棘手的出错信息,请高手来看看解决办法!!!!!!

可爱MM

|> messages:Jun 25 13:58:30 oasvr-groupapp lw8: [ID 702911 kern.warning] WARNING: lw8: system shutdown due to SC request.
messages:Jun 25 13:58:47 oasvr-groupapp lw8: [ID 197696 kern.error] Device voltage problem: /N0/RP2 abnormal state for device: Board 0 1.5 VDC 0 Value: 1.84 Volts DC
messages:Jun 25 13:58:47 oasvr-groupapp lw8: [ID 847255 kern.error] Device voltage problem: /N0/RP2 abnormal state for device: Board 0 3.3 VDC 0 Value: 4.0 Volts DC
messages:Jun 25 13:58:48 oasvr-groupapp lw8: [ID 116014 kern.warning] WARNING: /N0/RP2 temperature is approaching max limit of 87C
messages:Jun 25 13:58:48 oasvr-groupapp lw8: [ID 298388 kern.warning] /N0/RP2 Board 0 Temp. 0 value: 125 Degrees C
messages:Jun 25 13:58:48 oasvr-groupapp lw8: [ID 501304 kern.warning] Check for abnormal environmental operating conditions.
messages:Jun 25 13:58:48 oasvr-groupapp lw8: [ID 621400 kern.error] Device temperature problem at: /N0/RP2 . Shutting down due to Board 0 Temp. 0
Value: 125 Degrees C
messages:Jun 25 13:58:49 oasvr-groupapp lw8: [ID 331400 kern.error] Shutdown requested due to temperature problem
messages:Jun 25 13:58:49 oasvr-groupapp lw8: [ID 215604 kern.crit] FULL-COOLING ENGAGED: turning fans high
messages:Jun 25 13:58:49 oasvr-groupapp lw8: [ID 883730 kern.notice] /N0/RP2, sensor status, outside acceptable limits (7,1,0x3010c0d00050000)
messages:Jun 25 13:58:49 oasvr-groupapp lw8: [ID 883986 kern.notice] /N0/RP2, sensor status, outside acceptable limits (7,1,0x3010c0d00070000)
messages:Jun 25 13:58:50 oasvr-groupapp lw8: [ID 883474 kern.notice] /N0/RP2, sensor status, outside acceptable limits (7,1,0x3010c0d00030000)
messages:Jun 25 13:58:50 oasvr-groupapp lw8: [ID 244980 kern.warning] WARNING: /N0/RP2 temperature is approaching max limit of 63C
messages:Jun 25 13:58:50 oasvr-groupapp lw8: [ID 587167 kern.warning] /N0/RP2 Board 0 Temp. 1 value: 125 Degrees C
messages:Jun 25 13:58:51 oasvr-groupapp lw8: [ID 501304 kern.warning] Check for abnormal environmental operating conditions.
messages:Jun 25 13:58:51 oasvr-groupapp lw8: [ID 910179 kern.error] Device temperature problem at: /N0/RP2 . Shutting down due to Board 0 Temp. 1
Value: 125 Degrees C
messages:Jun 25 13:58:51 oasvr-groupapp lw8: [ID 912438 kern.error] A shutdown is already in progress
messages:Jun 25 13:58:51 oasvr-groupapp lw8: [ID 908064 kern.notice] /N0/FT0, fan speed, High (4,2)
messages:Jun 25 13:58:51 oasvr-groupapp lw8: [ID 114565 kern.notice] /N0/RP2, sensor status, outside acceptable limits (7,1,0x3010c0d00030100)
messages:Jun 25 14:00:58 oasvr-groupapp lw8: [ID 945825 kern.notice] /N0/FT0, fan speed, Low (4,1)

可爱MM

期待高手!!!!!!!!!!

susbin

好象你的系统过热。机房温度如何？ 机器周围是否通风？
您提供的系统信息太少了。

阿毛~

温度太高了吧，

westwest

温度过高
有可能要换风扇

miaohuil

环境温度太高？
如果不是，我个人认为可以隔离和POWEROFF RP2试试

可爱MM

可以隔离和POWEROFF RP2试试 ? 请问具体如何做呀,好象要LOM SC里也要看和检查,有这文档资料么,万分感谢

xuefm

原帖由 可爱MM 于 2006-6-27 18:40 发表
|> messages:Jun 25 13:58:30 oasvr-groupapp lw8: [ID 702911 kern.warning] WARNING: lw8: system shutdown due to SC request.
messages:Jun 25 13:58:47 oasvr-groupapp lw8: [ID 197696 kern.error] Dev ...

个人认为温度引起的，看一下机器风扇，机房温度。

youngvv

Check for abnormal environmental operating conditions.

可爱MM

RP2是必须POWEROFF 机器才能做,不是FRU