免费注册 查看新帖 |

ChinaUnix.net

  平台 论坛 博客 文库
12下一页
最近访问板块 发新帖
查看: 11145 | 回复: 14

用make_recovery磁带恢复操作系统 [复制链接]

论坛徽章:
0
发表于 2005-08-03 21:00 |显示全部楼层
1.        Power up the server
3.        Upon seeing the following prompt in the console screen, press any key on the keyboard to interrupt the auto-boot process

….
To discontinue, press any key within 10 seconds.
….

4.        You should see the following prompt when the auto-boot process is interrupted

Main Menu: Enter command >;
5.        Insert the latest system backup tape.
6.        You can use command sea to search to bootable media. Note the device type “Sequential access media”, which indicates it is the bootable tape. Then boot from it.

Main Menu: Enter command >; sea

Searching for potential boot device(s)
This may take several minutes.

To discontinue search, press any key (termination may not be immediate)

Path#        Device Path (dec)        Device Path (mnem)        Device Type
-------------------------------------------------------------------
P0        0/0/1/0.3                extscsi.3                Sequential access media
P1        x/x/x/x.x                extscsi.2                Random access media
P2        x/x/x/x.x                intscsia.6                Random access media
……

9.   Type in the boot command:

Main Menu: Enter command >; boot p0  

10. The bootstrap of the tape will be loaded into memory until you see the following question

Interact with IPL (Y, N, or Cancel)? >;

11. Answer "N" to follow the automatic recovery of the Production Server

12. The following message will then be display. Press <Return>; key to acknowledge the message and continue the recovery process.

Press Return to continue:

13.  The following message will then be display. Press <Return>; key to acknowledge the message and continue the recovery process.

….
                [        Install HP-UX         ]
                [     Run a Recovery Shell        ]
                [      Advanced Options        ]
….

14.   Use the <Up>;, <Down>;, or <Tab>; keys to navigate and highlight the "Install HP-UX" option, and press <Return>; key to select the option. The system will then display the next screen. Use the <Tab>; key to navigate and <Space Bar>; key to select the following options. Once the options are selected, use <Tab>; key to navigate to [OK] and press <Return>; to acknowledge ok to proceed.

….
Source Location Options:
….
  • Media only installation
    ….
    User Interface Options:
    ….
  • Advanced Installation (recommended for disk and file system management)
    ….

    15.  The system will then start loading the user configuration interface program. The "/opt/ignite/bin/tool" menu is displayed. Under the "Basic" tab, Make sure the configuration entries of "[Root Disk …]" display the following:

    Configurations: [HP-UX System Recovery ->;] [Description …]
    Environments: [Recovery Archive ->;] (HP-UX B.11.00)
    [Root Disk …] SEAGATE_ST34573N
    File System: [HP-UX save_config layout ->;]
    [Root Swap (MB) …] 512 Physical Memory (RAM) = 256MB
    [Languages …] English   [Keyboards …]  [Additional …]

    ……
    [hostname…]
    [IP Address …]          Subnet Mask:            .
    [Set Time Zone …]      [Network Services…]
    [Set Root Password …]         [Additional Interfaces…]
    ……

    16.  Use <Tab>; key to navigate to "[Go !]", and press <Return>; key to proceed. Message prompt that disks  and  (or  and)  will be used as root disk. Warning also prompt that the 2 disks seem to have data on it.

    17.  Use <Tab>; key again to navigate to "[Go !]" and press <Return>; key again to confirm the restoration process.

    18. The server will continue the recover process and will be rebooted after successfully completed the restore.
  • 论坛徽章:
    0
    发表于 2005-08-03 22:24 |显示全部楼层

    用make_recovery磁带恢复操作系统

    好样的,鼓励一下,设精。

    论坛徽章:
    0
    发表于 2005-08-03 23:19 |显示全部楼层

    用make_recovery磁带恢复操作系统

    谢谢版主

    论坛徽章:
    0
    发表于 2005-08-04 09:38 |显示全部楼层

    用make_recovery磁带恢复操作系统

    只做了make_tape_recovery 的备份,没有做过恢复,非常有用。

    论坛徽章:
    0
    发表于 2005-08-04 09:39 |显示全部楼层

    用make_recovery磁带恢复操作系统

    ding!

    论坛徽章:
    0
    发表于 2005-08-04 09:48 |显示全部楼层

    用make_recovery磁带恢复操作系统

    好贴。。支持一把。

    论坛徽章:
    0
    发表于 2005-08-04 12:15 |显示全部楼层

    用make_recovery磁带恢复操作系统

    从培训资料上直接cp过来的吧,呵呵

    论坛徽章:
    0
    发表于 2005-08-04 12:23 |显示全部楼层

    用make_recovery磁带恢复操作系统

    不是的,是HP的工程师写的,我整理了一下,觉得很有用就分享给大家!

    论坛徽章:
    0
    发表于 2005-08-05 21:07 |显示全部楼层

    用make_recovery磁带恢复操作系统

    不明白,过多的修改造成无法进入98界面,无法关机,开机蓝屏也能用这恢复吗??

    论坛徽章:
    0
    发表于 2005-08-08 12:19 |显示全部楼层

    用make_recovery磁带恢复操作系统

    hao, ding
    您需要登录后才可以回帖 登录 | 注册

    本版积分规则 发表回复

    ITPUB技术栈

    ITPUB技术栈是ITPUB企业打造的垂直于IT领域的知识社群平台,在这里,你既可以是创作者也可以是消费者。如果你的IT生涯丰富多彩,喷薄的个人价值尽可在小栈内体现;如果你渴望找到志同道合的伙伴,拓宽人脉,小栈比跑会场更快。 小栈特色:
    1.极高的用户转化率,实现更直接的知识变现;
    2.随时随地,刷个朋友圈的时间,实现更长效的信息沉淀;
    3.戳痛、难点的专业咨询,更接近成功解决方案的时刻;
    4.贴近意见领袖,个人高速成长,迈入更富有价值的人际圈。

    ----------------------------------------

    技术小栈>>
      

    北京盛拓优讯信息技术有限公司. 版权所有 16024965号-6 北京市公安局海淀分局网监中心备案编号:11010802020122
    中国互联网协会会员  联系我们:huangweiwei@it168.com
    感谢所有关心和支持过ChinaUnix的朋友们 转载本站内容请注明原作者名及出处

    清除 Cookies - ChinaUnix - Archiver - WAP - TOP