请帮助我拨号到CISCO7206

magic541788

win98接MODEM，拨号到CISCO7206如何拨号，7206也接一个MODEM在AUX口，请帮助我，如何写路由器，98如何拨号

dainh

maui-slt-01#show running-config
Building configuration...

Current configuration:
!
version 12.1
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname maui-slt-01
!
aaa new-model
aaa authentication login default local
aaa authentication login NO_AUTHEN none
aaa authentication ppp default local

!--- This is the basic AAA configuration for PPP calls.

enable secret 5 <deleted>;
!
username admin password 0 <deleted>;
username maui-nas-03 password 0 cisco

!--- Defines username for remote router (maui-nas-03) and shared secret password.
!--- Shared secret(used for CHAP authentication) must be the same on both sides.

!
memory-size iomem 30
ip subnet-zero
!
chat-script Dialout ABORT ERROR ABORT BUSY "" "AT" OK "ATDT \T" TIMEOUT 45 CONNECT \c

!--- Sets up chat script "Dialout" used for the dialout connection on aux 0.

modemcap entry MY_USR_MODEM:MSC=&amp;F1S0=1

!--- Modemcap (MY_USR_MODEM) will be applied to the AUX port line interface
!--- This modemcap was created using the command:
!--- modemcap edit MY_USR_MODEM miscellaneous &amp;F1S0=1
!--- Refer to the Modem-Router Connection Guide for more information.

!
interface Loopback0
ip address 172.17.1.1 255.255.255.0
!
interface FastEthernet0/0
ip address 172.16.1.1 255.255.255.0
no keepalive
duplex auto
speed auto
!

! <<-- irrelevant output removed

!
interface Async65

!--- Async interface corresponding to the AUX Port.
!--- This was determined using the show line command.
!--- See External Modem Setup and Troubleshooting Tasks for more details.

no ip address
encapsulation ppp

!--- Use PPP encapsulation over this link.

dialer in-band
dialer pool-member 20

!--- Designate Async65 as member of dialer pool 20.
!--- The command dialer pool 20 is specified in interface Dialer 10.

async default routing

!--- This permits routing over the async interface.
!--- This is required for a routing protocol to run accross the async link.

ppp authentication chap callin
!
interface Dialer10

!---Dialer 10 is the logical interface for Dialer Pool 20.

ip unnumbered Loopback0

!--- Uses the Loopback 0 IP address.

encapsulation ppp
ip ospf demand-circuit
dialer remote-name maui-nas-03

!--- Specifies the remote router name.
!--- This name must match the one used by the remote router for authentication

dialer pool 20

!--- Async 65 is a member of this pool

dialer idle-timeout 900
dialer string 81690

!--- Defines the destination router's phone number

dialer max-call 4096
dialer-group 1

!--- apply interesting traffic definition from dialer-list 1


ppp authentication chap callin

!--- Use CHAP authentication for incoming calls

!
router ospf 5
network 172.16.1.0 0.0.0.255 area 0
network 172.17.1.0 0.0.0.255 area 0
network 172.22.1.0 0.0.0.255 area 0

!---OSPF is used between the routers.
!---A routing protocol is unnecessary if you configure the appropriate static routes.

!
ip classless
ip route 0.0.0.0 0.0.0.0 Dialer10

!--- Default route points to int dialer 10.
!--- This is necessary since OSPF is not configured to send default routes.

no ip http server
!
access-list 101 remark Define Interesting Traffic
access-list 101 deny   ospf any any
access-list 101 permit ip any any
dialer-list 1 protocol ip list 101

!--- Use access list 101 for interesting traffic definition
!--- This is applied to interface Dialer 10 using dialer-group 1

!
line con 0
login authentication NO_AUTHEN
transport input none
!
line aux 0

!--- line interface for the AUX port

exec-timeout 0 0

!--- disable exec timeout on the interface

script dialer Dialout

!--- use chat script "Dialout"

modem InOut

!--- enable incoming and outgoing calls

modem autoconfigure type MY_USR_MODEM

!--- apply the modemcap MY_USR_MODEM that was configured previously

transport input all
stopbits 1

!--- Improve throughput by reducing async framing overhead

speed 115200

!--- The AUX port on the 2600 supports a speed of 115200.
!--- Note: If you are routing through the AUX port, each character generates a
!--- processor interrupt. This is an abnormally high load on the CPU, which can be
!--- resolved by using a lower AUX port speed.

flowcontrol hardware

!--- configures RTS/CTS flow control

line vty 0 4
!
no scheduler allocate
end


maui-nas-03 (5300)

maui-nas-03#show running-config
Building configuration...

Current configuration:
!
version 12.0
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname maui-nas-03
!
aaa new-model
aaa authentication login default local
aaa authentication login NO_AUTHEN none
aaa authentication ppp default local

!--- This is the basic AAA configuration for PPP calls.

enable secret 5 <deleted>;
!
username admin password 0 <deleted>;
username maui-slt-01 password 0 cisco

!--- defines username for remote router (maui-slt-01) and shared secret password.
!--- Shared secret(used for CHAP authentication) must be the same on both sides.

spe 1/0 1/7
firmware location system:/ucode/mica_port_firmware
!
ip subnet-zero
!
isdn switch-type primary-ni
mta receive maximum-recipients 0
!
controller T1 0

!--- Primary T1

framing esf
clock source line primary
linecode b8zs
pri-group timeslots 1-24
!

! <<-- irrelevant output removed

!
interface Loopback0
ip address 172.22.1.1 255.255.255.0
no ip directed-broadcast
!
interface Ethernet0
ip address 172.22.53.105 255.255.255.0
no ip directed-broadcast
no keepalive
!

! <<-- irrelevant output removed

!
interface Serial0:23

!--- D-channel for T1 0

no ip address
no ip directed-broadcast
encapsulation ppp
isdn switch-type primary-ni
isdn incoming-voice modem

!--- This sends incoming async calls to the modems.

fair-queue 64 256 0
ppp authentication chap
!         

! <<-- irrelevant output removed

!
interface Group-Async0

!--- Group-Async interface is used to aggregate the modems.

ip unnumbered Loopback0
no ip directed-broadcast
encapsulation ppp
ip ospf network point-to-point

!--- This identifies the type of OSPF network.

async default routing

!--- This permits routing over the async interface.
!--- This is required for a routing protocol to run on the async link.

async mode interactive
peer default ip address pool clientpool

!--- This assigns an IP address from the pool named "clientpool" for the
!--- incoming call.

ppp authentication chap
group-range 1 96
!
router ospf 5
network 172.22.1.0 0.0.0.255 area 0
network 172.22.53.0 0.0.0.255 area 0
!
ip local pool clientpool 172.22.1.2 172.22.1.30

!--- IP addresses for dialin calls will be given from this pool.

ip classless
no ip http server
!
line con 0
login authentication NO_AUTHEN
transport input none
line 1 96
autoselect ppp
modem InOut
transport preferred lat pad telnet rlogin udptn v120 lapb-ta
transport output lat pad telnet rlogin udptn v120 lapb-ta
line aux 0
line vty 0 4
!
end

zujuhu

good !!!