我的路由器cisco3640是1997年购买的,请教以太网口是什么模式：半双工还是全双工模式？

yjl

我的路由器cisco3640是1997年购买的,请教以太网口是什么模式：半双工还是全双工模式？我在系统怎么看不到是工作在什么模式的呢？

Cisco Internetwork Operating System Software
IOS (tm) 3600 Software (C3640-D-M), Version 12.0(4), RELEASE SOFTWARE (fc1)
Copyright (c) 1986-1999 by cisco Systems, Inc.
Compiled Thu 15-Apr-99 10:31 by ccai
Image text-base: 0x60008918, data-base: 0x60788000

ROM: System Bootstrap, Version 11.1(7)AX [kuong (7)AX], EARLY DEPLOYMENT RELEASE SOFTWARE

(fc2)

XXZX_R3600 uptime is 1 week, 2 days, 21 hours, 13 minutes
System restarted by power-on
System image file is "slot0:c3640-d-mz.120-4.bin"

cisco 3640 (R4700) processor (revision 0x00) with 24576K/8192K bytes of memory.
Processor board ID 06000404
R4700 processor, Implementation 33, Revision 1.0
Bridging software.
X.25 software, Version 3.0.0.
5 Ethernet/IEEE 802.3 interface(s)
2 Serial network interface(s)
DRAM configuration is 64 bits wide with parity disabled.
125K bytes of non-volatile configuration memory.
4096K bytes of processor board System flash (Read/Write)
8192K bytes of processor board PCMCIA Slot0 flash (Read/Write)
16384K bytes of processor board PCMCIA Slot1 flash (Read/Write)


Ethernet0/0 is up, line protocol is up
  Hardware is AmdP2, address is 00e0.1e7f.0ac1 (bia 00e0.1e7f.0ac1)
  Internet address is 192.168.1.1/24
  MTU 1500 bytes, BW 10000 Kbit, DLY 1000 usec, rely 255/255, load 9/255
  Encapsulation ARPA, loopback not set, keepalive set (10 sec)
  ARP type: ARPA, ARP Timeout 04:00:00
  Last input 00:00:02, output 00:00:00, output hang never
  Last clearing of "show interface" counters 00:27:26
  Queueing strategy: fifo
  Output queue 0/40, 71 drops; input queue 0/75, 0 drops
  5 minute input rate 715000 bits/sec, 195 packets/sec
  5 minute output rate 386000 bits/sec, 184 packets/sec
     387474 packets input, 184162610 bytes, 0 no buffer
     Received 776 broadcasts, 0 runts, 0 giants, 0 throttles
     0 input errors, 0 CRC, 0 frame, 0 overrun, 0 ignored, 0 abort
     0 input packets with dribble condition detected
     364251 packets output, 95272180 bytes, 0 underruns
     2 output errors, 76114 collisions, 0 interface resets
     0 babbles, 0 late collision, 20757 deferred
     0 lost carrier, 0 no carrier

还有有没有新版本的IOS适合我现在的这台机器呢？我的内存和FLASH够新版本的系统用吗？请给个IOS，谢谢！！！

ssffzz1

C-3640#show controllers ethernet 0/0
Interface Ethernet0/0
Hardware is AMD Presidio
ADDR: 648B4D34, FASTSEND: 6003539C, MCI_INDEX: 0
DIST ROUTE ENABLED: 0
Route Cache Flag: 11
LADRF=0x0000 0x0100 0x0000 0x0000
CSR0  =0x00000072, CSR3  =0x00001044, CSR4  =0x0000491D, CSR15 =0x00000000
CSR80 =0x0000D900, CSR114=0x00000000, CRDA  =0x07B23800, CXDA  =0x07B23AA0
BCR9 =0x00000000 (half-duplex)
HW filtering information:
  Promiscuous Mode Disabled, PHY Addr Enabled, Broadcast Addr Enabled
  PHY Addr=00D0.585D.FAC0, Multicast Filter=0x0000 0x0100 0x0000 0x0000
amdp2_instance=0x648B5DFC, registers=0x3C000000, ib=0x7B237A0
rx ring entries=32, tx ring entries=64
rxring=0x7B23800, rxr shadow=0x648B6088, rx_head=0, rx_tail=0
txring=0x7B23A40, txr shadow=0x648B613C, tx_head=6, tx_tail=6, tx_count=0
Software MAC address filter(hash:length/addr/mask/hits):
  0xC0:  0  0100.0ccc.cccc  0000.0000.0000         0
spurious_idon=0, filtered_pak=0, throttled=0, enabled=0, disabled=0
rx_framing_err=0, rx_overflow_err=0, rx_buffer_err=0
rx_bpe_err=0, rx_soft_overflow_err=0, rx_no_enp=0, rx_discard=0
tx_one_col_err=0, tx_more_col_err=0, tx_no_enp=0, tx_deferred_err=0
tx_underrun_err=0, tx_late_collision_err=0, tx_loss_carrier_err=6
tx_exc_collision_err=0, tx_buff_err=0, fatal_tx_err=0
hsrp_conf=0, need_af_check=0
tx_limited=0(64)

C-3640#



interface Ethernet0/0
no ip address
half-duplex
使用 no half-duples 配置为全双工模式。

yjl

sh controller e0/0
Interface Ethernet0/0
Hardware is AMD Presidio2
ADDR: 60C19DB0, FASTSEND: 60026E84, MCI_INDEX: 0
DIST ROUTE ENABLED: 0
Route Cache Flag: 11
LADRF=0x0000 0x0000 0x0000 0x0000
CSR0  =0x00000072, CSR3  =0x00001044, CSR4  =0x0000491D, CSR15 =0x00000000
CSR80 =0x0000D900, CSR114=0x00000000, CRDA  =0x01904DB0, CXDA  =0x01904F50
HW filtering information:
  Promiscuous Mode Disabled, PHY Addr Enabled, Broadcast Addr Enabled
  PHY Addr=00E0.1E7F.0AC1, Multicast Filter=0x0000 0x0000 0x0000 0x0000
amdp2_instance=0x60C1B678, registers=0x3C100000, ib=0x1904C80
rx ring entries=32, tx ring entries=64
rxring=0x1904CE0, rxr shadow=0x60C1B848, rx_head=13, rx_tail=0
txring=0x1904F20, txr shadow=0x60C1B8F4, tx_head=3, tx_tail=3, tx_count=0
Software MAC address filter(hash:length/addr/mask/hits):
spurious_idon=0, filtered_pak=0, throttled=0, enabled=0, disabled=0
rx_framing_err=0, rx_overflow_err=0, rx_buffer_err=0
rx_bpe_err=0, rx_soft_overflow_err=0, rx_no_enp=0, rx_discard=0
tx_one_col_err=6637168, tx_more_col_err=10045029, tx_no_enp=0, tx_deferred_err=4597910
tx_underrun_err=0, tx_late_collision_err=0, tx_loss_carrier_err=33
tx_exc_collision_err=330, tx_buff_err=0, fatal_tx_err=0

看那里的呢？  还有我的interface Ethernet0/0
都没有half-duplex这个命令

[ 本帖最后由 yjl 于 2009-5-28 12:02 编辑 ]

beyondfly

我也没有看到是半双工模式