The statements inside your source files are generally executed from top to bottom, in the order that they appear. control flow statements, however, break up the flow of execution by employing decision making, looping, and branching, enabling your program to conditionally execute particular blocks of code. This section describes the decision-making statements (if-then, if-then-else, switch...
by jim153 - Java文档中心 - 2007-06-18 16:30:03 阅读(1009) 回复(0)
有的时候,需要根据交换机的设置情况,手工网卡驱动的flow control参数,链接中的文章给出了一个这种情况下的设置实例。 参见: http://www-307.ibm.com/pc/support/site.wss/document.do?lndocid=MIGR-57465 4-port Gigabit Ethernet Switch Module requires Blade flow control activation - IBM eServer BladeCenter ...
Master:Release 10.2.0.3.0 Propagation Schedule for (STRMADMIN.STREAMS_CAPTURE_Q, GYDB10.RECOVER) encountered following error: ORA-25307: Enqueue rate too high, flow control enabled Slave:Release 11.1.0.6.0 Thu Jun 11 03:04:46 2009 Errors in file /u01/app/oracle/diag/rdbms/gydb10/gydb10/trace/gydb10_as02_4603.trc (incident=9954): ORA-00600: internal error code, arguments: [kgqmdeq788], [], [],...
HP RP8400 双机热备份,运行SAP,数据库ORACLE。今天突然TELNET,FTP, CONSOLE LOGIN都不能进入系统,网络正常,SAP GUI能够进入SAP系统,TELNET 时出现信息: “Escape character is '^]'. Local flow control off Connection closed by foreign host.” 这是什么问题,如何解决,请各位老大帮忙,谢谢。
Initialization flow of control The bootloader is the low-level component resident in system nonvolatile memory (Flash or ROM) that takes control immediately after the power has been applied. It is typically a small, simple set of routines designed primarily to do low-level initialization, boot image loading, and system diagnostics. It might contain memory dump and fill routines for exam...
HP RP8400 双机热备份,运行SAP,数据库ORACLE。今天突然TELNET,FTP, CONSOLE LOGIN都不能进入系统,网络正常,SAP GUI能够进入SAP系统,TELNET 时出现信息: “Escape character is \'^]\'. Local flow control off Connection closed by foreign host.” 这是什么问题,如何解决,请各位老大帮忙,谢谢。
1:如果达到HIGH_WM,接收设备会发送pause帧,发送设备接收到pause帧后会暂停发送数据 2:如果到达LOW_WM,接收设备会发送pause帧,让发送设备继续发送数据 那么在这个期间,pause帧会一直在发送么? 我的环境上还是在不停的发送pause帧 0000 01 80 c2 00 00 01 00 00 00 00 00 07 88 08 00 01 ........ ........ 0010 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ........ ........ 0020 00 00 00 00 00 00 00 00...
请教一下, 如果UART硬件支持 (uart controller and cable),并工作在hardware flow control状态下, 另一端串口的terminal 属性设成none flow control, 能和硬件进行通讯吗? rs232协议是否允许这种情况? 换一种说法: 是否允许UART通讯的两端,一端为hardware flow control, 另一端为none? [ 本帖最后由 yidou 于 2009-1-22 14:28 编辑 ]
请教一下, 如果UART硬件支持,并工作在hardware flow control状态下, 串口的terminal 属性设成noe flow control, 能和硬件进行通讯吗?
TCP-Friendly Unicast Rate-Based flow controlJamshid Mahdavi & Sally Floyd January, 1997 I. IntroductionThis document describes a technique for implementing TCP-friendly flow control for unicast applications which do not utilize TCP at the transport layer. Novice programmers might wish to avoid considering the effects their applications can have on the network and on other applications in the netw...