S3C2410编译内核固化后出错

cassiehkx

各位大神，小女子目前在做毕业设计，编译S3C2410内核时候按照手册上讲的一步一步下来，但是出错了，minicom打开显示如下，麻烦帮忙指导下，感激不尽！！！

VIVI version 0.1.4 (root@localhost) (gcc version 2.95.3 20010315 (release)) #0.5MMU table base address = 0x33DFC000
Succeed memory mapping.
NAND device: Manufacture ID: 0xec, Chip ID: 0x76 (Samsung K9D1208V0M)
Found saved vivi parameters.
Press Return to start the LINUX now, any other key for vivi
Copy linux kernel from 0x00030000 to 0x30008000, size = 0x00100000 ... done
zImage magic = 0x016f2818
Setup linux parameters at 0x30000100
linux command line is: "console=ttyS0 root=/dev/nfs nfsroot=192.168.253.1:/arms"MACH_TYPE = 193
NOW, Booting Linux......
Uncompressing Linux........................................................... .Linux version 2.4.18-rmk7-pxa1 (root@localhost) (gcc version 2.95.3 20010315 (r5CPU: ARM/CIRRUS Arm920Tsid(wb) revision 0
Machine: Samsung-SMDK2410
On node 0 totalpages: 16384
zone(0): 16384 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: console=ttyS0 root=/dev/nfs nfsroot=192.168.253.1:/armsys2fDEBUG: timer count 15626
Console: colour dummy device 80x30
Calibrating delay loop... 99.94 BogoMIPS
Memory: 64MB = 64MB total
Memory: 62476KB available (1473K code, 440K data, 76K init)
Dentry-cache hash table entries: 8192 (order: 4, 65536 bytes)
Inode-cache hash table entries: 4096 (order: 3, 32768 bytes)
Mount-cache hash table entries: 1024 (order: 1, 8192 bytes)
Buffer-cache hash table entries: 4096 (order: 2, 16384 bytes)
Page-cache hash table entries: 16384 (order: 4, 65536 bytes)
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
CPU clock = 200.000 Mhz, HCLK = 100.000 Mhz, PCLK = 50.000 Mhz
Initializing S3C2410 buffer pool for DMA workaround
check your kernel config.
USB Function Character Driver Interface - 0.5, (C) 2001, Extenex Corp.
usbctl: Opened for usb-char
usbctl: Started for usb-char
Starting kswapd
devfs: v1.10 (20020120) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
ttyS%d0 at I/O 0x50000000 (irq = 52) is a S3C2410
ttyS%d1 at I/O 0x50004000 (irq = 55) is a S3C2410
ttyS%d2 at I/O 0x50008000 (irq = 5 is a S3C2410
Console: switching to colour frame buffer device 80x30
Installed S3C2410 frame buffer for TFT 640x480 LCD.
pty: 256 Unix98 ptys configured
leds initialized
s3c2410-ts initialized
downS3C2410 Real Time Clock Driver v0.1
PEN DOWN: x: 00000938, y: 00001023
block: 128 slots per queue, batch=32
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx
eth0: cs8900 rev K(3.3 Volts) found at 0xd0000300
cs89x0 media RJ-45, IRQ 37
SCSI subsystem driver Revision: 1.00
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
UDA1341 audio driver initialized
NAND device: Manufacturer ID: 0xec, Chip ID: 0x76 (Samsung NAND 64MiB 3,3V)
NAND_ECC_NONE selected by board driver. This is not recommended !!
Creating 3 MTD partitions on "NAND 64MiB 3,3V":
0x00000000-0x00030000 : "boot"
0x00030000-0x00200000 : "kernel"
0x00200000-0x04000000 : "rootfs"
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xe9000000, IRQ 26
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver usb_mouse
usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
usb.c: registered new driver keyboard
usbkbd.c: :USB HID Boot Protocol keyboard driver
usb.c: registered new driver usblp
printer.c: v0.8:USB Printer Device Class driver
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 4096)
IP-Config: Complete:
      device=eth0, addr=192.168.253.8, mask=255.255.255.0, gw=192.168.253.1,
     host=armsys, domain=, nis-domain=hzlitai.com,
     bootserver=192.168.253.1, rootserver=192.168.253.1, rootpath=
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NetWinder Floating Point Emulator V0.95 (c) 1998-1999 Rebel.com
Looking up port of RPC 100003/2 on 192.168.253.1
Root-NFS: Unable to get nfsd port number from server, using default
Looking up port of RPC 100005/1 on 192.168.253.1
Root-NFS: Unable to get mountd port number from server, using default
hub.c: USB new device connect on bus1/1, assigned device number 2
usb.c: USB device not accepting new address=2 (error=-110)
hub.c: USB new device connect on bus1/1, assigned device number 3
usb.c: USB device not accepting new address=3 (error=-110)
hub.c: USB new device connect on bus1/2, assigned device number 4
usb.c: USB device not accepting new address=4 (error=-110)
hub.c: USB new device connect on bus1/2, assigned device number 5
usb.c: USB device not accepting new address=5 (error=-110)

cassiehkx

肿么都木有人回复，是这个问题太菜鸟了，大家懒得理么  自己顶一下