[email=root@host%]root@host%[/email] 根用户的shell提示符 [email=user@host]user@host[/email]> 运行模式CLI提示符 [email=user@host]user@host[/email]# 配置模式提示符 configure进入配置模式 lci 进入CLI 补全 空格 ? 查询命令 show interface terse 查看接口 show interface terse | except fe- 查看除fe-的接口 show interface terse | match se-3 只查看se-3接口 show interface | last 显示上一屏数据 show interfa...
[email=root@host%]root@host%[/email] 根用户的shell提示符 [email=user@host]user@host[/email]> 运行模式CLI提示符 [email=user@host]user@host[/email]# 配置模式提示符 configure进入配置模式 lci 进入CLI 补全 空格 ? 查询命令 show interface terse 查看接口 show interface terse | except fe- 查看除fe-的接口 show interface terse | match se-3 只查看se-3接口 show interface | last 显示上一屏数据 show interfa...
[email=root@host%]root@host%[/email] 根用户的shell提示符 [email=user@host]user@host[/email]> 运行模式CLI提示符 [email=user@host]user@host[/email]# 配置模式提示符 configure进入配置模式 lci 进入CLI 补全 空格 ? 查询命令 show interface terse 查看接口 show interface terse | except fe- 查看除fe-的接口 show interface terse | match se-3 只查看se-3接口 show interface | last 显示上一屏数据 show interfa...
[email=root@host%]root@host%[/email] 根用户的shell提示符 [email=user@host]user@host[/email]> 运行模式CLI提示符 [email=user@host]user@host[/email]# 配置模式提示符 configure进入配置模式 lci 进入CLI 补全 空格 ? 查询命令 show interface terse 查看接口 show interface terse | except fe- 查看除fe-的接口 show interface terse | match se-3 只查看se-3接口 show interface | last 显示上一屏数据 show interfa...
junos学习笔记(原创) [email=root@host%]root@host%[/email] 根用户的shell提示符 [email=user@host]user@host[/email]> 运行模式CLI提示符 [email=user@host]user@host[/email]# 配置模式提示符 configure进入配置模式 lci 进入CLI 补全 空格 ? 查询命令 show interface terse 查看接口 show interface terse | except fe- 查看除fe-的接口 show interface terse | match se-3 只查看se-3接口 show interface | last 显示上...
到现在为止,junos都还没有实现物理网卡,也一直不能够与主机系统通讯。我们给它添加千兆网卡。 编辑虚拟机所在目录的FreeBSD.vmx ,在 ethernet0.present = "TRUE" 后面添加: ethernet0.virtualDev = "e1000" 然后启动虚拟机,配上IP地址,查看一下: 已经正常启动了,并且能够和主机正常通讯 (192.168.1.233为主机的IP地址): 下面我们为junos多添加上几块网卡,这样我们就可以搭建出来计较复杂的实验拓扑了,满足试验要求...
下面我们启动虚拟机,然后用我们之前设定的root密码登陆 进入系统,好了,至此我们就完成了Freebsd4.11的安装。 下面开始junos的安装: 用ftp 将jinstall-7.3R2.9-domestic-signed.tgz上传到/var/tmp目录下 进行如下设置: # rm /dev/wd0c # ln -s /dev/ad0c /dev/wd0c # mkdir /var/etc # touch /var/etc/master.passwd # touch /var/etc/inetd.conf # touch /var/etc/group 如下所示 然后安装junos7.4,如果出现如下界面...
下面启动虚拟机,开始FreeBSD4.11的安装: 出现如下界面时,回车即可,意思是不要配置内核,保持默认。 选择安装模式,我们选择“Express”模式,表示一个快速安装 回车即可,进入如下界面,这是让我们选择freebsd的硬盘使用,这里直接按“A”键,表示将全部的空间划分给freebsd使用 然后按“Q”键进入如下界面,在这里设置引导程序安装方式,我们选择第二项“Standard” 然后回车 下面进行磁盘分区: 按“C”创建一个新...
本文为个人学习Juniper过程中所写,自己走了一些弯路,写出来与大家共享。如果转载,请大家保留作者信息,谢谢。 2008年9月2日开始研究Freebsd 与 junos的安装,到今天(2008-9-6)算是完整而且成功地实现。在这几天中,走了一些弯路,自己整日漫游于Internet,并且得到了一些朋友的帮助,特别要感谢鬼才兄,是他为我提供了jinstall-8.5R1.14-domestic-signed.tgz,才使我的实验得以继续下去。开始,鬼才兄用QQ的离线传输...
[email=root@host%]root@host%[/email] 根用户的shell提示符 [email=user@host]user@host[/email]> 运行模式CLI提示符 [email=user@host]user@host[/email]# 配置模式提示符 configure进入配置模式 lci 进入CLI 补全 空格 ? 查询命令 show interface terse 查看接口 show interface terse | except fe- 查看除fe-的接口 show interface terse | match se-3 只查看se-3接口 show interface | last 显示上一屏数据 show interfa...