N1290,solaris10,如何删除与添加一块板子?
本帖最后由 coologin 于 2013-02-18 11:05 编辑管理员指南是通过DR操作规程,使用cfgadm
是否这是样,但指南上没有给出具体操作实例。那位兄弟能否补充一下删除与添加一块板子的操作流程。
另,如果二块板子的FW固件不致,是否影响在SOLARIS下加载失败 要在SC下对板子的FW做同步～ 谢谢东方兄弟提醒，刚才查了一下手册，可以使用
此步骤会将 CPU/内存板、IB6 和系统控制器升级到相同的固件级别
flashupdate [-y|-n] -c source-board destination-board
-c 将某块板指定为闪存映像的源。使用此选项可更新供替换的 CPU/内存板
-y 不提示进行确认。
-n 在要求确认时不执行此命令。
在执行 flashupdate 之前，请使用 showboards -p version 命令检查所有
板的固件版本。
在更新 CPU/内存板或 I/O 部件之前，请确保使用 poweron all 命令打开所有要
更新的板的电源。
Netra 1290 服务器系统管理指南 - Oracle Documentation
http://docs.oracle.com/cd/E19102-01/n1290.srvr/819.../819-6909-10.pdf
回复 2# 东方蜘蛛
本帖最后由 coologin 于 2013-02-20 10:12 编辑
lom>showb -pv
Component Compatible Version
--------- ---------- -------
SSC1 Reference5.20.17 Build_01
/N0/IB6 Yes 5.20.17 Build_01
/N0/SB0 Yes 5.20.17 Build_01
/N0/SB2 Yes 5.20.16 Build_01
lom>flashupdate -c SB0 SB2
Waiting for critical processes to finish.This may take a while.
Critical processes have finished.
Updating the flash image of PROM /N0/SB2/FP0 with PROM /N0/SB0/FP0
Erasing .................. Done
Programming .................. Done
Verifying .................. Done
Updating the flash image of PROM /N0/SB2/FP1 with PROM /N0/SB0/FP0
Erasing .................. Done
Programming .................. Done
Verifying .................. Done
lom>showb -pv
Component Compatible Version
--------- ---------- -------
SSC1 Reference5.20.17 Build_01
/N0/IB6 Yes 5.20.17 Build_01
/N0/SB0 Yes 5.20.17 Build_01
/N0/SB2 Yes 5.20.17 Build_01
断电，再开机。
发现在OS下看不到sb2,后来换sb2到sb4，在OS下也没发现。
难道是底板有问题？？ 报错如下：
lom>showlogs
Tue Feb 05 20:29:16 hlrdbsrv1 lom: Boot: ScApp 5.20.17, RTOS 49
Tue Feb 05 20:29:18 hlrdbsrv1 lom: SBBC Reset Reason(s): Power On Reset
Tue Feb 05 20:29:18 hlrdbsrv1 lom: Initializing the SC SRAM
Tue Feb 05 20:29:24 hlrdbsrv1 lom: Caching ID information
Tue Feb 05 20:29:26 hlrdbsrv1 lom: Clock Source: 75MHz
Tue Feb 05 20:29:30 hlrdbsrv1 lom: /N0/PS0: Status is OK
Tue Feb 05 20:29:30 hlrdbsrv1 lom: /N0/PS1: Status is OK
Tue Feb 05 20:29:31 hlrdbsrv1 lom: /N0/PS2: Status is OK
Tue Feb 05 20:29:32 hlrdbsrv1 lom: /N0/PS3: Status is OK
Tue Feb 05 20:29:32 hlrdbsrv1 lom: Chassis is in single partition mode.
Tue Feb 05 20:29:35 hlrdbsrv1 lom: NOTICE: /N0/FT0 is powered off
Tue Feb 05 20:29:36 hlrdbsrv1 lom: Cold boot detected: recovering active domains
Tue Feb 05 20:29:37 hlrdbsrv1 lom: Starting telnet server ...
Tue Feb 05 20:30:02 hlrdbsrv1 lom: SysEvent 5 /N0/PS0, power state, On (5,1)
Tue Feb 05 20:30:02 hlrdbsrv1 lom: /N0/SB0, hotplug status, SB0, module inserted (9,17)
Tue Feb 05 20:30:02 hlrdbsrv1 lom: /N0/SB2, hotplug status, SB2, module inserted (9,17)
Tue Feb 05 20:30:04 hlrdbsrv1 lom: /N0/IB6, hotplug status, IB6, module inserted (9,17)
Tue Feb 05 20:30:04 hlrdbsrv1 lom: /N0/RP0, hotplug status, RP0, module inserted (9,17)
Tue Feb 05 20:30:04 hlrdbsrv1 lom: /N0/RP2, hotplug status, RP2, module inserted (9,17)
Tue Feb 05 20:30:04 hlrdbsrv1 lom: SysEvent 5 /N0/PS1, power state, On (5,1)
Tue Feb 05 20:30:05 hlrdbsrv1 lom: SysEvent 5 /N0/PS2, power state, On (5,1)
Tue Feb 05 20:30:06 hlrdbsrv1 lom: SysEvent 5 /N0/PS3, power state, On (5,1)
Tue Feb 05 20:30:21 hlrdbsrv1 lom: /N0/FT0, fan speed, Low (4,1)
Tue Feb 05 20:30:31 hlrdbsrv1 lom: /N0/FT0, fan speed, Low (4,1)
Tue Feb 05 20:32:58 hlrdbsrv1 lom: Domain Shell - A: poweron: Initiating keyswitch: on, domain A.
Tue Feb 05 20:32:58 hlrdbsrv1 lom: Domain Shell - A: poweron: Initiating keyswitch: on, domain A.
Tue Feb 05 20:39:10 hlrdbsrv1 lom: /N0/SB2 : Failed AR interconnect test. Status = 0e000fff
Tue Feb 05 20:39:10 hlrdbsrv1 lom: AR Interconnect test: System board SB2/ar0 address repeater connections to system board RP0/ar0 failed
Tue Feb 05 20:39:16 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_CMD_VLD
Tue Feb 05 20:39:17 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_BIDIPAR
Tue Feb 05 20:39:17 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:17 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:17 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:17 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:17 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:17 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:17 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:21 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:21 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:21 hlrdbsrv1 lom: AR Interconnect test: System board SB2/ar0 address repeater connections to system board RP0/ar0 failed
Tue Feb 05 20:39:21 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_INCOMING
Tue Feb 05 20:39:21 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_PREREQ
Tue Feb 05 20:39:21 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:21 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:21 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:21 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:21 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:21 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:22 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:22 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:22 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:22 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:22 hlrdbsrv1 lom: AR Interconnect test: System board SB2/ar0 address repeater connections to system board RP0/ar0 failed
Tue Feb 05 20:39:22 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:22 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:22 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:22 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:22 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:22 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:22 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:23 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:23 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:23 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:23 hlrdbsrv1 lom: SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 20:39:23 hlrdbsrv1 lom: CPU Board V3 at /N0/SB2 has been removed from domain A due to a failure in interconnection test. Service action required.
lom>showcom
Component Status PendingPOST Description
--------- ------ ----------- -----------
/N0/SB0/P0 enabled- pass UltraSPARC-IV+, 1500MHz, 32M ECache
/N0/SB0/P1 enabled- pass UltraSPARC-IV+, 1500MHz, 32M ECache
/N0/SB0/P2 enabled- pass UltraSPARC-IV+, 1500MHz, 32M ECache
/N0/SB0/P3 enabled- pass UltraSPARC-IV+, 1500MHz, 32M ECache
/N0/SB0/P0/B0/L0 enabled- pass 1024M DRAM
/N0/SB0/P0/B0/L2 enabled- pass 1024M DRAM
/N0/SB0/P0/B1/L1 enabled- pass 1024M DRAM
/N0/SB0/P0/B1/L3 enabled- pass 1024M DRAM
/N0/SB0/P1/B0/L0 enabled- pass 1024M DRAM
/N0/SB0/P1/B0/L2 enabled- pass 1024M DRAM
/N0/SB0/P1/B1/L1 enabled- pass 1024M DRAM
/N0/SB0/P1/B1/L3 enabled- pass 1024M DRAM
/N0/SB0/P2/B0/L0 enabled- pass 1024M DRAM
/N0/SB0/P2/B0/L2 enabled- pass 1024M DRAM
/N0/SB0/P2/B1/L1 enabled- pass 1024M DRAM
/N0/SB0/P2/B1/L3 enabled- pass 1024M DRAM
/N0/SB0/P3/B0/L0 enabled- pass 1024M DRAM
/N0/SB0/P3/B0/L2 enabled- pass 1024M DRAM
/N0/SB0/P3/B1/L1 enabled- pass 1024M DRAM
/N0/SB0/P3/B1/L3 enabled- pass 1024M DRAM
/N0/SB2/P0 enabled- pass UltraSPARC-IV+, 1500MHz, 32M ECache
/N0/SB2/P1 enabled- pass UltraSPARC-IV+, 1500MHz, 32M ECache
/N0/SB2/P2 enabled- pass UltraSPARC-IV+, 1500MHz, 32M ECache
/N0/SB2/P3 enabled- pass UltraSPARC-IV+, 1500MHz, 32M ECache
/N0/SB2/P0/B0/L0 enabled- pass 1024M DRAM
/N0/SB2/P0/B0/L2 enabled- pass 1024M DRAM
/N0/SB2/P0/B1/L1 enabled- pass 1024M DRAM
/N0/SB2/P0/B1/L3 enabled- pass 1024M DRAM
/N0/SB2/P1/B0/L0 enabled- pass 1024M DRAM
/N0/SB2/P1/B0/L2 enabled- pass 1024M DRAM
/N0/SB2/P1/B1/L1 enabled- pass 1024M DRAM
/N0/SB2/P1/B1/L3 enabled- pass 1024M DRAM
/N0/SB2/P2/B0/L0 enabled- pass 1024M DRAM
/N0/SB2/P2/B0/L2 enabled- pass 1024M DRAM
/N0/SB2/P2/B1/L1 enabled- pass 1024M DRAM
/N0/SB2/P2/B1/L3 enabled- pass 1024M DRAM
/N0/SB2/P3/B0/L0 enabled- pass 1024M DRAM
/N0/SB2/P3/B0/L2 enabled- pass 1024M DRAM
/N0/SB2/P3/B1/L1 enabled- pass 1024M DRAM
/N0/SB2/P3/B1/L3 enabled- pass 1024M DRAM
/N0/IB6/P0 enabled- pass IO Controller 0
/N0/IB6/P1 enabled- pass IO Controller 1
/N0/IB6/P0/B0 enabled- untest 66/33MHz. EPCI/PCI Bus
/N0/IB6/P0/B1 enabled- untest 33MHz PCI Bus
/N0/IB6/P1/B0 enabled- untest 66/33MHz. EPCI/PCI Bus
/N0/IB6/P1/B1 enabled- untest 66/33MHz. EPCI/PCI Bus
/N0/IB6/P1/B0/C0 enabled- untest 66/33MHz. 3.3V Short PCI card
/N0/IB6/P1/B0/C1 enabled- untest 66/33MHz. 3.3V Short PCI card
/N0/IB6/P1/B1/C2 enabled- untest 66/33MHz. 3.3V Short PCI card
/N0/IB6/P1/B1/C3 enabled- untest 66/33MHz. 3.3V Short PCI card
/N0/IB6/P0/B0/C4 enabled- untest 66/33MHz. 3.3V Short PCI card
/N0/IB6/P0/B0/C5 enabled- untest 66/33MHz. 3.3V Short PCI card
/N0/RP0/ enabled- - Repeater Board Slot 10
/N0/RP2/ enabled- - Repeater Board Slot 12 在自检中还有一段
/N0/SB2 : Failed AR interconnect test. Status = 0e000fff
/N0/SB2 : Failed AR interconnect test. Status = 0e000fff
SB2/ar0 Bit in error L2_CMD_VLD
SB2/ar0 Bit in error L2_BIDIPAR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_INCOMING
SB2/ar0 Bit in error L2_PREREQ
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 21:40:13 hlrdbsrv1 lom: AR Interconnect test: System board SB2/ar0 address repeater connections to system board RP0/ar0 failed
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
SB2/ar0 Bit in error L2_ADDR
Tue Feb 05 21:40:24 hlrdbsrv1 lom: AR Interconnect test: System board SB2/ar0 address repeater connections to system board RP0/ar0 failed
Could not find error key:0
Could not find error key:20007ff
Could not find error key:0
Could not find error key:20007ff
Tue Feb 05 21:40:26 hlrdbsrv1 lom: AR Interconnect test: System board SB2/ar0 address repeater connections to system board RP0/ar0 failed
Tue Feb 05 21:40:26 hlrdbsrv1 lom: CPU Board V3 at /N0/SB2 has been removed from domain A due to a failure in interconnection test. Service action required.
Could not find error key:0
Could not find error key:20007ff 换个SB2实施吧。。。:-L 本帖最后由 coologin 于 2013-02-20 15:55 编辑
CPU/内存板在 POST 期间未能通过互连测试,多次后，SB2是否会被列入黑名单？
要将某组件列入黑名单，需要提供列入黑名单的名称。列入黑名单的名称源自组件所属
的系统和子系统。
文档给出两个命令
setls
showcomponet
如是否会出现如下现像？
sc0:sms-user:>showcomponent -a SB0
Component SB0 is disabled: #High Voltage
页:
[1]