[SOLARIS] 8安装问题

yjk_yl

solaris8安装问题

在E3500安装完solaris8后不能启动,stop-a 后出现{6} ok
请问各位手是怎么回事？

yjk_yl

wow!   wonderful !!  i have completely done   it !!

thanks clu65!  thanks jghos !

thanks very much again!!

clu65

Oops! My mistake.

The probe-scsi-all command does not function identically on all platforms and does not in all cases probe for Fibre Channel devices . In such instance, You could use show-devs or you could use probe-fcal & proble-fcal-all to find Fibre Chanle devices.

Note:

1. Try to use nvalias instead of devalias. If you use devalias, you will lose the setting after power recycle.

2. Both internal Disks for E3500 and Disks inside A5x00 Disk Array are using FC-AL interface not SCSI interface.

3. Usually people use external Multipack for OS and external Disk Arrays for application data. You could install the OS on the external A5x00 disk array but not recommended.

jghos

这是在安装E3500时会遇到的问题。我也曾经碰到过。原因就是因为3500用的是光纤硬盘贰不是scsi硬盘，这造成硬盘中的一个wwn号会与disk中的显示有时不一致，而造成无法正常启动。解决方法就是用devalias将你真正在用的硬盘作一个定义（如：mydisk）然后将boot device改成mydisk即可。另：要看3500的硬盘不能用probe-scsi-all,而要用probe-fcal。

clu65

Great.

To auto boot  all you need to do is type \"nvalias disk /sbus@3,0/SUNW,socal@d,10000/sf@0,0/ssd@w2100002037773f92e,0 \" at prom.

Next type reset at prom.

So you must have SUN A5x00 disk array attached to your system. I would recommend you go to http://docs.sun.com to down load some documents about disk array and Prom reference book.

yjk_yl

thank you !!  i have been
i  run  format , it show the  harddisk i installed Solaris is disk0,  and its alias is
\'/sbus@3,0/SUNW,socal@d,10000/sf@0,0/ssd@w2100002037773f92e,0 \'

i try to run command boot  /sbus@3,0/SUNW,socal@d,10000/sf@0,0/ssd@w2100002037773f92e,0
my God , it is OK!!!!

but i don\'t know how i configure my computer make it auto boot, would you tell me? thank you again

what diffences have \'\"/sbus@3,0/SUNW,fas@3,8800000/sd@0,0 \' and   \'sbus@3,0/SUNW,socal@d,10000/sf@0,0/ssd@w2100002037773f92e,0 \'?

i know w210000203773f92e is WWN number in \'sbus@3,0/SUNW,socal@d,10000/sf@0,0/ssd@w2100002037773f92e,0 \', but i don\'t know what meanings WWN number is?

clu65

Could you try rest of suggestion?

And if you sure \"/sbus@3,0/SUNW,fas@3,8800000/sd@0,0 \" is the harddisk you installed Solaris. Please go ahead to boot from cdrom to single user mode by typing \"boot cdrom -s\" at prom. Once you enter the single user mode, try to run format to verify it.

yjk_yl

i have tried all , but nothing happend
when i run  boot disk or  run boot /sbus@3,0/SUNW,fas@3,8800000/sd@0,0  

display follows:
boot device    /sbus@3,0/SUNW,fas@3,8800000/sd@0,0  file and   args:  
then  it die

clu65

Diskbrd and diskisp are just two aliases. You can name anything you want, the more important thing is what physical device (i.e., the physical device path) associated with that alias.

diskbrd /sbus@3,0/SUNW,fas@3,8800000/sd@a,0
diskisp /sbus@3,0/QLGS,isp@3,10000/sd@a,0
In your case, diskbrd refers to a disk with target 10 attached to Sunw Fast/wide SCSI controller on first borad slot in the back and diskisp refers to a disk with target 10(a->10,...f->15) attached to differential SCSI controller.

Now if you remember the logical device name (/dev/dsk/cXtYdZ) and slice number(or partition Number) of the disk you install the Solaris root filesystem, then you can try run\"probe-scsi-all\" to find out actual scsi device attached to your system(the devalias did not show the physical devices you have)

Then you could try run boot phyical_device_path or devalias points that physical device.

If you do not remember  the logcical device name mention above, at o.k., prompt, type boot cdrom -s to boot into single user mode using cd-rom installation medium.

Then run format and check partition table and guess which one could be most likely boot disk, then try to mount that partition under /a and check /a/etc/vfstab to find out boot disk.

Good Luck.

yjk_yl

run command devalias at prompt {a}OK, list

screen          /SUNW,ffb@2,0
disk              /sbus@3,0/SUNW,fas@3,8800000/sd@0,0
diskbrd         /sbus@3,0/SUNW,fas@3,8800000/sd@a,0
diskisp         /sbus@3,0/QLGS,isp@3,10000/sd@a,0
net              /sbus@3,0/SUNW,hme@3,8c00000
cdrom         /sbus@3,0/SUNW,fas@3,8800000/sd@6,0:f
tape           /sbus@3,0/SUNW,fas@3,8800000/st@4,0
scsi            /sbus@3,0/SUNW,fas@3,8800000
disk0         /sbus@3,0/SUNW,fas@3,8800000/sd@0,0
disk1         /sbus@3,0/SUNW,fas@3,8800000/sd@1,0
disk2         /sbus@3,0/SUNW,fas@3,8800000/sd@2,0
disk3         /sbus@3,0/SUNW,fas@3,8800000/sd@3,0
disk4         /sbus@3,0/SUNW,fas@3,8800000/sd@4,0
disk5        /sbus@3,0/SUNW,fas@3,8800000/sd@5,0
tape0       /sbus@3,0/SUNW,fas@3,8800000/st@4,0
tape1       /sbus@3,0/SUNW,fas@3,8800000/st@5,0
ttya          /central/fhc/2s@0,902000:a
ttyb         /central/fhc/2s@0,902000:b
keyboard  /central/fhc/2s@0,904000
keyboard! /central/fhc/2s@0,904000:forcemode

i have another quetion, what\'s meanings of  words diskbrd and diskisp?

list  follows as  when i run command printenv
disabled-memory-list
disabled-board-list
memory-interleave        max
configuration-policy      component
scsi-initiator-id              7
keyborad-click             false
keymap
ttyb-rts-dtr-off               false
ttyb-ignore-cd              true
ttya-rts-dtr-off               false
ttyb-ignore-cd              true
ttyb-mode                   9600,8,n,1,_
ttya-mode                   9600,8,n,1,_
sbus-specific-probe
sbus-probe-default     d3120
mfg-mode                   off
diag-level                   max
powerfail-time             0
#power-cycles          547                       no default value
fcode-debug?          false
output-device          screen
input-device            keyboard
load-base                16384
boot-command        boot
auto-boot                true
watchdog_reboot?  false
diag-file
diag-device            disk diskbrd diskisp disksoc net
boot-file
boot-device             disk diskbrd diskisp disksoc net
local-mac-address    false
ansi-terminal? true
screen-#columns       80
screen-#rows            40
silent-mode?             false
use-hvramrc?            false
nvramrc
security-mode           none            no default value
security-password
security-#badlogins    2684354560   no default value
oem-logo
oem-logo?                 false
oem_banner         
oem-banner?            false
hardware-revision
last-hardware-update   00  no default value
diag-swith?                 true

note:  the every setting\'s value is same as  the its default value  

thank you very much for help me