1. 简介 BEA的WEBLOGIC提供在互联网上进行WEB服务所需要的强大的电子商务平台。作为行业领先的J2EE应用服务器,对于所有在weblogic平台上进行的应用部署,其主旨必然是要如何提供给用户一个更稳定可靠的、可伸缩的、快速的服务应用。 2. BEA Weblogic服务器和负载均衡器 由于网上用户访问量的急剧增长,信息获取的速度和稳定度成了制约互联网发展的主要因素。服务器必须具备提供大容量并发访问服务的能力,光靠单机版的服...
To install your Certificate and Intermediate CA Certificate, follow these instructions: a. Fetch your certificate and the Intermediate CA certificate: 1. You will receive an email when your certificate is issued. 2. Copy and Paste your certificate (first certificate) to Notepad and save as a cert.cer 3. Copy and Paste the Intermediate CA Certificate (second certificate) to Notepad and save as...
我们公司买了SUN V440服务器 现在给0网卡配置了ip地址 我想在1的网卡上在配置一个ip应该如何去配置 因为我看到hosts里面有0的ip,netmasks里面有他的掩码 default里面有网关 不知道 第二个网卡ip往哪里配置,请高人指教?
该方案如下:f5上配置有DNS服务的公网ip地址10.1.1.22(假设),f5下挂4台DNS服务器,一个master/三个slave。 应用场景:公网宽带用户可以使用DNS的ip地址10.1.1.22正常解析网络上的服务器 问题:当在后台重启DNS服务之后,公网用户仍可以ping通DNS的地址,但用nslookup无法解析域名 请各位遇到过该问题的大侠指点一下,是否是重启之后f5和DNS服务器之间通信有问题呢?
可以修改以下文件: /etc/hostname.interface /etc/hosts /etc/hostname.xxx /etc/defaultrouter(默认网关) /etc/netmasks(掩码) /etc/inet/ipnodes 然后重新启动系统,或者用ifconfig 来添加临时的ip地址.用route add default xxx.xxx.xxx.xxx来添加临时的默认网关,用这些命令更改的设置,在系统重启后就不会保存的。 注意修改ip,主机名的涉及的文件: 1. /etc/hostname.interface Interface是网卡的型号,有le、hme等。L...
摘自: http://xnming.blogbus.com/logs/16561419.html ##### # 手工指定的方式 ################################ # ipconfig fxp0 192.168.8.33/24 # 添加网卡ip # route add default 192.168.8.1 # 添加路由(也可理解为网关) 立即生效,但是重启后失效。 如何重启后仍然保持呢? # ee /etc/rc.conf ifconfig_fxp0="inet 192.168.8.8 netmask 255.255.255.0 " # fxp0 网卡地址和子网掩码 defaultrouter="192.168.8....
FreeBSD ip 配置总结 代码:##### # 手工指定的方式 ################################ # ipconfig fxp0 192.168.8.33/24 # 添加网卡ip # route add default 192.168.8.1 # 添加路由(也可理解为网关)立即生效,但是重启后失效。 如何重启后仍然保持呢? 代码:# ee /etc/rc.conf ifconfig_fxp0="inet 192.168.8.8 netmask 255.255.255.0 " # fxp0 网卡地址和子网掩码 defaultrouter="192.168.8.10" # 网关地址 hostn...
本人初学freebsd,不知设置ip配置 re.conf defaultrouter="192.168.1.1" hostname="gh.com" ifconfig_s10="inet 192.168.1.200 netmask 255.255.255.0" sshd_enable="YES" usbd_enable="YES" resolv.conf domain gh.com nameserver 202.96.128.166 nameserver 202.96.128.86 上面这样设置了,为什么不行呀