关于在“PearPC”上的问题

eyey1117

本人始终无法顺利安装“Mac OS X”。我今天重新弄“PearPC”一遍，它没有再显示“Still waiting for root device”了，却一直停留在开机的灰色画面，到后来，画面中的苹果图案没了，变成一个“禁止进入”的标志（－＿－），到底有何方法？
现附上屏幕截图数帧及“PearPC”的《Config File》。
截图一（选单）：

截图二（灰色画面）：

截图三（灰色画面；“禁止进入”标志）：

《Config File》：
## PearPC Configuration File

##
## Resolution
##
## 0: 640x480x15
## 1: 640x480x32
## 2: 800x600x15
## 3: 800x600x32
## 4: 1024x768x15
## 5: 1024x768x32
##
## default: 3

#ppc_start_resolution = 3

##
## Redraw interval (in ms)
## must be between 1 and 999
##
## If you set this higher, PearPC will spend less time doing redraws (and so run faster)
## but feel less responsive. You should adjust this to your computer speed and personal
## preference.
##
## Setting this to a value less than 10 is silly.
##

redraw_interval_msec = 50

##
## Loader
##

##
## Boot method
## this can be
## 1. "auto", prom will boot the first bootable partition found (default)
## 2. "select", prom will show you a list of bootable partitions
## 3. "force", prom will load and boot the local file prom_loadfile
##

prom_bootmethod = "select"

## Example of how to use "force":

#prom_bootmethod = "force"
#prom_loadfile = "test/yaboot"
#prom_env_bootpath = "disk"

##
## bootargs: don't change unless you know what you are doing
## machargs: set to "-v" to get a verbose startup
##

#prom_env_bootargs = ""
prom_env_machargs = ""

##
## This is needed if you want to boot Mac OS X
##
prom_driver_graphic = "video.x"

## This will adjust the position of the initial page table (don't change)

#page_table_pa = 104857600

##
## CPU Config
##
## Processor Version Register
## Defaults to 0x00088302
## Only change if you know want you are doing
##

#cpu_pvr = 0x00088302


##
## Main memory (default 128 MiB)
## must be >;= 64 MiB
##

memory_size=0x10000000


##
## IO Devices
##

##
## PCI IDE Config
##
## Drive type will be set according to file extension:
## .img: Harddisk (filesize must be multiple of 516096)
## .iso: CD-Rom
## Or you can override this by specifying the type via
## pci_ide0_master_type / pci_ide0_slave_type

pci_ide0_master_installed = 1
pci_ide0_master_image = "F:\MAC.iso"
pci_ide0_master_type = "cdrom"

pci_ide0_slave_installed = 1
pci_ide0_slave_image = "macosx_6gb.img"
pci_ide0_slave_type = "hd"

##
## Network
##
## Choose one of the cards

pci_3c90x_installed = 0
pci_3c90x_mac = "de:ad:ca:fe:12:34"

pci_rtl8139_installed = 0
pci_rtl8139_mac = "de:ad:ca:fe:12:35"

##
## USB
##
pci_usb_installed = 1

##
## NVRAM
##
nvram_file = "nvram"