今天突然想到Solaris 下的usb 转 串口。 搜了一下,有结果了在附件里。 solaris 是支持usb-serial的。 ATEN Technology, Inc. Inside Out Networks, Inc. Keyspan 三个公司的usb转串口 但是平常大家用的力特的(z-tek)的没有在名单里。 那位兄弟能测试一下。 z-tek usb serial 1.0 z-tek usb-serial 2.0
by huanglao2002 - Solaris - 2006-12-12 20:47:50 阅读(1394) 回复(2)
The following instructions explain how to update the device driver configuration file on the Sun host to enable access to target and LUN pairs that are configured on a DS8000. Perform the following steps to update the Solaris driver configuration file: Note: Do not change or remove entries in kernel /drv/sd.conf for preexisting devices. Doing so can cause your system to become inoperable.Do not a...
Composite usb devices expose multiple functions to a host by using multiple interfaces. A compound device is an external hub that is combined with other devices. Compound devices appear to the host as a hub with one or more non-removable devices that are connected to the hub’s ports. 对于compound device,它内置的hub和其它设备都会有各自的device address, 而compoiste device只有一个device address。实...
各位好, 我的系统使rh as3 update2 但是usb的u盘不能用。 看网上说加载sd_mod的module。 我用insmod sd_mod modprobe sd_mod lsmod 能看到那个模块,但是是unused。 所以我的u盘还是不能用, 请问有没有什么解决办法? 另外,我的debian3.0 r2能找到sd_mod.o 但是insmod不让加载,请问是什么原因? 多谢。
平台:sharp lh7a404 、kernel 2.6.12 外扩usb host: cypress sl811hst, 插上U盘后,出现如下信息: / # usb 2-1: new full speed usb device using sl811-hcd and address 2 usb 2-1: device descriptor read/64, error -110 usb 2-1: device descriptor read/64, error -110 usb 2-1: new full speed usb device using sl811-hcd and address 3 usb 2-1: device descriptor read/64, error -110 usb 2-1: device descriptor rea...
usb的使用似乎成了老大难问题,其实solaris 10中对usb设备的支持已经very good了,默认状况下即插即用。以下是本人的一些心得,请参考使用。 usb设备使用简介 版权声明:原创cu-yuhuohu,任何网站未经授权拒绝转载 内容简介: usb设备状态检测 vold在运行时使用U盘 vold未运行时使用U盘 vmware如何使用U盘 故障诊断 哥们,看帖要推荐啊,点这里 1、check the usb-device QUOTE: 查看usb存储设备是否已插入,在启动消息中应...
我用的是usb主机芯片isp1161 , 驱动程序是在网上找的!!! 在bootloader 中 测试硬件 , 可以读出 isp1161 的 ID 号, 和 读写 HcScratch 寄存器. 但是,当linux系统启动之后, 在isp1161 的 hcd 中 怎么也读不到 ID . isp1161 的片选线 是 CS4 , 采用 PIO 模式 与 pxa255 接口. MSC2 = 0x7ff8fff9 ; 主机数据口物理地址 : 10000000 主机命令口地址: 10000002 通过 ioremap_nocache () 函数 将物理地址映射到虚拟地址. 是读写时序...
最近搞了一个blade 100工作站学习用,插入usb键盘启动的时候,屏幕提示“ERROR: usb time out cannot open input device”,然后输入输出设备就转向串口了。 请高手指点一下,如何定位这是usb接口的问题,还是键盘的问题(4个usb接口都如此)? 串口也不能用,IP地址也不知道,实在不知道还能怎么登录系统,郁闷! 我已经在CU论坛和GOOGLE上都搜索过了,没有找到有用的资源,请高手指点一下,非常谢谢! [ 本帖最后由 zhyl120 ...