m4000 xcp 1113 补丁包

lisa_won

下载了微码升级包，为什么readme里不像以前都有升级步骤，请解。

lisa_won

没人知道？

东方蜘蛛

M系的以前有？

lisa_won

是的，我随便找了V890 Flash PROM Update包，readme里就有升级步骤
OBSOLETE Patch-ID# 112186-19
Keywords: sun fire v880 v890
Synopsis: Obsoleted by: 119231-01 Hardware/PROM: Sun Fire V880 / V890 Flash PROM Update
Date: Jan/27/2005


Install Requirements: Additional instructions may be listed below                     
                     
Solaris Release: 8 9

SunOS Release: 5.8 5.9

Unbundled Product: Hardware/PROM

Unbundled Release: OBP 4.15.6, POST 4.15.6, OBDIAG 4.15.6

Xref:

Topic:

Relevant Architectures: sun fire v880 / v890

BugId's fixed with this patch: 5013839 5052771 5053315 5054781 5084913 5101950 5104494 5105537 6178214 6198580 6207590 6211428 6211546

Changes incorporated in this version: 5013839 5054781 5084913 5101950 5104494
5105537 6178214 6198580 6207590
6211428 6211546

Patches accumulated and obsoleted by this patch:

Patches which conflict with this patch:

Patches required with this patch:

Obsoleted by:

Files included with this patch:

                                817-6957-10.pdf, unix.flash-update.README,
                                flash-update-SunFire880-latest
                                flash-update-SunFire880-old,
                                unix.flash-update.SunFire880.sh,
README.112186-19, copyright, 802-3233-25.ps,

Problem Description:

5013839 Update SMS reference to SMS1.5 in SUNWSMSob package
5054781 Need workaround for Cheetah+ erratum #34 in starCat OBP
5084913 MICRON 256MB DIMM FAILURES
5101950 ECACHE Timing is wrong for OPS AFT LBIST TESTS
5104494 Add new Chalupa+ Mb part numbers to Unix flash-update utility
5105537 Performance degradation in V440 jp3.x with SPECcpu2000
6178214 POST abort (ctrl-c) causes multiple errors on some platforms
6198580 RFE to add POST JTAGID info for JAG 3.2
6207590 POST hangs or RED states after installing OBP 4.15.4
6211428 unable to flash obp via boot disk flash-update-SunFire480-latest command
6211546 POST fatals when OBP invokes the POST JTAG/Init sequence

Patch Installation Instructions:
===============================

Intro
-----

    This README is intended for users who wish to upgrade the firmware
    in their Sun Fire V880 / V890.  


Summary of the Patch Installation Process:
------------------------------------------

The installation shall comprise of the following steps

1)  Determine the system's current Flash PROM firmware revision.

2)  Compare the current Flash PROM firmware revision with the available or
    latest Flash PROM firmware revisions.

3)  If the current Flash PROM firmware revision is lower than the latest
    available firmware revision in this patch, then proceed to the next step.
    If NOT, STOP: DO NOT CONTINUE.

4)  Prepare the system for the Flash PROM update

5)  Running the Flash PROM Utility

6)  Verifying successful Flash PROM Update

7)  Restoring the system

  Resume operations


Patch Installation instructions (in detail):
============================================

The required steps are explained in greater detail below.

1)  Determine the System's Current Firmware Revisions
    -------------------------------------------------

    While the OS is running the following command may be used to
    determine the current system firmware revisions;

        /usr/sbin/prtconf -V
        or
        /usr/platform/sun4u/sbin/prtdiag -v | grep OBP

    The firmware revisions may also be determined from the PROM monitor's
    "ok" prompt with the following command;

        .version

2)  Compare the current Flash PROM firmware revision with the available or
    latest Flash PROM firmware revisions.

    Compare the output of the OBP line in the "prtdiag -v" or "prtconf -V"
    output. Find the revision number and compare with the revision on the
    entries below that of the "flash-update-SunFire880-latest" line

      Available Firmware Revisions
      ----------------------------

flash-update-SunFire880-latest:
        OBP 4.15.6 2005/01/06 04:25 Sun Fire 8XX
         Sun Fire[TM] V880/V890 POST 4.15.6 2005/01/06 10:46
        OBDIAG 4.15.6 2005/01/06 04:30  

flash-update-SunFire880-old:
        OBP 4.15.1 2004/06/02 16:06 Sun Fire 8XX
         Sun Fire[TM] V880/V890 POST 4.15.0 2004/05/27 13:23
        OBDIAG 4.15.1 2004/06/02 16:10  

3)  Is the UPGRADE NECESSARY?

    If the current Flash PROM revision matches the version numbers given under
    the flash-update-SunFire880-latest line, then STOP Here. This UPGRADE IS NOT
    NECESSARY.

    If the current Flash PROM firmware revision is lower than the latest
    firmware revision in this patch, then proceed to the next step.

4) Preparing the System
   ---------------------

  a) As root, copy the latest "flash-update" files from the directory
     containing the patch to the root directory as follows:

     # cp flash*latest  /
     # chmod 755 /flash-update*

     In order to boot the binary, it must be located within the root
     partition.  If it is not already located within the root partition
     then move it to /.  If the binary is already located elsewhere
     within the root partition then note the exact filepath so that the
     binary can be booted later.

  b) As root, exit the OS such that the system returns to the PROM's "ok"
     prompt:

     # halt

       ok

  c) Jumper J3003 is factory-set so that the flash PROM is write-enabled.
     There is no need to switch the jumper before flash updating; however,
     you must ensure that the keyswitch is in the Power-on or Diagnostics
     position.  When the key switch is in the locked position the flash
     PROM is write protected.

5)  Running the Flash Update Utility
    --------------------------------

  a) Power on the system

     Wait for the PROM's banner to appear, and then

  b) Use the Stop-A keys (or Break key, if running from a serial line) to
     abort the auto-boot sequence.

     ** NOTE **  If the flash update completes normally then the values
     contained within the system's Non-Volatile RAM (NVRAM) configuration
     variables will be retained.  However, if the update process is some-
     how interrupted then it is possible that any non-default values
     contained in NVRAM will be lost.  For this reason it is recommended
     that you note down on paper the contents of any NVRAM configuration
     variable which has been customized so that they may be manually
     restored at a later time, if necessary.  (Use the PROM's "printenv"
     command to list the variables and their values.)

  c) The system should now display the PROM monitor's "ok" prompt.
     Now boot the Flash update utility as given below:

     CAUTION: Do not boot/run revisions lower than the latest unless you
              are absolutely sure that that is what you want to do!

     ok boot disk /flash-update-SunFire880-latest

     NOTE: If your system's boot device is not "disk" then you will
           have to specify the appropriate devalias (e.g. disk2).
           If the binary is located in a location other than / then
           provide the entire filepath after the boot device.

     Answer the questions as prompted by the utility.


+++++++++++++++++++++ example Flash update follows ++++++++++++++++++++++++
++++++++ Note that this is an example only.  Much of the information ++++++
++++++++ which is displayed by your system will be different from    ++++++
++++++++ what is shown below.                                        ++++++
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++


Standalone Flash PROM Update Utility, Rev. 2.7
                        Ultra(tm) 1
                        Ultra(tm) 2
                        Ultra(tm) 5/10
                        Ultra(tm) 30
                        Ultra(tm) 60 / E220R
                        Ultra(tm) 80 / E420R
                        Ultra(tm) Enterprise(tm) 250
                        Ultra(tm) Enterprise(tm) 450
                        Sun Blade(tm) 100
                        Sun Blade(tm) 1000
                        Sun Fire (tm) 280R
                        Netra(tm) T4
                        Sun Fire (tm) V880

This utility allows you to interactively update the firmware
revisions in specific system Flash PROM components.

Type h for help, q to quit, Return or Enter to continue:

Every precaution should be taken to prevent the loss of system
power during the Flash PROM programming process!

Type h for help, q to quit, Return or Enter to continue:


       Firmware Release(s)                Firmware Release(s)
Currently Existing in the System      Available for Installation  /  Install?
---------------------------------- -------------------------------------------
OBP 4.5.6  2002/01/04 12:30         OBP 4.6.3 2002/05/28 09:09          no
POST 4.5.6 2002/01/04 15:54         POST 4.6.2 2002/05/21 10:41          no

Type sa if you wish to select all available firmware releases for
installation.  Type h for help, quit to exit, or cont to continue: sa


       Firmware Release(s)                Firmware Release(s)
Currently Existing in the System      Available for Installation  /  Install?
---------------------------------- -------------------------------------------
OBP 4.5.6  2002/01/04 12:30         OBP 4.6.3 2002/05/28 09:09         YES
POST 4.5.6 2002/01/04 15:54         POST 4.6.2 2002/05/21 10:41         YES

Type sa if you wish to select all available firmware releases for
installation.  Type h for help, quit to exit, or cont to continue: cont


The Flash programming process is about to begin.

Type h for help, q to quit, Return or Enter to continue:

Erasing the top half of the Flash PROM.
Programming OBP into the top half of the Flash PROM.
Verifying OBP in the top half of the Flash PROM.

Erasing the bottom half of the Flash PROM.
Programming OBP into the bottom half of Flash PROM.
Verifying OBP in the bottom half of the Flash PROM.

Erasing the top half of the Flash PROM.
Programming POST into the top half of Flash PROM.
Verifying POST in the top half of the Flash PROM.

Programming was successful.

Resetting ...


+++++++++++++++++++++ example Flash update ends ++++++++++++++++++++++++++

  Once the PROM's banner reappears then use the Stop-A keys (or Break
  key, if running from a serial line) to abort the auto-boot sequence
  if the system begins to boot.

6)  Verifying successful Flash PROM Update

    Verify from the results of the .version command that the OBP
    version matches the OBP version given above under the
    flash-update-SunFire880-latest entry in Step 2.

7)  Resume operations

    a) Allow the system to auto-boot, or issue the boot command for your
       environment as necessary.

    b) Once the system has rebooted you may wish to remove the Flash Update
       binaries and documents since they will no longer be needed.

       # rm /flash-update*

    c) Remember to remove the files from their original location if
       they were not extracted directly into the root directory.


*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-*-

Special Install Instructions:
-----------------------------

  NOTE 1: If you have the frame buffer Raptor GFXP -04 REV 50
          (part 370-3753-04), you *must* install patch 110126-03 to upgrade the
          FCode in the card **BEFORE** you can do the firmware update. Revisions
          -05 and up of the frame buffer are not affected.

          Failure to install the frame buffer patch (110126-03) will cause
          "FATAL" resets after the firmware update.

  NOTE 2: This utility is *not* OS-dependent.  The list of releases shown under
          the "Solaris Release" and "SunOS Release" sections may not be
          complete: The absence of a valid Solaris Release or SunOS  Release
          from the lists above does not preclude the installation of this patch
          against the hardware.

  NOTE 3: If you are upgrading your system from 4.2.X you will need to
          modify the NVRAM variable, diag-script. OBP version 4.4.7
          introduced a change in the underlying keyvalue assigned to
          the script keywords which will result in the value of
          diag-script being changed. After the firmware upgrade, but
          prior to booting, please execute the following at the "ok"
          prompt:

          ok setenv diag-script normal
          ok reset-all

          This ensures that the system will run the "normal" set of
          diagnostic scripts on all subsequent system resets.

  NOTE 4: Modifications to Diagnostic Operation

          This released version of OpenBoot enables diagnostic execution for all
          power-on and error reset events, **as the new system default.

          **To implement this new policy, behavioral changes to diagnostic
          controls were made to simplify the enabling of diagnostics and
          controlling the level and verbosity of diagnostics.

          A new feature includes a Sun-prescribed mode of diagnostic execution,
          which overrides user-defined settings.  This mode provides service
          personnel with an easy method by which to invoke a predictable
          execution of diagnostics.

          The new standard (default) configuration will increase system boot
          time ( measured from power-on to the 'ok>' prompt ) and messaging
          ( varies by system configuration ) for all 'power-on-reset' and OBP
          detected 'error-reset' events. Increased boot time and messaging is
          largely due to the execution of diagnostics.

          Automated System Recovery (ASR), a form of restoration, is implemented
          at the firmware layer and increases overall system availability when
          diagnostics are enabled.  

          For more specific details regarding these OBP changes, reference the
          pdf document; "OpenBoot[tm] PROM Enhancements for Diagnostic
          Operation", included within this patch ( part 817-6957, July 2004 ).

** WARNING ** WARNING ** WARNING ** WARNING ** WARNING ** WARNING **

*  PLEASE READ THE INSTRUCTIONS CAREFULLY AND ENTIRELY.  PLEASE FOLLOW THE
   INSTRUCTIONS EXACTLY AS THEY ARE STATED.

*  FAILURE TO FOLLOW INSTRUCTIONS COULD EITHER RESULT IN A DEFECTIVE BOARD OR
   UNSUCCESSFUL FLASH PROM UPDATE.

*  THIS IS NOT A STANDARD PATCH in that it does not use the installpatch
   and backoutpatch scripts.

*  THIS PATCH CANNOT BE INSTALLED ON AN ONLINE OPERATING SYSTEM BECAUSE
   THE INSTALL INSTRUCTIONS REQUIRES THAT THE SYSTEM BE BROUGHT DOWN.
   BE SURE TO SCHEDULE DOWN TIME TO INSTALL THIS PATCH.

*  Installation of the firmware included with this patch does NOT
   require any hardware changes if the Flash update completes normally.

*  PLEASE REVIEW NOT ONLY THIS README BUT ALSO ADDITIONAL DOCUMENTATION
   GIVEN.
   The file "802-3233-xx.ps" (where xx stands for the latest numeric
   revision) is a PostScript copy of the "Sun Flash PROM Guide for Workstations
   and Workgroup Servers - Standalone Version", which  provides the following;

   (i) Emergency instructions in the unlikely event that the Flash
        update should fail.

   Note, however, that The Programming Guide was originally written for
   a user who is running the Flash PROM update utility from a bootable
   CDROM, and thus it will not contain the proper boot commands for
   installation of this patch.  Also note that the instructions in
   the document for installing packages are not valid for this patch.

** WARNING ** WARNING ** WARNING ** WARNING ** WARNING ** WARNING **

README -- Last modified date:  Friday, April 29, 2005

dfck001

刚升过M5000的给你个LOG，当时直接把升级包放到U盘然后插在XSCF模块的USB接口上，记得先在U盘建个images目录，升级包放里面
XSCF> getflashimage file:///media/usb_msd/images/FFXCP1113.tar.gz
Existing versions:
        Version                Size  Date
        FFXCP1081.tar.gz   42413986  Thu Feb 19 21:22:36 CST 2009
Warning: About to delete existing versions.
Continue? [y|n]: y
Removing FFXCP1081.tar.gz.
  0MB received
  1MB received
  2MB received
  3MB received
  4MB received
  5MB received
  6MB received
  7MB received
  8MB received
  9MB received
10MB received
11MB received
12MB received
13MB received
14MB received
15MB received
16MB received
17MB received
18MB received
19MB received
20MB received
21MB received
22MB received
23MB received
24MB received
25MB received
26MB received
27MB received
28MB received
29MB received
30MB received
31MB received
32MB received
33MB received
34MB received
35MB received
36MB received
37MB received
38MB received
39MB received
40MB received
41MB received
42MB received
Download successful: 43193 Kbytes in 51 secs (849.125 Kbytes/sec)
Checking file...
MD5: 57dc86407c8014c2b235134a1882d870
XSCF> version -c xcp -v -t
XCP: 1113
OpenBoot PROM : 02.29.0000
XSCF          : 01.11.0003
XSCF> flashupdate -c update -m xcp -s 1113
The XSCF will be reset. Continue? [y|n] :y
Checking the XCP image file, please wait a minute
XCP update is started (XCP version=1113:last version=1081)
OpenBoot PROM update is started (OpenBoot PROM version=02290000)
OpenBoot PROM update has been completed (OpenBoot PROM version=02290000)
XSCF update is started (XSCFU=0,bank=1,XCP version=1113:last version=1081)
XSCF download is started (XSCFU=0,bank=1,XCP version=1113:last version=1081, Firmware Element ID=00:version=01110003:last version=01080001)
XSCF download has been completed (XSCFU=0,bank=1,XCP version=1113:last version=1081, Firmware Element ID=00:version=01110003:last version=01080001)
XSCF download is started (XSCFU=0,bank=1,XCP version=1113:last version=1081, Firmware Element ID=01:version=01110003:last version=01080004)
XSCF download has been completed (XSCFU=0,bank=1,XCP version=1113:last version=1081, Firmware Element ID=01:version=01110003:last version=01080004)
XSCF download is started (XSCFU=0,bank=1,XCP version=1113:last version=1081, Firmware Element ID=02:version=01100001:last version=01080000)
XSCF download has been completed (XSCFU=0,bank=1,XCP version=1113:last version=1081, Firmware Element ID=02:version=01100001:last version=01080000)
XSCF download is started (XSCFU=0,bank=1,XCP version=1113:last version=1081, Firmware Element ID=03:version=01110003:last version=01080004)
XSCF download has been completed (XSCFU=0,bank=1,XCP version=1113:last version=1081, Firmware Element ID=03:version=01110003:last version=01080004)
XSCF download is started (XSCFU=0,bank=1,XCP version=1113:last version=1081, Firmware Element ID=04:version=01110003:last version=01080004)
XSCF download has been completed (XSCFU=0,bank=1,XCP version=1113:last version=1081, Firmware Element ID=04:version=01110003:last version=01080004)
XSCF download is started (XSCFU=0,bank=1,XCP version=1113:last version=1081, Firmware Element ID=05:version=01110000:last version=01080001)
XSCF download has been completed (XSCFU=0,bank=1,XCP version=1113:last version=1081, Firmware Element ID=05:version=01110000:last version=01080001)
XSCF download is started (XSCFU=0,bank=1,XCP version=1113:last version=1081, Firmware Element ID=07:version=01090001:last version=01080004)
XSCF download has been completed (XSCFU=0,bank=1,XCP version=1113:last version=1081, Firmware Element ID=07:version=01090001:last version=01080004)
XSCF update has been completed (XSCFU=0,bank=1,XCP version=1113:last version=1081)
XSCF is rebooting to update the reserve bank
XSCF> execute S10ioxoff  --  complete
Apr  9 02:47:02 ynunicom-xscf0 XSCF[104]: XSCF shutdown sequence start execute K000end  --  complete
execute K100end  --  complete
execute K101end  --  complete
unmount /hcp0/linux
unmount /hcp0/scfprog
unmount /hcp0/gendata  --  complete
unmount /hcp0/remcscm  --  complete
unmount /hcp1/linux  --  complete
unmount /hcp1/scfprog  --  complete
unmount /hcp1/gendata  --  complete
unmount /hcp1/remcscm  --  complete
unmount /hcpcommon/setup  --  complete
unmount /hcpcommon/obp  --  complete
unmount /hcpcommon/tmp  --  complete
unmount /hcpcommon/var
unmount /hcpcommon/scflog1  --  complete
unmount /hcpcommon/scflog2  --  complete
XSCF reset.

The system is g
S
Please stand by while rebooting the system.(15)
Restarting system.


XSCF uboot  01100001  (Feb  3 2011 - 14:43:12)


XSCF uboot  01100001  (Feb  3 2011 - 14:43:12)

SCF board boot factor = a040
    DDR Real size: 256 MB
    DDR: 224 MB

## Booting image at ff800000 ...
   Image Name:   XSCF kernel 01110003 2.6.11.12-s
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    1456945 Bytes =  1.4 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Uncompressing Kernel Image ... OK
## Loading RAMDisk Image at ff980000 ...
   Image Name:   XSCF rootfs 01110003 ,2012/06/29
   Image Type:   PowerPC Linux RAMDisk Image (gzip compressed)
   Data Size:    5629530 Bytes =  5.4 MB
   Load Address: 00000000
   Entry Point:  00000000
   Verifying Checksum ... OK
   Loading Ramdisk to 0baa1000, end 0bfff65a ... OK
Linux version 2.6.11.12-sec (gcc version 3.4.4) #1 Thu May 31 13:19:32 JST 2012

new message buffer at 0f700000 size 1048576

log_buf_len: 1048576

mpc85xx_cds_setup_arch

Built 1 zonelists

Kernel command line: root=/dev/ram rw console=ttyS0,9600 init=/sbin/init_change_root panic=1 mem=224M

OpenPIC Version 1.2 (1 CPUs and 44 IRQ sources) at fbe79000

PID hash table entries: 1024 (order: 10, 16384 bytes)

Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)

Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)

Memory: 218624k available (2188k kernel code, 668k data, 316k init, 0k highmem)

Mount-cache hash table entries: 512 (order: 0, 4096 bytes)

lisa_won

你这个步骤在哪个官方手册里

东方蜘蛛

lisa_won 发表于 2013-04-18 12:03
你这个步骤在哪个官方手册里

LZ啊，890是Fire系列的，能和M系列的一样吗。。。。。

lisa_won

所以这个做的不如以前的好。还得去看手册

东方蜘蛛

lisa_won 发表于 2013-04-18 14:38
所以这个做的不如以前的好。还得去看手册

给你个checklist看看吧，里面有升级步骤。

OPL-Mx000.pdf (455.96 KB, 下载次数: 66)

2013-04-18 14:50 上传

点击文件名下载附件

lisa_won

东方蜘蛛 发表于 2013-04-18 14:51
给你个checklist看看吧，里面有升级步骤。

非常感谢。:wink: