.
Please Check Cable and Try Again.
Setting up Network Link and Speed.
Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
AutoNegotiation Timeout.
Check Cable or Contact your System Administrator.
Link Down.
Network Link Setup Failed.
Please Check Cable and Try Again.
Timeout waiting for ARP/RARP packet
Setting up Network Link and Speed.
Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
AutoNegotiation Timeout.
Check Cable or Contact your System Administrator.
Link Down.
Network Link Setup Failed.
Please Check Cable and Try Again.
Setting up Network Link and Speed.
Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
AutoNegotiation Timeout.
Check Cable or Contact your System Administrator.
Link Down.
Network Link Setup Failed.
Please Check Cable and Try Again.
Timeout waiting for ARP/RARP packet
Setting up Network Link and Speed.
Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
AutoNegotiation Timeout.
Check Cable or Contact your System Administrator.
Link Down.
Network Link Setup Failed.
Please Check Cable and Try Again.
Setting up Network Link and Speed.
Using Onboard Transceiver - Timeout waiting for AutoNegotiation Status to be updated.
Timeout reading Link status. Check cable and try again.
Timeout waiting for AutoNegotiation Status to be updated.

下面就连续不停的报错说网络没有连接了
我不认为这是系统无法启动的原因
请帮忙看看!
谢谢!

论坛徽章:
0
4 [报告]
发表于 2004-09-07 15:05 |只看该作者

E250无法启动问题,请教

这是show-post-results结果
ok show-post-results
Power On Selftest not run on last reset
Persistent/saved POST results are:
Status 0=Pass, Non-Zero=Fail (%o0): 0
Message String               (%o1):
Board Descriptor             (%o2): ffdfffff0bd11111

论坛徽章:
0
5 [报告]
发表于 2004-09-07 15:11 |只看该作者

E250无法启动问题,请教

setenv diag-switch? false

论坛徽章:
0
6 [报告]
发表于 2004-09-07 15:36 |只看该作者

E250无法启动问题,请教

还是不可以,奇怪的是
printenv里面
boot-device           disk:a disk net                disk net
但是启动时却直接从网络
没有发现硬盘啊?!

论坛徽章:
0
7 [报告]
发表于 2004-09-07 16:07 |只看该作者

E250无法启动问题,请教

最大化自检的话
应该设置成 setenv diag-device disk
                  setenv diag-switch? true
这样就不会启动网络了!



还有听你的描述好像是 主板坏了  !

论坛徽章:
0
8 [报告]
发表于 2004-09-07 16:55 |只看该作者

E250无法启动问题,请教

按照ywsun的去做
这次到
Boot device: disk  File and args:
Loading ufs-file-system package 1.4 04 Aug 1995 13:02:54.
FCode UFS Reader 1.11 97/07/10 16:19:15.
Loading: /platform/SUNW,Ultra-250/ufsboot
Loading: /platform/sun4u/ufsboot
SunOS Release 5.8 Version Generic_117350-04 64-bit
Copyright 1983-2003 Sun Microsystems, Inc.  All rights reserved.
WARNING: Last shutdown is later than time on time-of-day chip; check date.

就停止相应了
谢谢ywsun,我该如何往下作呢?

论坛徽章:
0
9 [报告]
发表于 2004-09-07 17:21 |只看该作者

E250无法启动问题,请教

Loading ufs-file-system package 1.4 04 Aug 1995 13:02:54.

Sun (TM) Enterprise 250 3.16 Version 1 created 1999/04/19 07:55

WARNING: Last shutdown is later than time on time-of-day chip; check date

是不是时间的错误?

论坛徽章:
0
10 [报告]
发表于 2004-09-08 08:45 |只看该作者

E250无法启动问题,请教

原帖由 "race" 发表:
Loading ufs-file-system package 1.4 04 Aug 1995 13:02:54.

Sun (TM) Enterprise 250 3.16 Version 1 created 1999/04/19 07:55

WARNING: Last shutdown is later than time on time-of-day chip; check d..........

时间错误可能造成系统无法启动吗?
如果是?我该在哪调整?
OK状态下面吗?
谢谢!
您需要登录后才可以回帖 登录 | 注册

本版积分规则 发表回复

  

北京盛拓优讯信息技术有限公司. 版权所有 京ICP备16024965号-6 北京市公安局海淀分局网监中心备案编号:11010802020122 niuxiaotong@pcpop.com 17352615567
未成年举报专区
中国互联网协会会员  联系我们:huangweiwei@itpub.net
感谢所有关心和支持过ChinaUnix的朋友们 转载本站内容请注明原作者名及出处

清除 Cookies - ChinaUnix - Archiver - WAP - TOP