- 论坛徽章:
- 0
|
COMPAQ AlphaServer DS20E 500 MHz Console V6.4-11, Dec 10 2002 08:57:56
P00>>>
P00>>>
P00>>>b
(boot dkb0.0.0.2001.1 -flags A)
block 0 of dkb0.0.0.2001.1 is a valid boot block
reading 16 blocks from dkb0.0.0.2001.1
bootstrap code read in
base = 200000, image_start = 0, image_bytes = 2000(8192)
initializing HWRPB at 2000
initializing page table at 3ff46000
initializing machine state
setting affinity to the primary CPU
jumping to bootstrap code
Digital UNIX boot - Thu Jan 11 14:49:49 EST 2001
Loading vmunix ...
Loading at 0xfffffc0000230000
Current PAL Revision <0x2004e00010161>
Switching to OSF PALcode Succeeded
New PAL Revision <0x200490002015b>
Sizes:
text = 4928784
data = 894912
bss = 1349712
Starting at 0xfffffc0000576170
Loading vmunix symbol table ... [1352712 bytes]
Alpha boot: available memory from 0x2dfc000 to 0x7fffc000
Digital UNIX V4.0F (Rev. 1229); Thu Nov 13 01:45:25 CST 2003
physical memory = 2048.00 megabytes.
available memory = 2001.32 megabytes.
using 7853 buffers containing 61.35 megabytes of memory
Master cpu at slot 0.
Firmware revision: 6.4-11
PALcode: Digital UNIX version 1.91-73
COMPAQ AlphaServer DS20E 500 MHz
pci1 at nexus
pci2001 at pci1 slot 7
itpsa0 at pci2001 slot 0
IntraServer ROM Version V2.0 (c)1998
scsi0 at itpsa0 slot 0
tz4 at scsi0 target 4 lun 0 (LID=0) (COMPAQ SDT-9000 4.05)
itpsa1 at pci2001 slot 1
Checksum read error.
*** Attempt to run on unsupported adapter ***
- Failed to configure device in PCI bus 2001, slot 1 with driver itpsa
...attempting to configure with next matching driver
tu0: DECchip 21140: Revision: 2.2
tu0: auto negotiation capable device
tu0 at pci2001 slot 2
tu0: DEC TULIP (10/100) Ethernet Interface, hardware address: 00-06-2B-01-63-85
tu0: auto negotiation off: selecting 100BaseTX (UTP) port: half duplex
isp0 at pci1 slot 8
isp0: QLOGIC ISP1040B/V2 - Differential Mode
isp0: Firmware revision 5.57 (loaded by console)
isp0: Fast RAM timing enabled.
scsi2 at isp0 slot 0
gpc0 at isa0
PCI device at bus 0, slot 6, function 0 could not be configured:
Vendor ID 0x9004, Device ID 0x7895, Base class 0x1, Sub class 0x0 Sub-VID 0x9004 Sub-DID 0x7895
has no matching entry in the PCI option table
PCI device at bus 0, slot 6, function 1 could not be configured:
Vendor ID 0x9004, Device ID 0x7895, Base class 0x1, Sub class 0x0 Sub-VID 0x9004 Sub-DID 0x7895
has no matching entry in the PCI option table
pci0 at nexus
isa0 at pci0
gpc1 not probed
ace0 at isa0bed
ace1 at isa0
lp0 at isa0
fdi0 at isa0
fd0 at fdi0 unit 0
ata0 at pci0 slot 105 (slot 5, function 1)
ata0: CYPRESS 82C693
scsi3 at ata0 slot 0
rz24 at scsi3 target 0 lun 0 (LID=9) (COMPAQ CD-224E 9.5B)
ata1 at pci0 slot 205 (slot 5, function 2)
ata1: CYPRESS 82C693
scsi4 at ata1 slot 0
usb0 at pci0 slot 305 (slot 5, function 3)
comet0: Card type 'Elsa GLoria' with 8MB framebuffer memory.
comet0 at pci0 slot 7
pci2000 at pci0 slot 9
ee0 at pci2000 slot 4
ee0: COMPAQ Intel 82558 (10/100 Mbps) Ethernet Interface
ee0: Driver Rev = V1.0.22, Chip Rev = 5, hardware address: 00-50-8B-F9-6B-10
ee1 at pci2000 slot 5
ee1: COMPAQ Intel 82558 (10/100 Mbps) Ethernet Interface
ee1: Driver Rev = V1.0.22, Chip Rev = 5, hardware address: 00-50-8B-F9-6B-11
Created FRU table binary error log packet
lvm0: configured.
lvm1: configured.
kernel console: ace0
bootdevice_translate: device cannot be translated 'SCSI 1 2001 0 0 0 0 0'
setconf: Bootdevice parser failed to translate bootdevice SCSI 1 2001 0 0 0 0 0.
panic (cpu 0): setconf: bootdevice_parser failed
DUMP: No primary swap, no explicit dumpdev.
Nowhere to put header, giving up.
CP - SAVE_TERM routine to be called
CP - SAVE_TERM exited with hlt_req = 1, r0 = 00000000.00000000
halted CPU 0
halt code = 5
HALT instruction executed
PC = fffffc0000577e00
如题，情况紧急，请高手指点，谢谢！
[ 本帖最后由 mac2008 于 2009-6-17 14:34 编辑 ] |
|
免费注册
发表于 2009-06-15 09:54
