sun v210光驱引导出错。帮忙看看

yuio654

想重装系统，光驱没法启动


ok boot cdrom
Boot device: /pci@1e,600000/ide@d/cdrom@0,0:f  File and args:
Memory Address not Aligned


ok devalias
screen                   /pci@1d,700000/SUNW,m64B@1
xnet2                    /pci@1d,700000/pci@1/SUNW,hme@0,1:dhcp,
xnet1                    /pci@1e,600000/pci@3/SUNW,hme@0,1:dhcp,
xnet                     /pci@1e,600000/pci@2/SUNW,hme@0,1:dhcp,
net3                     /pci@1d,700000/network@2,1
net2                     /pci@1d,700000/network@2
net1                     /pci@1f,700000/network@2,1
net                      /pci@1f,700000/network@2
cdrom                    /pci@1e,600000/ide@d/cdrom@0,0:f
ide                      /pci@1e,600000/ide@d
disk3                    /pci@1c,600000/scsi@2/disk@3,0
disk2                    /pci@1c,600000/scsi@2/disk@2,0
disk1                    /pci@1c,600000/scsi@2/disk@1,0
disk0                    /pci@1c,600000/scsi@2/disk@0,0
disk                     /pci@1c,600000/scsi@2/disk@0,0
scsi                     /pci@1c,600000/scsi@2
sc-control               /pci@1e,600000/isa@7/rmc-comm@0,3e8
ttyb                     /pci@1e,600000/isa@7/serial@0,2e8
ttya                     /pci@1e,600000/isa@7/serial@0,3f8
name                     aliases


ok boot /pci@1e,600000/ide@d/cdrom@0,0:f
Boot device: /pci@1e,600000/ide@d/cdrom@0,0:f  File and args:
Memory Address not Aligned


ok boot /pci@1e,600000/ide@d/cdrom@0,0:f -s
Boot device: /pci@1e,600000/ide@d/cdrom@0,0:f  File and args: -s
Memory Address not Aligned


ok boot /pci@1e,600000/ide@d/cdrom@0,0:f -sv
Boot device: /pci@1e,600000/ide@d/cdrom@0,0:f  File and args: -sv
Memory Address not Aligned

[ 本帖最后由 yuio654 于 2009-8-3 12:23 编辑 ]

yuio654

ok probe-ide
This command may hang the system if a Stop-A or halt command
has been executed.  Please type reset-all to reset the system
before executing this command.
Do you wish to continue? (y/n) y
  Device 0  ( Primary Master )
         Removable ATAPI Model:

yuio654

ok obdiag
Searching for selftest methods: network network flashprom rtc i2c serial serial rmc-comm ide scsi scsi network network SUNW,m64B
_____________________________________________________________________________
|                                 o b d i a g                                 |
|_________________________ _________________________ _________________________|
|                         |                         |                         |
|  1 SUNW,m64B@1          |  2 flashprom@2,0        |  3 i2c@0,320            |
|  4 ide@d                |  5 network@2            |  6 network@2            |
|  7 network@2,1          |  8 network@2,1          |  9 rmc-comm@0,3e8       |
| 10 rtc@0,70             | 11 scsi@2               | 12 scsi@2,1             |
| 13 serial@0,2e8         | 14 serial@0,3f8         |                         |
|_________________________|_________________________|_________________________|
|       Commands: test test-all except help what setenv set-default exit      |
|_____________________________________________________________________________|
|                   diag-passes=10 diag-level=max test-args=                  |
|_____________________________________________________________________________|

obdiag> test-all
Hit the spacebar to interrupt testing
Testing /pci@1d,700000/SUNW,m64B@1
Display not installed

Test hardware registers -  passed Ok
Test RamDAC -  passed Ok
Test Frame buffer -  passed Ok
.................................... passed
Testing /pci@1e,600000/isa@7/flashprom@2,0 ............................ passed
Testing /pci@1e,600000/isa@7/i2c@0,320 ................................ passed
Testing /pci@1e,600000/ide@d .......................................... passed
Testing /pci@1f,700000/network@2 ...................................... passed
Testing /pci@1d,700000/network@2 ...................................... passed
Testing /pci@1f,700000/network@2,1 .................................... passed
Testing /pci@1d,700000/network@2,1 .................................... passed
Testing /pci@1e,600000/isa@7/rmc-comm@0,3e8 ........................... passed
Testing /pci@1e,600000/isa@7/rtc@0,70 ................................. passed
Testing /pci@1c,600000/scsi@2 ......................................... passed
Testing /pci@1c,600000/scsi@2,1 ....................................... passed
Testing /pci@1e,600000/isa@7/serial@0,2e8 ............................. passed
Testing /pci@1e,600000/isa@7/serial@0,3f8 ............................. passed
Pass:1 (of 10) Errors:0 (of 0) Tests Failed:0 Elapsed Time: 0:0:0:27


10次全部passed

ziggler

http://osdir.com/ml/os.solaris.managers/2003-03/msg00077.html

solaris_unix

把diag-passes 的值设为1，或者把obp用set-defaults 设置为缺省值看看！

yuio654

原帖由 solaris_unix 于 2009-8-3 12:53 发表
把diag-passes 的值设为1，或者把obp用set-defaults 设置为缺省值看看！

diag-passes 这个只是控制diag的检测次数，应该不是他的问题，原来是1，刚调到10
set-defaults  reset-all都已经做过了

yuio654

原帖由 ziggler 于 2009-8-3 12:25 发表
http://osdir.com/ml/os.solaris.managers/2003-03/msg00077.html

我晕，openboot firmware bug？应该不会吧，现在是光驱是可卸载状态，系统里看不到

bash-3.00# iostat -En
c1t0d0           Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: SEAGATE  Product: ST336607LSUN36G  Revision: 0207 Serial No: 0327A24XFT
Size: 36.42GB <36418595328 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
c1t5d0           Soft Errors: 0 Hard Errors: 0 Transport Errors: 0
Vendor: FUJITSU  Product: MAP3367N SUN36G  Revision: 0401 Serial No: 0325N0369Y
Size: 36.42GB <36418595328 bytes>
Media Error: 0 Device Not Ready: 0 No Device: 0 Recoverable: 0
Illegal Request: 0 Predictive Failure Analysis: 0
bash-3.00#

应该是怎么把光驱再给加回去

yuio654

断了一次电，光驱拔下来，然后重新上电，光驱状态还是

Device 0  ( Primary Master )
         Removable ATAPI Model:

easybegin

yuio654

原帖由 easybegin 于 2009-8-3 13:56 发表
????????????????????????????????????????


这个是什么啊？

晕，嘛意思呢？