品牌机安装FreeBSD，内置网卡的驱动找不到怎么办？

magicwen

mirnshi 发表于 2013-03-03 13:02
确认是8139? FreeBSD的8139是rl

rl是什么意思？

意思是：ifconfig_rl0  ？这样开头？

lsstarboy

回复 21# magicwen


    报一下ifconfig -l也可以。

mirnshi

magicwen 发表于 2013-03-03 13:09
rl是什么意思？

意思是：ifconfig_rl0  ？这样开头？

驱动的名字。
dmesg | grep rl，看看驱动是否加载了
man rl，可以看到rl对应的网卡

love2006

realteck 8139 不可能没有驱动吧？

sysyinstall->configure->network看不到？

magicwen

回复 24# love2006

嗯 找不到这个选项   只看到netwoking

   

magicwen

同事获取信息如下，还请各位详细指点：
获取到信息如下：
Copyright (c) 1992-2009 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD is a registered trademark of The FreeBSD Foundation.
FreeBSD 8.0-RELEASE #0: Sat Nov 21 15:48:17 UTC 2009
    root@almeida.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Celeron(R) CPU G550 @ 2.60GHz (2594.12-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x206a7  Stepping = 7
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Features2=0x59ae3bf<SSE3,<b1>,DTES64,MON,DS_CPL,VMX,EST,TM2,SSSE3,CX16,xTPR,PDCM,<b17>,SSE4.1,SSE4.2,POPCNT,<b24>,XSAVE>
  AMD Features=0x28100000<NX,RDTSCP,LM>
  AMD Features2=0x1<LAHF>
  TSC: P-state invariant
real memory  = 4294967296 (4096 MB)
avail memory = 3374923776 (3218 MB)
ACPI APIC Table: <THTFPC TONGFANG>
FreeBSD/SMP: Multiprocessor System Detected: 2 CPUs
FreeBSD/SMP: 1 package(s) x 2 core(s)
cpu0 (BSP): APIC ID:  0
cpu1 (AP): APIC ID:  2
ioapic0 <Version 2.0> irqs 0-23 on motherboard
kbd1 at kbdmux0
acpi0: <THTFPC TONGFANG> on motherboard
acpi0: [ITHREAD]
acpi0: Power Button (fixed)
acpi0: reservation of 67, 1 (4) failed
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
acpi_hpet0: <High Precision Event Timer> iomem 0xfed00000-0xfed003ff on acpi0
Timecounter "HPET" frequency 14318180 Hz quality 900
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
vgapci0: <VGA-compatible display> port 0xf000-0xf03f mem 0xf7800000-0xf7bfffff,0xe0000000-0xefffffff irq 16 at device 2.0 on pci0
pci0: <simple comms> at device 22.0 (no driver attached)
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xf7c07000-0xf7c073ff irq 16 at device 26.0 on pci0
ehci0: [ITHREAD]
usbus0: waiting for BIOS to give up control
usbus0: EHCI version 1.0
usbus0: <EHCI (generic) USB 2.0 controller> on ehci0
pci0: <multimedia, HDA> at device 27.0 (no driver attached)
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 28.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> irq 17 at device 28.1 on pci0
pci2: <ACPI PCI bus> on pcib2
re0: <RealTek 8168/8168B/8168C/8168CP/8168D/8168DP/8111B/8111C/8111CP/8111DP PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem 0xf0004000-0xf0004fff,0xf0000000-0xf0003fff irq 17 at device 0.0 on pci2
re0: Using 1 MSI messages
re0: Chip rev. 0x2c000000
re0: MAC rev. 0x00000000
re0: Unknown H/W revision: 0x2c000000
device_attach: re0 attach returned 6
pcib3: <ACPI PCI-PCI bridge> irq 18 at device 28.2 on pci0
pci3: <ACPI PCI bus> on pcib3
pcib4: <ACPI PCI-PCI bridge> irq 18 at device 0.0 on pci3
pci4: <ACPI PCI bus> on pcib4
ehci1: <EHCI (generic) USB 2.0 controller> mem 0xf7c06000-0xf7c063ff irq 23 at device 29.0 on pci0
ehci1: [ITHREAD]
usbus1: waiting for BIOS to give up control
usbus1: EHCI version 1.0
usbus1: <EHCI (generic) USB 2.0 controller> on ehci1
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ATA controller> port 0xf110-0xf117,0xf100-0xf103,0xf0f0-0xf0f7,0xf0e0-0xf0e3,0xf0d0-0xf0df,0xf0c0-0xf0cf irq 19 at device 31.2 on pci0
atapci0: [ITHREAD]
ata2: <ATA channel 0> on atapci0
ata2: [ITHREAD]
ata3: <ATA channel 1> on atapci0
ata3: [ITHREAD]
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
atapci1: <Intel ATA controller> port 0xf0b0-0xf0b7,0xf0a0-0xf0a3,0xf090-0xf097,0xf080-0xf083,0xf070-0xf07f,0xf060-0xf06f irq 19 at device 31.5 on pci0
atapci1: [ITHREAD]
ata4: <ATA channel 0> on atapci1
ata4: [ITHREAD]
ata5: <ATA channel 1> on atapci1
ata5: [ITHREAD]
acpi_button0: <Power Button> on acpi0
acpi_tz0: <Thermal Zone> on acpi0
acpi_tz1: <Thermal Zone> on acpi0
atrtc0: <AT realtime clock> port 0x70-0x77 irq 8 on acpi0
atrtc0: Warning: Couldn't map I/O.
atkbdc0: <Keyboard controller (i8042)> port 0x60,0x64 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
atkbd0: [GIANT-LOCKED]
atkbd0: [ITHREAD]
uart0: <16550 or compatible> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
uart0: [FILTER]
uart1: <16550 or compatible> port 0x2f8-0x2ff irq 3 on acpi0
uart1: [FILTER]
cpu0: <ACPI CPU> on acpi0
est0: <Enhanced SpeedStep Frequency Control> on cpu0
p4tcc0: <CPU Frequency Thermal Control> on cpu0
cpu1: <ACPI CPU> on acpi0
est1: <Enhanced SpeedStep Frequency Control> on cpu1
p4tcc1: <CPU Frequency Thermal Control> on cpu1
pmtimer0 on isa0
orm0: <ISA Option ROM> at iomem 0xce800-0xd37ff pnpid ORM0000 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
ata0 at port 0x1f0-0x1f7,0x3f6 irq 14 on isa0
ata0: [ITHREAD]
ata1 at port 0x170-0x177,0x376 irq 15 on isa0
ata1: [ITHREAD]
ppc0: parallel port not found.
Timecounters tick every 1.000 msec
usbus0: 480Mbps High Speed USB v2.0
usbus1: 480Mbps High Speed USB v2.0
ad4: 476940MB <WDC WD5000AAKX-22ERMA0 17.01H17> at ata2-master UDMA33
ugen0.1: <Intel> at usbus0
uhub0: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus0
ugen1.1: <Intel> at usbus1
uhub1: <Intel EHCI root HUB, class 9/0, rev 2.00/1.00, addr 1> on usbus1
unknown: timeout waiting for read DRQ
unknown: timeout waiting for read DRQ
acd0: DVDROM <HL-DT-ST DVDROM DH41N/S.01> at ata4-master UDMA33
SMP: AP CPU #1 Launched!
Root mount waiting for: usbus1 usbus0
uhub1: 2 ports with 2 removable, self powered
uhub0: 2 ports with 2 removable, self powered
Root mount waiting for: usbus1 usbus0
ugen1.2: <vendor 0x8087> at usbus1
uhub2: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus1
ugen0.2: <vendor 0x8087> at usbus0
uhub3: <vendor 0x8087 product 0x0024, class 9/0, rev 2.00/0.00, addr 2> on usbus0
Root mount waiting for: usbus1 usbus0
uhub3: 4 ports with 4 removable, self powered
uhub2: 6 ports with 6 removable, self powered
ugen1.3: <vendor 0x093a> at usbus1
ums0: <vendor 0x093a product 0x2510, class 0/0, rev 1.10/1.00, addr 3> on usbus1
ums0: 3 buttons and [XYZ] coordinates ID=0
Trying to mount root from ufs:/dev/ad4s2a

love2006

networking就可以

re0: <RealTek 8168/8168B/8168C/8168CP/8168D/8168DP/8111B/8111C/8111CP/8111DP PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem 0xf0004000-0xf0004fff,0xf0000000-0xf0003fff irq 17 at device 0.0 on pci2

应该是re0,networking选择inteface里面, re0设置就可以吧.

用sysinstall设置应该没问题的

magicwen

love2006 发表于 2013-03-04 15:16
networking就可以

re0:  port 0xe000-0xe0ff mem 0xf0004000-0xf0004fff,0xf0000000-0xf0003fff irq 17  ...

奇怪了 选择不了inteface   提示 no network device avliable

选择“FTP” 那些选项就可以

mirnshi

re0: <RealTek 8168/8168B/8168C/8168CP/8168D/8168DP/8111B/8111C/8111CP/8111DP PCIe Gigabit Ethernet> port 0xe000-0xe0ff mem 0xf0004000-0xf0004fff,0xf0000000-0xf0003fff irq 17 at device 0.0 on pci2
re0: Using 1 MSI messages
re0: Chip rev. 0x2c000000
re0: MAC rev. 0x00000000
re0: Unknown H/W revision: 0x2c000000
device_attach: re0 attach returned 6

re识别有问题。换网卡吧。

love2006

在 "/boot/defaults/loader.conf" 中打开Network driver

if_re_load="YES"                 # RealTek 8139C+/8169/8169S/8110S

然后重启再用sysinstall看看出来了没有

手工强制使用if_re网卡驱动
在rc.conf文件中添加
ifconfig_re0="inet 192.168.1.5 netmask 255.255.255.0"
defaultrouter="192.168.1.1"

然后重启机器看看