[求助]U5如加一块S3 VIRGE/DX的PCI显卡，直接加电能从该显卡输出到显示器上吗？

roman_pan

我有台270的U的SUN U5。
现集成显卡有问题，没信号输出。能否加一块S3 VIRGE/DX的PCI显卡，从该显卡输出？

该显卡的具体参数：
WINFAST（丽台）的，
主芯片：S3 VIRGE/DX，是PCI的

在加电后可以直接从该显卡输出到显示器吗？

Philmoon

要加SUN专用的显卡PGX8、PGX32、PGX64等。PC上的恐怕不行。

roman_pan

我查了一下HCL，也就是兼容列表
这张显卡是兼容的

roman_pan

各位大虾们还有什么建议给我？

nus

原帖由 roman_pan 于 2006-10-11 22:08 发表
我查了一下HCL，也就是兼容列表
这张显卡是兼容的

u5是sparc的, 你查的HCL，也就是兼容列表是针对x86

差别大了， 应该是不兼容的。

想用Xwindows, 通过Xmanager网络联过去不是更灵活方便？
网络就是计算机的含义，包括你想要的图形，也是可以通过网络去获取的

roman_pan

怎么办啊

tianqing

Installing a PGX[TM] Frame Buffer in a Ultra[TM] 5 or Ultra[TM] 10

--------------------------------------------------------------------------------

Document Body
When installing a PGX Frame Buffer (PN 370-2256) in an Ultra 5 or Ultra 10
you will need to follow these steps to have it to work properly.

1. Turn the power off and install the PGX Frame Buffer into a PCI slot on
   the PCI riser card.
   
   **** Remember to use proper static protection when installing ****
   **** boards or devices in the system.                         ****

2. Turn the power back on. Once the video comes back hold down the stop key
   and the letter A key and the same time. This will stop the system from
   booting and allow you to issue the commands needed for the PGX Frame
   Buffer to work properly. At the OK prompt issue the show-devs command.
   This shows the devices in the system and their respective paths. You
   will need to look for a line that looks like the example below.

   Example:

     OK show-devs


     /pci@1f,0/pci@1/SUNW,m64B@1
                               /\
                               ||
                      PCI SLOT (1,2,3,4)

   The last number will depend on what slot you installed the PGX
   Frame Buffer into on the PCI riser card.

3. You will now need to create an nvalias for the PGX Frame Buffer
   using the nvalias command. Example shown below.

   Example:

     OK nvalias screen1 /pci@1f,0/pci@1/SUNW,m64B@1
                ------- ---------------------------  
                  /\               /\
                  ||               ||
                  ||     (path from show-dev command)
                  ||
      (screen1 is used for example only)
      
      The name of the nvalias can be any name you want is to be.
      
      *****Caution, be careful not to duplicate a name already used.******
      
      You can see what has been used by using the devalias command at the
      OK prompt. This will display the aliases already in use.

      After creating the nvalias. Issue the devalias command at the OK prompt
      to verify that the nvalias you just created is present and has the
      correct path.

4.  Now that the nvalias has been created, you will now need to set the
    output-device to look at the new nvalias instead of the default setting.
    The default nvalias is screen, which points to the onboard video.
    You do this by using the setenv command. Example shown below.

    Example:

      OK setenv output-device screen1
     
    The system will echo what you set the environment variable to.

      output-device =       screen1

5.  You are now all set to issue the reset command at the OK prompt.
   
    OK reset
   
    While the system is rebooting, change the monitor from the onboard video
    to the PGX Frame Buffer. When the system initializes the video, it will
    initialize the PGX Frame Buffer and not the onboard video. If the OS is
    already installed, will need to do a stop A after the video initializes
    and issue the boot -r command to add the drivers for the PGX Frame Buffer.
    This is not an issue if you are doing a new install of the OS on the
    system. During installation, it will install the drivers necessary for
    the devices in the system.