Openswan IPSec is an open source implementation of IPSec that is included in many Linux distributions. When appropriately configured, it can interoperate with fortigate VPNs. Global settings The global settings for the Openswan IPSec service are found in /etc/ipsec.conf. Unless you are certain that you don't need NAT traversal, ensure that the following line appears in ipsec.conf: nat_travers...
Configure the fortigate unit Configure the Phase1 and Phase 2 VPN settings To configure the Phase1 settings Go to VPN > IPSec > Phase 1. Select Create New and enter the following: Gateway Name: SonicWall Remote Gateway: Static IP IP Address: ip address Mode: Main Authentication Method: Preshared Key Pre-shared Key: preshared key Select Advanced and enter the following: Encryption: 3DES Authentic...
Case Scenario You have to two groups of users attempting to access the Internet through the fortigate. Most users need to be restricted in their access to the Internet. A few select users are permitted unrestricted access to the Internet. General Question How can the fortigate distinguish between the two sets of users? The solution is to enforce firewall authentication against two distin...
目 录 1、fortigate500的基本配置步骤 4 1.1防火墙加电,进入web配置 4 1.2区域的配置 4 1.3配置外口默认网关 5 1.4配置路由 5 1.5配置虚拟外网IP 6 1.6配置动态池 6 1.7配置策略地址组 7 1.8配置端口服务 7 1.9组合服务 8 1.10将组合服务关联到映射IP 9 1.11完成其它需求 10 2、配置中需要特别注意的几个问题: 11 fortigate500防火墙配置指导 fortigate500防火墙是美国飞塔公司的一款高性能防火...
fortigate配置使用policy route 环境 CN分支使用fortigate 200A作为防火墙,一条出口线路; VN分支使用fortigate 100A,两条出口线路; US分支使用linksys,一条出口线路。 现在要把三地分别用vpn连接起来,问题主要在VN的双WAN上 起先WAN1使用XDSL modem动态拨号,WAN2是静态ip,直接通过fortigate pppoe获得ip vpn走wan2,其他走wan1 1 VNCN CN ip:222.222.66.2(假设ip) 内网ip:192.168.0.0/20 1.1 首先需要在VPN-...
You can use secure copy (SCP) protocol to download the configuration file from fortigate units running FortiOS 3.0 MR3 or later. This article describes how to enable SCP download on the fortigate unit and use typical SCP client programs. Enable SCP Go to System > Admin > Settings. Select Enable SCP. Select Apply. Enable SSH access on the interface SCP uses SSH protocol to provide secure file tr...
There are different BIOS versions, depending on the fortigate model and its distribution date. These BIOSes may support different firmware installation options, and/or other features. Currently, depending on the BIOS version, there are three slightly different firmware loading features: No BIOS menu, and Y/N prompt to save firmware. No BIOS menu, and D/R (save a Default OR Run image without sav...
Unless you are doing this to resolve an outage, plan this firmware installation because there will be an outage from when you reboot the fortigate unit until it restarts with the new firmware. Configure the terminal client communication parameters to 8 bits, no parity, 1 stop bit (8-n-1), 9600 baud. (For fortigate-300 use 115,000 baud.) To load firmware Connect the terminal to the fortigate unit ...
fortigate units by default do not accept TCP or UDP connections on any port (except TCP port 443 HTTPS connections on the default internal interface for administration). This reduces the possibility of attacks such as Denial of Service (DoS) as the unit's ports cannot be discovered by probing. An exception to this "stealth" configuration is TCP port 113 (Ident/Auth). By default, this port returns...
cisco 3745 router config: Router#sh run Building configuration... Current configuration : 3002 bytes ! version 12.4 service timestamps debug datetime msec service timestamps log datetime msec no service password-encryption ! hostname Router ! boot-start-marker boot-end-marker ! enable secret 5 $1$SrWM$w.qmxnXALIyR0gTRGm3Gc1 ! no aaa new-model ! resource policy ! ip subnet-zero ip cef ! ! no ip ...
There are different BIOS versions, depending on the fortigate model and its distribution date. These BIOSes may support different firmware installation options, and/or other features. Currently, depending on the BIOS version, there are three slightly different firmware loading features: No BIOS menu, and Y/N prompt to save firmware. No BIOS menu, and D/R (save a Default OR Run image without sav...