rp8420告警

yeahzp

查看sl有如下信息：
[mp] MP:VWR (<cr>,<sp>,+,-,?,F,L,J,D,K,R,T,A,C,U,^B) > [mp]  
Log Entry 13187:    02/07/2014 03:36:48
Alert level 3:  Warning
Keyword:  CELL_VRM_VOLT_FLT
The vrm on the specified cell is reporting a voltage fault.
Reporting Entity:  Processor Dependent Hardware Controller located in cabinet 0, slot 1
Physical Location:  Low voltage power supply cabinet 0 slot 1
0x648013c701e00098 0x00ffff01ff01ff43
0x6b0013c701e00099 0x0100000052f454d0

目前状况4个电源接了2个。会不会导致系统有以上报错？

congshuaiok

这个是CELL上的VRM的报错，先PS看下整个cabinet和每个cell看是否有报错，如果某个cell的某个VRM有报错，换掉就行了。

yeahzp

回复 2# congshuaiok


        Enter cell number: 1

HW status for Cell 1 : FAILURE DETECTED

Power status : on, 1.2V Module 0, VRM #1 VOLTAGE FAULT
Boot is not blocked
PDH memory is shared
Processor Compatibility : OK
RIO cable status : connected
RIO cable connection physical location : PCI Domain 1
Core cell is cell 0
Attention Led is off

PDHC status Leds :  ****

CPU Module Slot    0 1 2 3
Populated         P P P P
Local 48V Good    * * * *
Power Enabled     * * * *
Power Good        * * * *

   (* - True, P - Processor, T - Terminator)



DIMMs populated:
0 . . . 4 . . . 8 . . .12 . . .
*   *   *   *                  

                                  1 1 1 1 1 1
VRM's           1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
Present      : * * * * * * * * * * * * * * *
Enabled      : * * * * * * * * * * * * * * *
Pwr Good     :   *   * * * * * * * * * * * *


Front Side Bus Freq.    : 200 MHz
CPU Core Freq.          : 1000 MHz
CPU Part Number         : PA8800

System Boot Rom (SFW) firmware rev  24.004
PDH controller (PDHC) firmware rev 3.031, built THU NOV 09 21:37:37 2006
MICE revision is 1.0

[mp] MP:CM>

确实有错误

yeahzp

[BEGIN] 2014/2/7 15:42:17
cm



                Enter HE to get a list of available commands




[mp] MP:CM> ps


Display detailed status of the selected MP bus device.



The following MP bus devices were found:

+---+----+-----+-------+-------+-----------+

|   |    |     |       |       |           |

|   |    | Sys |       |  IO   | Bulk Pwr  |

|Cab| MP |Bkpln| Cells |Chassis| Supplies  |

| # |M  S|     |0 1 2 3| 0   1 |0 1 2 3 4 5|

+---+----+-----+-------+-------+-----------+

| 0 |*  *|  *  |* *    | *   * |* *     * *|

+---+----+-----+-------+-------+-----------+


You may display detailed power and hardware status for the following items:


    T - Cabinet

    S - System Backplane

    G - MP (Core I/O)

    P - IO Chassis

    C - Cell

        Select Device: t


HW status for rp8420 cabinet : FAILURE DETECTED


Master/Slave failover is Disabled

Power switch is on

Right Door is open

Top Door is closed

Left Door is open


Total Power Available 4000 VA

Total Power Needed 2342 VA

Power Redundancy : redundant

Power Viability : viable



Power Status

---------------+-----+-------+-------+-----------+

               |     |       |       |           |

               | Sys |       |  IO   | Bulk Pwr  |

               |Bkpln| Cells |Chassis| Supplies  |

               |     |0 1 2 3| 0   1 |0 1 2 3 4 5|

---------------+-----+-------+-------+-----------+

Populated     |  *  |* *    | *   * |* *     * *|

Enabled       |  *  |* *    | *   * |* *     * *|

Power OK      |  *  |* *    | *   * |* *     * *|

Warning/Fault |     |  *    |       |           |

Attention LED |     |       |       |           |



AC Line status:

  Line A0 Present

  Line B0 NOT PRESENT

  Line A1 NOT PRESENT

  Line B1 Present


               -- Press <CR> to continue, or 'Q' to Quit --


Front Fan Speed   : high

Rear Fan speed    : high

I/O Bay Fan Speed : high

Temperature state : normal

Main Fan Redundancy   : redundant

I/O Fan Redundancy    : redundant

Overtemp Shutdown Enabled



            |     BPS     |     PCI     |

            |     Fans    |     Fans    |

            | 0 1 2 3 4 5 | 0 1 2 3 4 5 |

+-----------+-------------+-------------+

  Populated | * *     * * | * * * * * * |

  Failing   |             |             |

  Failed    |             |             |


            |              Standby/Main Fans            |

            |                     1 1 1 1 1 1 1 1 1 1 2 |

            | 0 1 2 3 4 5 6 7 8 9 0 1 2 3 4 5 6 7 8 9 0 |

+-----------+-------------------------------------------+

  Populated | * * * * * * * * * * * * * * * * * * * * * |

  Failing   |                                           |

  Failed    |                                           |


            |  Cell Fans |

            |   CPU    C |

            | 0 1 2 3  C |

+-----------+------------+

Cell 0     |            |

  Populated | * * * *  * |

  Failing   |            |

  Failed    |            |

Cell 1     |            |

  Populated | * * * *  * |

  Failing   |            |

  Failed    |            |


[mp] MP:CM> ps


Display detailed status of the selected MP bus device.



The following MP bus devices were found:

+---+----+-----+-------+-------+-----------+

|   |    |     |       |       |           |

|   |    | Sys |       |  IO   | Bulk Pwr  |

|Cab| MP |Bkpln| Cells |Chassis| Supplies  |

| # |M  S|     |0 1 2 3| 0   1 |0 1 2 3 4 5|

+---+----+-----+-------+-------+-----------+

| 0 |*  *|  *  |* *    | *   * |* *     * *|

+---+----+-----+-------+-------+-----------+


You may display detailed power and hardware status for the following items:


    T - Cabinet

    S - System Backplane

    G - MP (Core I/O)

    P - IO Chassis

    C - Cell

        Select Device: c

    Enter cell number: 0


HW status for Cell 0 : NO FAILURE DETECTED


Power status : on, no fault

Boot is not blocked

PDH memory is shared

Processor Compatibility : OK

RIO cable status : connected

RIO cable connection physical location : PCI Domain 0

Core cell is cell 0

Attention Led is off


PDHC status Leds :  ***-


CPU Module Slot    0 1 2 3

Populated         P P P P

Local 48V Good    * * * *

Power Enabled     * * * *

Power Good        * * * *


   (* - True, P - Processor, T - Terminator)




DIMMs populated:

0 . . . 4 . . . 8 . . .12 . . .

*   *   *   *                  


                                  1 1 1 1 1 1

VRM's           1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

Present      : * * * * * * * * * * * * * * *

Enabled      : * * * * * * * * * * * * * * *

Pwr Good     : * * * * * * * * * * * * * * *



Front Side Bus Freq.    : 200 MHz

CPU Core Freq.          : 1000 MHz

CPU Part Number         : PA8800


System Boot Rom (SFW) firmware rev  24.004

PDH controller (PDHC) firmware rev 3.031, built THU NOV 09 21:37:37 2006

MICE revision is 1.0


[mp] MP:CM> ps


Display detailed status of the selected MP bus device.



The following MP bus devices were found:

+---+----+-----+-------+-------+-----------+

|   |    |     |       |       |           |

|   |    | Sys |       |  IO   | Bulk Pwr  |

|Cab| MP |Bkpln| Cells |Chassis| Supplies  |

| # |M  S|     |0 1 2 3| 0   1 |0 1 2 3 4 5|

+---+----+-----+-------+-------+-----------+

| 0 |*  *|  *  |* *    | *   * |* *     * *|

+---+----+-----+-------+-------+-----------+


You may display detailed power and hardware status for the following items:


    T - Cabinet

    S - System Backplane

    G - MP (Core I/O)

    P - IO Chassis

    C - Cell

        Select Device: c

    Enter cell number: 1


HW status for Cell 1 : FAILURE DETECTED


Power status : on, 1.2V Module 0, VRM #1 VOLTAGE FAULT

Boot is not blocked

PDH memory is shared

Processor Compatibility : OK

RIO cable status : connected

RIO cable connection physical location : PCI Domain 1

Core cell is cell 0

Attention Led is off


PDHC status Leds :  ****


CPU Module Slot    0 1 2 3

Populated         P P P P

Local 48V Good    * * * *

Power Enabled     * * * *

Power Good        * * * *


   (* - True, P - Processor, T - Terminator)




DIMMs populated:

0 . . . 4 . . . 8 . . .12 . . .

*   *   *   *                  


                                  1 1 1 1 1 1

VRM's           1 2 3 4 5 6 7 8 9 0 1 2 3 4 5

Present      : * * * * * * * * * * * * * * *

Enabled      : * * * * * * * * * * * * * * *

Pwr Good     :   *   * * * * * * * * * * * *



Front Side Bus Freq.    : 200 MHz

CPU Core Freq.          : 1000 MHz

CPU Part Number         : PA8800


System Boot Rom (SFW) firmware rev  24.004

PDH controller (PDHC) firmware rev 3.031, built THU NOV 09 21:37:37 2006

MICE revision is 1.0


[mp] MP:CM>
[END] 2014/2/7 15:43:20

yeahzp

Reporting Entity:  Processor Dependent Hardware Controller located in cabinet 0, slot 1
Physical Location:  Low voltage power supply cabinet 0 slot 1

如何确定这个slot1的位置 ？

server user guide里没有查到这个位置

congshuaiok

日志上写的很清楚啊，CELL 1上的1，3两个VRM坏了，换掉就OK了。

lgatuk

回复 6# congshuaiok


    HW status for Cell 1 : FAILURE DETECTED

Power status : on, 1.2V Module 0, VRM #1 VOLTAGE FAULT

我只看到了VRM #1  
没有看到3  请教~

yeahzp

我看到的也是，就一个vrm

lbseraph

回7#、8#，#3的VRM的power状态也不正常。

                                 1 1 1 1 1 1
VRM's           1 2 3 4 5 6 7 8 9 0 1 2 3 4 5
Present      : * * * * * * * * * * * * * * *
Enabled      : * * * * * * * * * * * * * * *
Pwr Good     :   *   * * * * * * * * * * * *

yeahzp

回复 9# lbseraph


    这个没看明白。

不是应该以mp>sl>sel里的为准嘛？