SCO OpenServer 5开发系统安装和软件管理

sdccf

一、安装SCO OpenServer 5.0.5开发系统
重新启动系统，按照提示，按CTR+D， 连续两次回车，进入login, 并以root登录，进入X-window界面，用鼠标双击Software Manager图标，出现Software Manager窗口， （或在#提示符下，输入custom→software→install new）出现新窗口：
Begin Installation on scosysv
What host (machine) do you want to install from ?
From scosysv
From another host
单击continue, 出现
Select Media
Insert media, and select media device
Media Device: Floppy Disk 0
将鼠标单击右边下箭头，选择出现
SCSI CD-ROM Drive 0
Tape Drive 0
Floppy Disk Drive 0
Loaded Software Media lmages
单击SCSI CD-ROM Drive 0再击CONTINUE。于是系统将从CD-ROM中将其中文件拷入硬盘，注意，这时会出现类似下面的窗口（字符菜单下不会出现）：
Fri Dec 6 08:17:13 1996
cd-rom………………type=s ha=0 id=5 lun=0 bus=0 ht=alad
这是CD-ROM已经连接到系统中的提示,单击continue ,关掉即可，经过一段时间后，出现如下窗口：
Select Product to lnstall on scosysv
Source llost :scosysv
Media Device:SCSL CD-ROM Drive 0
Select A Product to Install
SCO OpenServer Advanced Hardware Supplement (ver 5.2.0c)
SCO ARCServer Open lite from Cheyene (ver 2.1.0e)
SCO Advanced file and Print Server (ver 3.5.1f)
SCO OpenServer Development System (VER 5.0.4h)
SCO Symmetrical Multiprocessing Support (ver 5.0.2Dp)
单击窗口右边滑标，找到
SCO OpenServer Development System (ver 5.0.4b)
单击之，然后点击Full,于是系统正式从光盘安装开发系统并出现如下类似窗口：
Installaion Progress on Scosysv,
Installing :SCO OpenServer D evelopment System (ver 5.0.4h)
Installation phase: copying product files from media
Installation status:…………
一段时间后，出现如下提示窗口：
License Product
Enter the information as printed on the SCO OpenServer Development System Certificate and Authenticity.
License Number:
License Code:
License Data:
按照开发系统许可证上的号码输入以上相应位置，然后单击license.几分钟后，出现如下提示：
Message
SCO OpenServer Development System has been licensed successfully.
SCO require that you register this SCO OpenServer Development System. Please refer to the SCO Software Registration booklet for more information.
单击ok, 回到原来界面继续安装，一段时间后，出现如下窗口：
Message
lnstallation Complete
License and Registration status:
License:Yes
Registered:No
Your Software is installed and licensed.Even though you can use in now.SCO requires that you register this Software. Please refer to the SCO Software Registration booklet for more information.
单击ok, 关闭Software Manager窗口， 开发系统安装完成。
二、注册软件
使用命令scoadmin→License进入LICENSE管理菜单，可获得系统安装时输入的license Number和System ID，将此号mail给SCO公司，SCO返回Registration Key后，进行注册
使用scoadmin→License Manager，选择Register→Register Product完成注册
三、制作应急盘
应急盘由boot软盘和root文件系统软盘组成，包括： /boot，/etc/default/boot，/unix
注意：应急盘是在系统安装后，对系统的一部分进行的备份，因此，它与每个具体的机器密切相关，有着一一对应的关系。
建立应急盘
使用scoadmin→Filesystem
或 mkdev fd命令，则显示
--------------------------------------------------------------
FLOPPY FILESYSTEM CREATION AND EMERGENCY BOOT/ROOT SET PROGRAM
--------------------------------------------------------------
Choices for contents of the floppy filesystem.
1. Filesystem
2. Emergency Boot and Root floppy filesystems
Enter an option or q to quit: 2
选择2，建立应急盘
Emergency Boot and Root floppy filesystems option
-------------------------------------------------
Choices for type of floppy filesystem.
1. 96tpi, double sided, 15 sectors per track (1.2Mb 5.25 inch)
2. 135tpi, double sided, 18 sectors per track (1.44Mb 3.5 inch)
3. 135tpi, double sided, 36 sectors per track (2.88Mb 3.5 inch)
Enter an option or q to quit: 2
选择2，用1.44软盘
Emergency Boot and Root Filesystems
-----------------------------------
Please choose the type of filesystem.
1. Root filesystem
2. Boot filesystem
3. Single floppy Boot and Root filesystem (2.88Mb only)
If you have high density (1.44M) disks, you must create separate root and boot filesystem floppies. The root floppy must be prepared first.
If you have extra density (2.88Mb) disks, you can choose to have both the root and boot filesystems on the same floppy disk.
Enter an option or q to quit: 1
选择要创建的文件系统
Insert a 135ds18 floppy into drive 0
Press to continue or q to quit:
插入软盘，则系统开始创建两个应急盘：可引导的BOOT盘，包含ROOT文件系统的盘
将tar命令拷贝到root应急盘中
# mount /dev/fd0135ds18 /mnt
# cp /bin/tar /mnt/bin
# cp /etc/default/tar /mnt/etc/default
# umount /mnt
当系统出现问题而无法引导时，可用boot应急盘引导，用root应急盘作相应的文件恢复。

本文来自ChinaUnix博客，如果查看原文请点：http://blog.chinaunix.net/u/31/showart_500286.html